
Xerox Common Management Interface (XCMI) Standard               04/14/23

--  Module: Communications Configuration TC 
--  File:   52conftc.txt, .dfm 
--  Date:   14 April 2023 - Version 6.026.pub   VersionUpdate 

Xerox Corporation 
XCMI Working Group 
April 2023 


                   Definitions of Textual Conventions
             for Communications Configurations using SMIv2


Status of this Memo 

This document specifies the Comms Config (CC) Textual Conventions (TC).
All XCMI conforming management agents, which implement the CC MIB, SHALL
implement the Comms Config and Comms Option groups in the XCMI CC MIB.  

This document specifies an XCMI (Xerox Common Management Interface)
official standard MIB module for the entire Xerox community, and
requests discussion and suggestions for improvements.  Distribution of
this memo is unlimited (within Xerox).  
































XCMI Working Group                File 52conftc                 [Page 1]

Xerox Common Management Interface (XCMI) Standard               04/14/23



1.  Introduction

This document specifies the Comms Config (CC) Textual Conventions (TC).
All XCMI conforming management agents, which implement the CC MIB, SHALL
implement the Comms Config and Comms Option groups in the XCMI CC MIB.  

This CC TC is a companion to the CC MIB (published separately).  

This CC TC is also explained in significant detail in the companion XCMI
Comms MIBs Users Guide (published separately).  

This CC TC has been written in ASN.1 (OSI Abstract Syntax Notation One -
CCITT X.208/209 | ISO 8824/8825), using the IETF SMI for SNMPv2
(Structure of Management Information - RFC 1442/1902/2578), the IETF TC
for SNMPv2 (Textual Conventions - RFC 1443/1903/2579), the IETF CONF for
SNMPv2 (Conformance Statements - RFC 1444/1904/2580), and the IETF Host
Resources MIB (RFC 2790) macros and textual conventions.  


2.  SNMP Network Management Framework

See section 2 'The SNMP Network Management Framework' in the XCMI
General TC (06gentc).  






























XCMI Working Group                File 52conftc                 [Page 2]

Xerox Common Management Interface (XCMI) Standard               04/14/23



3.  Managed Object Usage



3.1.  Overview of Groups in CC MIB

Six object groups are specified in the Comms Config MIB, as follows:  

1)  Comms Config Group (Mandatory) 
    - 'xcmCommsConfigTable' contains one entry for each of one or more
    Communications Engines (ie, collections of protocol stacks,
    addresses, etc) resident on this host system; 
    
2)  Comms Option Group (Mandatory) 
    - 'xcmCommsOptionTable' contains one entry for each of one or more
    communications options associated with communications entities
    within Communications Engines (ie, collections of protocol stacks,
    addresses, etc) resident on this host system; 
    
3)  Directory Record Group (Cond Mandatory) 
    - 'xcmCommsDirRecordTable' contains one entry for each of one or
    more directory records resident on this host system; 
    
4)  Directory Attribute Group (Cond Mandatory) 
    - 'xcmCommsDirAttributeTable' contains one entry for each of one or 
    more integer-valued directory attributes associated with some
    directory record resident on this host system; 
    
5)  Directory String Group (Cond Mandatory) 
    - 'xcmCommsDirStringTable' contains one entry for each of one or
    more string-valued directory attributes associated with some
    directory record resident on this host system; 
    
6)  Comms Protocol Group (Cond Mandatory) 
    - 'xcmCommsDirStringTable' contains one entry for each of one or
    communications protocol suites and/or specific protocols available
    (to be configured) on this host system; 
















XCMI Working Group                File 52conftc                 [Page 3]

Xerox Common Management Interface (XCMI) Standard               04/14/23



3.2.  Relationship of CC MIB to other MIBs



3.2.1.  IETF Interfaces Group MIB (RFC 2233)

The entire CC MIB was inspired by the Interfaces Group MIB (RFC 2233).  


3.2.2.  IETF Communications MIBs

Many products include Communications Engines of considerable complexity,
but the communications capabilities are ancillary to the main purpose of
the product (eg, network printers) - in such products, the use of the CC
MIB stand-alone can save significant implementation costs and still
yield an acceptable level of communications configuration and operations
management product capability.  

On the other hand, even products which implement many network interface 
and protocol suite specific IETF Communications MIBs may still benefit
significantly from adding support for the CC MIB, with its numerous
features and capabilities not found in any legacy IETF Communications
MIB.  


3.2.3.  XCMI Communications Engine MIB

The CC MIB is complementary to the XCMI Communications Engine MIB, but
MAY be used stand-alone.  


3.2.4.  XCMI General MIB for Reconfiguration

XCMI conforming management stations and management agents shall ALWAYS
use the facilities provided by the General Reconf and General Option
groups of the XCMI General MIB to perform orderly and atomic
reconfiguration of communications options of managed host systems.  
















XCMI Working Group                File 52conftc                 [Page 4]

Xerox Common Management Interface (XCMI) Standard               04/14/23



3.3.  Comms Option Instance Resolution

Unlike most other MIB objects, which are normally stored in 'well-known'
dedicated OIDs (with explicit instance identification, when found in
tables), the objects which are defined in the XCMI Comms Config TC
(52conftc.txt) are ONLY stored in generic 'containers'.  


It has been pointed out that a managed system which defines a
'pseudo-table' of five (5) instances of the same Comms Option (eg,
'xcmCONetwareFServerName') must ALWAYS make clear which instance is to
be changed via a General Option specified in the XCMI General MIB.  

The following algorithm shall ONLY apply to managed systems which choose
'fixed' values of 'xcmCommsOptionIndex' for particular instances of
their communications configuration options.  Support for this algorithm 
is NOT a conformance requirement for the XCMI Comms Config MIB.  But,
for supporting systems, the recommended algorithm (already implemented
by several product teams) is as follows:  

if 
    (('xcmGenOptionTypeOID' == 'xcmCommsOptionTypeOID') && 
     ('xcmGenOptionIndex'   == 'xcmCommsOptionIndex')) 
then 
    { the instances are equivalent } 



























XCMI Working Group                File 52conftc                 [Page 5]

Xerox Common Management Interface (XCMI) Standard               04/14/23



3.4.  SNMP Transport Protocols and Domains

Historically, all SNMP protocol mappings are over connectionless
transport, network, or datalink layer protocols.  Recently (2000), the
IETF (Internet Engineering Task Force) and IRTF (Internet Research Task 
Force) have begun to develop SNMP over connection-oriented transport
layer protocols for bulk data transfer and reliability.  

See:  'draft-irtf-nmrg-snmp-tcp-06.txt', March 2001.  

See:  'XcmGenSNMPDomain' textual convention in XCMI General TC.  

See:  SNMP Transport Mappings, RFC 1906, January 1996.  


3.4.1.  SNMP over Internet UDP

XCMI - snmpUDPDomain - enum 

IETF - snmpUDPDomain - OID 

See:  User Datagram Protocol, RFC 768, August 1980.  



3.4.2.  SNMP over OSI CLNS

OSI Transport Class 4 over OSI Connectionless Network Service 

XCMI - snmpCLNSDomain - enum 

IETF - snmpCLNSDomain - OID 

See:  OSI Transport Service, ISO 8072.  



3.4.3.  SNMP over OSI CONS

OSI Transport Class 0 over OSI Connection-oriented Network Service 

XCMI - snmpCONSDomain - enum 

IETF - snmpCONSDomain - OID 

See:  OSI Connectionless Transport Service, ISO 8072/AD 1 







XCMI Working Group                File 52conftc                 [Page 6]

Xerox Common Management Interface (XCMI) Standard               04/14/23



3.4.4.  SNMP over AppleTalk DDP

AppleTalk DDP connectionless network protocol 

XCMI - snmpDDPDomain - enum 

IETF - snmpDDPDomain - OID 

See:  Inside AppleTalk (2nd Edition), Addison-Wesley, 1990.  



3.4.5.  SNMP over NetWare IPX

NetWare IPX connectionless network protocol 

XCMI - snmpIPXDomain - enum 

IETF - snmpIPXDomain - OID 

See:  Network System Technical Interface Overview, Novell, June 1989.  



3.4.6.  SNMP over NetBIOS (session)

NetBIOS session protocol 

XCMI - snmpNetBIOSDomain - enum 

IETF - none 

See:  'xcmSnmpNetbiosDomain' and 'XcmSnmpNetbiosAddress' in XCMI CC TC.



3.4.7.  SNMP over NetBEUI (datalink)

NetBEUI datalink (IBM DLC) protocol 

XCMI - snmpNetBEUIDomain - enum 

IETF - none 

See:  HP Laser Printer implementations 



3.4.8.  SNMP over Internet TCP (Experimental)

XCMI - snmpTCPDomain - enum (to be assigned) 


XCMI Working Group                File 52conftc                 [Page 7]

Xerox Common Management Interface (XCMI) Standard               04/14/23


IETF - snmpTCPDomain - OID (in IETF Experimental tree) 

See:  'draft-irtf-nmrg-snmp-tcp-06.txt', March 2001.  

See:  Transmission Control Protocol, RFC 793, September 1981.  



3.4.9.  SNMP over UDP using hostname instead of IP address

XCMI - snmpIPHostnameDomain - enum 

IETF - none 

See:  'xcmSnmpIPHostnameDomain'and 'XcmSnmpIPHostnameAddress' in XCMI CC
TC.  






































XCMI Working Group                File 52conftc                 [Page 8]

Xerox Common Management Interface (XCMI) Standard               04/14/23



4.  Managed Object Definitions



4.1.  Definition of CC Textual Conventions

XEROX-COMMS-CONFIG-TC DEFINITIONS ::= BEGIN 
--  Module: Communications Configuration TC 
--  File:   52conftc.mib 
--  Date:   14 April 2023 - Version 6.026.pub VersionUpdate 

--  Textual Conventions companion to the Comms Config MIB 
--  Contains the REGISTRY of XCMI Standard NetBIOS Listen Ports 

IMPORTS 
    MODULE-IDENTITY, OBJECT-IDENTITY, 
        OBJECT-TYPE 
            FROM SNMPv2-SMI             -- IETF RFC 1442/1902/2578 
    TEXTUAL-CONVENTION 
            FROM SNMPv2-TC              -- IETF RFC 1443/1903/2579 
    xeroxCommonMIB 
            FROM XEROX-COMMON-MIB; 

xcmCommsConfigTC MODULE-IDENTITY 
    LAST-UPDATED "2304140000Z" -- 14 April 2023 
    ORGANIZATION "Xerox Corporation - XCMI Working Group" 
    CONTACT-INFO 
        "           XCMI Editors 
        Email:      XCMI.Editors@xerox.com 
        " 
    DESCRIPTION 
        "Version:   6.026.pub 

        The TC module for textual conventions, enumerated types, OIDs, 
        and other volatile elements of the companion Communications 
        Config MIB, which supports active configuration discovery of 
        communications end system applications, communications 
        intermediate systems, and communications gateways for network 
        accessible host systems. 

        Copyright (C) 1996-2020 Xerox Corporation. All Rights Reserved."
    ::= { xeroxCommonMIB 63 } 

-- 
--          The Comms Config TC 
-- 
--          Textual Conventions 

-- 
--          SNMP over NetBIOS Transport Domain and Transport Address 
-- 
--          For use with SNMPv1/v2 protocols over the NetBIOS. 

XCMI Working Group                File 52conftc                 [Page 9]

Xerox Common Management Interface (XCMI) Standard               04/14/23

-- 
--          See section 2.0 'Definitions' of SNMPv2 Transport Mappings 
--          (RFC 1449/1906) for information on SNMP mappings over other 
--          network/transport protocols from other protocol suites. 

xcmSnmpNetbiosDomain OBJECT-IDENTITY 
    STATUS      current 
    DESCRIPTION 
        "The SNMP over NetBIOS transport domain.  The corresponding 
        transport address is of type 'XcmSnmpNetbiosAddress'." 
    ::= { xcmCommsConfigTC 3 } 

XcmSnmpNetbiosAddress ::= TEXTUAL-CONVENTION 
    STATUS      current 
    DESCRIPTION 
        "The canonical NetBIOS transport address.  The corresponding 
        SNMP over NetBIOS transport domain is 'xcmSnmpNetbiosDomain'. 

        The canonical NetBIOS transport address 
        (registered as a NetBIOS session layer name via 'AddName'): 

            Octets      Contents        Encoding 
            ------      --------        -------- 
              1-12      MAC-address     ASCII hexadecimal (uppercase) 
                        [IEEE 802.x]        ('0'-'9', 'A'-'F') 
             13-14      XCMI-reserved   ASCII decimal zeros 
                        [XCMI future]       ('0' - 0x30) 
             15-16      NetBIOS-port    binary network-byte order 
                        [XCMI std port]     (high-order byte first) 
        " 
    SYNTAX  OCTET STRING (SIZE (16)) 

xcmSnmpIPHostnameDomain OBJECT-IDENTITY 
    STATUS      current 
    DESCRIPTION 
        "The transport domain for SNMP over UDP when  
         using host name instead of IP address.  The corresponding 
         transport address is of type 'XcmSnmpIPHostnameAddress'." 
    ::= { xcmCommsConfigTC 5 } 

XcmSnmpIPHostnameAddress ::= TEXTUAL-CONVENTION 
    STATUS      current 
    DESCRIPTION 
        "The transport address.  The corresponding 
        transport domain is 'xcmSnmpIPHostnameDomain'. 

            Octets      Contents            Encoding 
            ------      --------            -------- 
              1         Host Name Length    unsigned char 0-255 
              2-n       FQDN                 
              n+1, n+2  UDP Port                                " 

    SYNTAX  OCTET STRING (SIZE (255)) 


XCMI Working Group                File 52conftc                [Page 10]

Xerox Common Management Interface (XCMI) Standard               04/14/23


-- 
--          REGISTRY of XCMI Standard NetBIOS Ports 
--          (used with XCMI standard SNMP over NetBIOS mapping) 
-- 
--          Entity                      Listen Port 
--          ------                      ----------- 
--          SNMP management agent       161 (decimal) 
--          SNMP management station     162 (decimal) 

-- 
--          Comms Options Types and Syntaxes 
-- 
--          Implementation of these options is optional for all systems,
--          and useful for ones which implement stack layer graphing 
--          (via the Stack and Mux Groups) and ALSO for ones which do 
--          NOT implement stack layer graphing (eg, low cost systems). 

XcmCommsConfigGroupSupport ::= TEXTUAL-CONVENTION 
    STATUS      current 
    DESCRIPTION 
        "The terse conformance statement of ALL mandatory, conditionally
        mandatory, and optional XCMI Comms Config MIB object groups 
        supported by this management agent implementation (ie, version) 
        on this host system, specified in a bit-mask. 

        The current set of values (which MAY be extended in the future) 
        is given below: 

              1 : commsConfigGroup            -- 2**0 
              2 : commsOptionGroup            -- 2**1 
              4 : commsDirRecordGroup         -- 2**2 
              8 : commsDirAttributeGroup      -- 2**3 
             16 : commsDirStringGroup         -- 2**4 
             32 : commsProtocolGroup          -- 2**5 

        Usage:  Conforming management agents SHALL accurately 
        report their support for XCMI Comms Config MIB object groups." 
    SYNTAX      INTEGER (0..2147483647)  -- biggest int = 2**31-1 

XcmCommsDirRecordType ::= TEXTUAL-CONVENTION 
    STATUS      current 
    DESCRIPTION 
        "The type of the directory record specified 
        in this conceptual row in the 'xcmCommsDirRecordTable'. 

        Usage:  Directory records of type 'recordXxxGroup' SHALL 
        contain only 'xxxIndex' directory attributes (ie, pointers to 
        individual 'recordXxx' directory records)." 
    SYNTAX      INTEGER { 
        other(1),                       -- see key attribute type/index 
        unknown(2),                     -- NOT valid as record type 
        top(10),                        -- top (root of directory) 
        recordService(100),             -- individual service record 

XCMI Working Group                File 52conftc                [Page 11]

Xerox Common Management Interface (XCMI) Standard               04/14/23

        recordServiceGroup(101),        -- group of service records 
        recordAccount(200),             -- individual account record 
        recordAccountGroup(201),        -- group of account records 
        recordDepartment(300),          -- individual department record 
        recordDepartmentGroup(301),     -- group of department records 
        recordMailbox(400),             -- individual mailbox record 
        recordMailboxGroup(401),        -- group of mailboxe records 
        recordResource(500),            -- individual resource record 
        recordResourceGroup(501),       -- group of resource records 
        recordSpeedDial(600),           -- individual speed dial record 
        recordSpeedDialGroup(601),      -- group of speed dial records 
        recordUser(700),                -- individual user 
        recordUserGroup(701),           -- group of users 
        recordButtonDial(800),          -- individual button dial record
        recordButtonDialGroup(801),     -- group of button dial records 
        recordRepository(900),          -- individual repository 
        recordRepositoryGroup(901)      -- group of repositories 
    } 

XcmCommsDirAttributeType ::= TEXTUAL-CONVENTION 
    STATUS      current 
    DESCRIPTION 
        "A directory attribute type, used to identify this 
        integer-valued directory attribute, which MAY have a matching 
        string-valued directory attribute in 'xcmCommsDirStringTable'. 

        Usage:   When directory attribute type indicates integer-valued,
        the value of 'xcmCommsDirAttributeValue' SHALL be the 
        actual value of this directory attribute. 

        Usage:   When directory attribute type indicates string-valued, 
        the value of 'xcmCommsDirAttributeValue' SHALL be zero, 
        EXCEPT for a directory attribute type of 'protocolTyped...', 
        when the protocol type SHALL be specified as the integer value. 
        The actual string-valued attribute SHALL be specified in 
        an exactly matching row of 'xcmCommsDirStringTable'. 

        Usage:  Matching directory attributes (string-valued) 
        SHALL be specified in an exactly matching row of 
        'xcmCommsDirStringTable'.  Matching rows have EXACTLY the SAME 
        values of 'xcmCommsDirRecordType', 'xcmCommsDirRecordIndex', 
        'xcmCommsDirAttributeType', and 'xcmCommsDirAttributeIndex'. 

        Usage:  Parallel directory attributes (peers of this one) 
        SHALL be specified in parallel (NOT matching) rows of 
        'xcmCommsDirAttributeTable' (integer-valued attributes) or 
        'xcmCommsDirStringTable' (string-valued attributes).  Parallel 
        rows have EXACTLY the SAME values of 'xcmCommsDirRecordType', 
        'xcmCommsDirRecordIndex', and 'xcmCommsDirAttributeIndex', 
        but MUST have a DIFFERENT value of 'xcmCommsDirAttributeType'. 

        Usage:   When directory attribute type is 'protocolTyped...' the
        particular protocol layer SHALL be specified by placing a 
        a value from the enumeration 'XcmCommsStackExtProtocol' in 

XCMI Working Group                File 52conftc                [Page 12]

Xerox Common Management Interface (XCMI) Standard               04/14/23

        'xcmCommsDirAttributeValue' for this row." 
    REFERENCE 
        "See:   'xcmCommsDirAttributeType' in the XCMI Comms Config MIB 
                'XcmCommsStackExtProtocol' in the XCMI Comms Engine TC."
    SYNTAX      INTEGER { 
        --  WARNING - this enumeration is work-in-progress - do NOT use 
        other(1), 
        unknown(2), 
        --  Structural directory attributes (integer-valued) 
        -- 
        parentRecordType(10),           -- (xcmCommsDirRecordType) 
        parentRecordIndex(11),          -- (xcmCommsDirRecordIndex) 
        parentGroupRecordType(12),      -- (xcmCommsDirRecordType) 
        parentGroupRecordIndex(13),     -- (xcmCommsDirRecordIndex) 
        peerRecordType(20),             -- (xcmCommsDirRecordType) 
        peerRecordIndex(21),            -- (xcmCommsDirRecordIndex) 
        peerGroupRecordType(22),        -- (xcmCommsDirRecordType) 
        peerGroupRecordIndex(23),       -- (xcmCommsDirRecordIndex) 
        childRecordType(30),            -- (xcmCommsDirRecordType) 
        childRecordIndex(31),           -- (xcmCommsDirRecordIndex) 
        childGroupRecordType(32),       -- (xcmCommsDirRecordType) 
        childGroupRecordIndex(33),      -- (xcmCommsDirRecordIndex) 
        --  Service directory attributes (integer-valued) 
        -- 
        serviceIndex(100),              -- (xcmCommsDirRecordIndex) 
        serviceGroupIndex(101),         -- (xcmCommsDirRecordIndex) 
        servicePosixRights(102),        -- (XcmSecPosixRights) 
        servicePosixVerbs(103),         -- (XcmSecPosixVerbs) 
        serviceType(110),               -- (XcmSvcMonServiceType) 
        serviceSkill(111),              -- (XcmSecUserSkill) 
        serviceScope(112),              -- (XcmSecAccountScope) 
        servicePhysicalDeviceIndex(120),-- (hrDeviceIndex) 
        serviceLogicalDeviceIndex(121), -- (hrDeviceIndex) 
        serviceExternalDeviceIndex(122),-- (hrDeviceIndex) 
        serviceSWRunIndex(123),         -- (hrSWRunIndex) 
        serviceSWInstalledIndex(124),   -- (hrSWInstalledIndex) 
        serviceStorageIndex(125),       -- (hrStorageIndex) 
        servicePriority(130),           -- (xcmSvcMonServicePriority) 
        --  Service lifetime usage and limits (integer-valued) 
        --  ('serviceLifetimeUsage' SHALL have subtype per 
        --  the 'XcmGenMessageMapStringLabel' syntax in XCMI General TC)
        --  specified in 'xcmCommsDirStringValue') 
        --  ('serviceLifetimeUsage' MAY have units class/type specified 
        --  in parallel '...[UnitClass|Unit]' rows) 
        serviceLifetimeUsage(140),          -- (deviceLifetimeUsage) 
        serviceLifetimeUnitClass(141),      -- (xcmHrDevDetailUnitClass)
        serviceLifetimeUnit(142),           -- (xcmHrDevDetailUnit) 
        serviceLifetimeLimit(143),          -- (deviceMaximumLifetime...
        --  Service lifetime errors and warnings (integer-valued) 
        --  ('serviceLifetime[Error|Warning]Count' MAY have subtype per 
        --  the 'XcmGenMessageMapStringLabel' syntax in XCMI General TC,
        --  specified in 'xcmCommsDirStringValue') 
        serviceLifetimeErrorCount(144),     -- (deviceLifetimeErrorCount
        serviceLifetimeErrorLimit(145),     -- (deviceLifetimeErrorLimit

XCMI Working Group                File 52conftc                [Page 13]

Xerox Common Management Interface (XCMI) Standard               04/14/23

        serviceLifetimeWarningCount(146),   -- (deviceLifetimeWarning...
        serviceLifetimeWarningLimit(147),   -- (deviceLifetimeWarning...
        --  Service directory attributes (string-valued) 
        -- 
        serviceName(150),               -- (...Utf8String) 
        serviceFullName(151),           -- (...Utf8String) 
        serviceCode(152),               -- (...Utf8String) 
        servicePassword(153),           -- (...Utf8String) 
        servicePasscode(154),           -- (...Utf8String) 
        serviceAlias(155),              -- (...Utf8String) 
        serviceLoginDate(156),          -- (DateAndTime) 
        serviceLogoutDate(157),         -- (DateAndTime) 
        serviceDescription(160),        -- (...Utf8String) 
        serviceLocation(161),           -- (...Utf8String) 
        serviceTypeOID(162),            -- (...Utf8String) - string OID 
        serviceProductID(163),          -- (ProductID) - see '93pidtc' 
        serviceLanguageConfigured(170), -- (...Utf8String) - RFC 1766 
        serviceLanguageSupported(171),  -- (...Utf8String) - RFC 1766 
        serviceCharsetConfigured(172),  -- (...Utf8String) - IANA name 
        serviceCharsetSupported(173),   -- (...Utf8String) - IANA name 
        serviceTree(180),               -- (...Utf8String) 
        serviceContext(181),            -- (...Utf8String) 
        serviceVolume(182),             -- (...Utf8String) 
        servicePath(183),               -- (...Utf8String) 
        --  Account directory attributes (integer-valued) 
        -- 
        accountIndex(200),              -- (xcmCommsDirRecordIndex) 
        accountGroupIndex(201),         -- (xcmCommsDirRecordIndex) 
        accountPosixRights(202),        -- (XcmSecPosixRights) 
        accountPosixVerbs(203),         -- (XcmSecPosixVerbs) 
        accountRole(210),               -- (XcmSecUserRole) 
        accountSkill(211),              -- (XcmSecUserSkill) 
        accountScope(212),              -- (XcmSecAccountScope) 
        --  Account lifetime usage and limits (integer-valued) 
        --  ('accountLifetimeUsage' SHALL have subtype per 
        --  the 'XcmGenMessageMapStringLabel' syntax in XCMI General TC)
        --  specified in 'xcmCommsDirStringValue') 
        --  ('accountLifetimeUsage' MAY have units class/type specified 
        --  in parallel '...[UnitClass|Unit]' rows) 
        accountLifetimeUsage(240),          -- (deviceLifetimeUsage) 
        accountLifetimeUnitClass(241),      -- (xcmHrDevDetailUnitClass)
        accountLifetimeUnit(242),           -- (xcmHrDevDetailUnit) 
        accountLifetimeLimit(243),          -- (deviceMaximumLifetime...
        --  Account lifetime errors and warnings (integer-valued) 
        --  ('accountLifetime[Error|Warning]Count' MAY have subtype per 
        --  the 'XcmGenMessageMapStringLabel' syntax in XCMI General TC,
        --  specified in 'xcmCommsDirStringValue') 
        accountLifetimeErrorCount(244),     -- (deviceLifetimeErrorCount
        accountLifetimeErrorLimit(245),     -- (deviceLifetimeErrorLimit
        accountLifetimeWarningCount(246),   -- (deviceLifetimeWarning...
        accountLifetimeWarningLimit(247),   -- (deviceLifetimeWarning...
        --  Account directory attributes (string-valued) 
        -- 
        accountName(250),               -- (...Utf8String) 

XCMI Working Group                File 52conftc                [Page 14]

Xerox Common Management Interface (XCMI) Standard               04/14/23

        accountFullName(251),           -- (...Utf8String) 
        accountCode(252),               -- (...Utf8String) 
        accountPassword(253),           -- (...Utf8String) 
        accountPasscode(254),           -- (...Utf8String) 
        accountAlias(255),              -- (...Utf8String) 
        accountLoginDate(256),          -- (DateAndTime) 
        accountLogoutDate(257),         -- (DateAndTime) 
        accountDescription(260),        -- (...Utf8String) 
        accountLocation(261),           -- (...Utf8String) 
        --  Department directory attributes (integer-valued) 
        -- 
        departmentIndex(300),           -- (xcmCommsDirRecordIndex) 
        departmentGroupIndex(301),      -- (xcmCommsDirRecordIndex) 
        --  Department directory attributes (string-valued) 
        -- 
        departmentName(350),            -- (...Utf8String) 
        departmentFullName(351),        -- (...Utf8String) 
        departmentCode(352),            -- (...Utf8String) 
        departmentDescription(360),     -- (...Utf8String) 
        departmentLocation(361),        -- (...Utf8String) 
        --  Mailbox directory attributes (integer-valued) 
        -- 
        mailboxIndex(400),              -- (xcmCommsDirRecordIndex) 
        mailboxGroupIndex(401),         -- (xcmCommsDirRecordIndex) 
        --  Mailbox directory attributes (string-valued) 
        -- 
        mailboxName(450),               -- (...Utf8String) 
        mailboxFullName(451),           -- (...Utf8String) 
        mailboxCode(452),               -- (...Utf8String) 
        mailboxDescription(460),        -- (...Utf8String) 
        mailboxLocation(461),           -- (...Utf8String) 
        --  Resource directory attributes (integer-valued) 
        -- 
        resourceIndex(500),             -- (xcmCommsDirRecordIndex) 
        resourceGroupIndex(501),        -- (xcmCommsDirRecordIndex) 
        resourcePosixRights(502),       -- (XcmSecPosixRights) 
        resourcePosixVerbs(503),        -- (XcmSecPosixVerbs) 
        resourceType(510),              -- (XcmRsrcType) 
        resourceSkill(511),             -- (XcmSecUserSkill) 
        resourceScope(512),             -- (XcmSecAccountScope) 
        --  Resource lifetime usage and limits (integer-valued) 
        --  ('resourceLifetimeUsage' SHALL have subtype per 
        --  the 'XcmGenMessageMapStringLabel' syntax in XCMI General TC)
        --  specified in 'xcmCommsDirStringValue') 
        --  ('resourceLifetimeUsage' MAY have units class/type specified
        --  in parallel '...[UnitClass|Unit]' rows) 
        resourceLifetimeUsage(540),         -- (deviceLifetimeUsage) 
        resourceLifetimeUnitClass(541),     -- (xcmHrDevDetailUnitClass)
        resourceLifetimeUnit(542),          -- (xcmHrDevDetailUnit) 
        resourceLifetimeLimit(543),         -- (deviceMaximumLifetime...
        --  Resource lifetime errors and warnings (integer-valued) 
        --  ('resourceLifetime[Error|Warning]Count' MAY have subtype per
        --  the 'XcmGenMessageMapStringLabel' syntax in XCMI General TC,
        --  specified in 'xcmCommsDirStringValue') 

XCMI Working Group                File 52conftc                [Page 15]

Xerox Common Management Interface (XCMI) Standard               04/14/23

        resourceLifetimeErrorCount(544),    -- (deviceLifetimeErrorCount
        resourceLifetimeErrorLimit(545),    -- (deviceLifetimeErrorLimit
        resourceLifetimeWarningCount(546),  -- (deviceLifetimeWarning...
        resourceLifetimeWarningLimit(547),  -- (deviceLifetimeWarning...
        --  Resource directory attributes (string-valued) 
        -- 
        resourceName(550),              -- (...Utf8String) 
        resourceFullName(551),          -- (...Utf8String) 
        resourceCode(552),              -- (...Utf8String) 
        resourcePassword(553),          -- (...Utf8String) 
        resourcePasscode(554),          -- (...Utf8String) 
        resourceAlias(555),             -- (...Utf8String) 
        resourceLoginDate(556),         -- (DateAndTime) 
        resourceLogoutDate(557),        -- (DateAndTime) 
        resourceDescription(560),       -- (...Utf8String) 
        resourceLocation(561),          -- (...Utf8String) 
        --  Speed Dial directory attributes (integer-valued) 
        -- 
        speedDialIndex(600),            -- (xcmCommsDirRecordIndex) 
        speedDialGroupIndex(601),       -- (xcmCommsDirRecordIndex) 
        --  Speed Dial directory attributes (string-valued) 
        -- 
        speedDialName(650),             -- (...Utf8String) 
        speedDialFullName(651),         -- (...Utf8String) 
        speedDialCode(652),             -- (...Utf8String) 
        speedDialDescription(660),      -- (...Utf8String) 
        speedDialLocation(661),         -- (...Utf8String) 
        --  User directory attributes (integer-valued) 
        -- 
        userIndex(700),                 -- (xcmCommsDirRecordIndex) 
        userGroupIndex(701),            -- (xcmCommsDirRecordIndex) 
        userPosixRights(702),           -- (XcmSecPosixRights) 
        userPosixVerbs(703),            -- (XcmSecPosixVerbs) 
        userRole(710),                  -- (XcmSecUserRole) 
        userSkill(711),                 -- (XcmSecUserSkill) 
        userScope(712),                 -- (XcmSecAccountScope) 
        --  User lifetime usage and limits (integer-valued) 
        --  ('userLifetimeUsage' SHALL have subtype per 
        --  the 'XcmGenMessageMapStringLabel' syntax in XCMI General TC)
        --  specified in 'xcmCommsDirStringValue') 
        --  ('userLifetimeUsage' MAY have units class/type specified 
        --  in parallel '...[UnitClass|Unit]' rows) 
        userLifetimeUsage(740),             -- (deviceLifetimeUsage) 
        userLifetimeUnitClass(741),         -- (xcmHrDevDetailUnitClass)
        userLifetimeUnit(742),              -- (xcmHrDevDetailUnit) 
        userLifetimeLimit(743),             -- (deviceMaximumLifetime...
        --  User lifetime errors and warnings (integer-valued) 
        --  ('userLifetime[Error|Warning]Count' MAY have subtype per 
        --  the 'XcmGenMessageMapStringLabel' syntax in XCMI General TC,
        --  specified in 'xcmCommsDirStringValue') 
        userLifetimeErrorCount(744),        -- (deviceLifetimeErrorCount
        userLifetimeErrorLimit(745),        -- (deviceLifetimeErrorLimit
        userLifetimeWarningCount(746),      -- (deviceLifetimeWarning...
        userLifetimeWarningLimit(747),      -- (deviceLifetimeWarning...

XCMI Working Group                File 52conftc                [Page 16]

Xerox Common Management Interface (XCMI) Standard               04/14/23

        --  User directory attributes (string-valued) 
        -- 
        userName(750),                  -- (...Utf8String) 
        userFullName(751),              -- (...Utf8String) 
        userCode(752),                  -- (...Utf8String) 
        userPassword(753),              -- (...Utf8String) 
        userPasscode(754),              -- (...Utf8String) 
        userAlias(755),                 -- (...Utf8String) 
        userLoginDate(756),             -- (DateAndTime) 
        userLogoutDate(757),            -- (DateAndTime) 
        userDescription(760),           -- (...Utf8String) 
        userLocation(761),              -- (...Utf8String) 
        --  Button Dial directory attributes (integer-valued) 
        -- 
        buttonDialIndex(800),           -- (xcmCommsDirRecordIndex) 
        buttonDialGroupIndex(801),      -- (xcmCommsDirRecordIndex) 
        --  Button Dial directory attributes (string-valued) 
        -- 
        buttonDialName(850),            -- (...Utf8String) 
        buttonDialFullName(851),        -- (...Utf8String) 
        buttonDialCode(852),            -- (...Utf8String) 
        buttonDialDescription(860),     -- (...Utf8String) 
        buttonDialLocation(861),        -- (...Utf8String) 
        --  Repository directory attributes (integer-valued) 
        -- 
        repositoryIndex(900),           -- (xcmCommsDirRecordIndex) 
        repositoryGroupIndex(901),      -- (xcmCommsDirRecordIndex) 
        repositoryPosixRights(902),     -- (XcmSecPosixRights) 
        repositoryPosixVerbs(903),      -- (XcmSecPosixVerbs) 
        repositorySkill(911),           -- (XcmSecUserSkill) 
        repositoryScope(912),           -- (XcmSecAccountScope) 
        --  Repository directory attributes (string-valued) 
        -- 
        repositoryName(950),            -- (...Utf8String) 
        repositoryFullName(951),        -- (...Utf8String) 
        repositoryCode(952),            -- (...Utf8String) 
        repositoryPassword(953),        -- (...Utf8String) 
        repositoryPasscode(954),        -- (...Utf8String) 
        repositoryAlias(955),           -- (...Utf8String) 
        repositoryLoginDate(956),       -- (DateAndTime) 
        repositoryLogoutDate(957),      -- (DateAndTime) 
        repositoryDescription(960),     -- (...Utf8String) 
        repositoryLocation(961),        -- (...Utf8String) 
        --  Protocol directory attributes (integer-valued) 
        -- 
        --  Conformance:  'protocolType' attributes SHALL 
        --  have protocol type in 'xcmCommsDirAttributeValue' (integer),
        --  as an enumerated type from 'XcmCommsStackExtProtocol' 
        --  defined in the XCMI Comms Engine MIB. 
        --  Other 'protocolXxx' (integer) attributes SHALL have 
        --  protocol type in a parallel 'protocolType' base row. 
        -- 
        protocolType(1000),             -- (XcmCommsStackExtProtocol) 
        protocolPurpose(1001),          -- (XcmCommsStackExtPurpose) 

XCMI Working Group                File 52conftc                [Page 17]

Xerox Common Management Interface (XCMI) Standard               04/14/23

        protocolRole(1002),             -- (XcmCommsStackExtRole) 
        protocolSuite(1003),            -- (XcmCommsStackExtSuite) 
        protocolLayer(1004),            -- (XcmCommsStackExtLayer) 
        protocolDeviceIndex(1010),      -- (hrDeviceIndex) 
        protocolInterfaceIndex(1011),   -- (ifIndex) 
        protocolPriority(1030),         -- (xcmSvcMonServicePriority) 
        protocolConnectorType(1510),    -- (xcmCOOsilanConnectorType) 
        protocolConnectorAdaptive(1511),-- (TruthValue) 
        protocolSignalType(1512),       -- (xcmCOOsilanSignalType) 
        protocolSignalAdaptive(1513),   -- (TruthValue) 
        protocolCableType(1514),        -- (xcmCOOsilanCableType) 
        protocolCableAdaptive(1515),    -- (TruthValue) 
        protocolFrameType(1520),        -- (xcmCOOsilanFrameType) 
        protocolFrameAdaptive(1521),    -- (TruthValue) 
        protocolMinFrameSize(1522),     -- (Ordinal32) 
        protocolMaxFrameSize(1523),     -- (Ordinal32) 
        protocolSpeed(1530),            -- (ifSpeed) 
        protocolSpeedAdaptive(1531),    -- (TruthValue) 
        protocolMinSpeed(1532),         -- (ifSpeed) 
        protocolMaxSpeed(1533),         -- (ifSpeed) 
        protocolBidirectional(1534),    -- (TruthValue) 
        protocolDirection(1535),        -- (xcmCOOsiwanDirection) 
        protocolFlowControl(1536),      -- (TruthValue) 
        protocolMaxConnections(1537),   -- (Cardinal32) 
        protocolInputTimeout(1540),     -- (Cardinal32) - seconds 
        protocolInputFlowWindow(1541),  -- (Ordinal32) 
        protocolInputPrime(1542),       -- (TruthValue) 
        protocolMinInputChars(1543),    -- (Cardinal32) 
        protocolMaxInputChars(1544),    -- (Cardinal32) 
        protocolOutputTimeout(1550),    -- (Cardinal32) - seconds 
        protocolOutputFlowWindow(1551), -- (Ordinal32) 
        protocolOutputPrime(1552),      -- (TruthValue) 
        protocolMinOutputChars(1553),   -- (Cardinal32) 
        protocolMaxOutputChars(1554),   -- (Cardinal32) 
        protocolMaxRetries(1560),       -- (Cardinal32) 
        protocolRetryInterval(1561),    -- (Cardinal32) - seconds 
        protocolPollInterval(1562),     -- (Cardinal32) - seconds 
        protocolListen(1570),           -- (TruthValue) 
        protocolListenSocket(1571),     -- (Ordinal32) 
        protocolListenInterval(1572),   -- (Cardinal32) - seconds 
        protocolSpool(1580),            -- (TruthValue) 
        protocolMaxSpool(1581),         -- (Cardinal32) 
        protocolJobTimeout(1582),       -- (Cardinal32) - seconds 
        protocolAutoSwitch(1583),       -- (xcmCODirectPrintProtocol) 
        protocolBinaryPS(1584),         -- (TruthValue) 
        protocolDefaultPDL(1585),       -- (XcmPrtInterpreterLangFamily)
        protocolSendStartTime(1590),    -- (XcmHrDevCalendarTimeOfDay) 
        protocolSendEndTime(1591),      -- (XcmHrDevCalendarTimeOfDay) 
        protocolReceiveStartTime(1592), -- (XcmHrDevCalendarTimeOfDay) 
        protocolReceiveEndTime(1593),   -- (XcmHrDevCalendarTimeOfDay) 
        protocolSendLineNumber(1600),   -- (xcmCOOsiwanLineNumber) 
        protocolSendCoverSheet(1601),   -- (TruthValue) 
        protocolSendHeader(1602),       -- (TruthValue) 
        protocolSendConfirmPrint(1603), -- (TruthValue) 

XCMI Working Group                File 52conftc                [Page 18]

Xerox Common Management Interface (XCMI) Standard               04/14/23

        protocolSendManual(1604),       -- (TruthValue) 
        protocolSendSecurity(1605),     -- (TruthValue) 
        protocolSendStoreTime(1606),    -- (Cardinal32) - seconds 
        protocolSendResolution(1610),   -- (Cardinal32) - dots/inch 
        protocolSendErrorCorrection(1611),      -- (TruthValue) 
        protocolReceiveLineNumber(1620),-- (xcmCOOsiwanLineNumber) 
        protocolReceiveCoverSheet(1621),-- (TruthValue) 
        protocolReceiveFooter(1622),    -- (TruthValue) 
        protocolReceiveToMemory(1623),  -- (TruthValue) 
        protocolReceiveManual(1624),    -- (TruthValue) 
        protocolReceiveSecurity(1625),  -- (TruthValue) 
        protocolReceiveAutoReduce(1626),-- (TruthValue) 
        protocolReceiveOverflow(1627),  -- (TruthValue) 
        protocolReceiveCollate(1628),   -- (TruthValue) 
        protocolReceiveResolution(1630),-- (Cardinal32) - dots/inch 
        protocolReceiveErrorCorrection(1631),   -- (TruthValue) 
        --  Protocol directory attributes (string-valued) 
        -- 
        --  Conformance:  'protocolTypedXxx' attributes SHALL 
        --  have protocol type in 'xcmCommsDirAttributeValue' (integer),
        --  as an enumerated type from 'XcmCommsStackExtProtocol' 
        --  defined in the XCMI Comms Engine MIB. 
        -- 
        protocolTypedName(2000),                -- (...Utf8String) 
        protocolTypedFullName(2001),            -- (...Utf8String) 
        protocolTypedPassword(2002),            -- (...Utf8String) 
        protocolTypedHostName(2003),            -- (...Utf8String) 
        protocolTypedQueueName(2004),           -- (...Utf8String) 
        protocolTypedServerName(2005),          -- (...Utf8String) 
        protocolTypedDescription(2006),         -- (...Utf8String) 
        protocolTypedLocation(2007),            -- (...Utf8String) 
        protocolTypedAddress(2010),             -- (...Utf8String) 
        protocolTypedBroadcastAddress(2011),    -- (...Utf8String) 
        protocolTypedListenAddress(2012),       -- (...Utf8String) 
        protocolTypedMulticastAddress(2013),    -- (...Utf8String) 
        protocolTypedConfirmAddress(2014),      -- (...Utf8String) 
        protocolTypedConfirmURL(2015),          -- (...Utf8String) 
        protocolTypedAcceptAddress(2020),       -- (...Utf8String) 
        protocolTypedAcceptSubnet(2021),        -- (...Utf8String) 
        protocolTypedRejectAddress(2022),       -- (...Utf8String) 
        protocolTypedRejectSubnet(2023),        -- (...Utf8String) 
        protocolTypedURC(2030),                 -- (...Utf8String) 
        protocolTypedURI(2031),                 -- (...Utf8String) 
        protocolTypedURL(2032),                 -- (...Utf8String) 
        protocolTypedURN(2033),                 -- (...Utf8String) 
        protocolTypedDeviceName(2040),          -- (...Utf8String) 
        reserved(3000) 
    } 







XCMI Working Group                File 52conftc                [Page 19]

Xerox Common Management Interface (XCMI) Standard               04/14/23

XcmCommsLDAPAttributeType ::= TEXTUAL-CONVENTION 
    STATUS      current 
    DESCRIPTION 
        "The type of LDAP attribute stored in this communications, 
        device, or service detail conceptual row. 

        Usage:  Conforming XCMI management stations and agents SHALL 
        encode LDAP attributes as UTF-8 strings (like SLPv2, RFC 2608). 
        - Integers SHALL be encoded as (signed) decimal strings. 
        - Booleans SHALL be encoded as 'true' or 'false' strings. 
        - Binary data (e.g., 'userCertificate') SHALL be stored 
        in SLPv2 opaque encoding (leading '\FF' and escaped octets)." 
    REFERENCE 
        "See:   'xcmCOInternetLDAPAttributeStr' 
                in XCMI Comms Config TC. 
        See:    'systemDirectoryLDAPObjectClass' and 
                'systemDirectoryLDAPAttribute' in XCMI Svc Mon TC. 
        See:    Section 5 'Service Attributes' in 
                Service Location Protocol v2 (RFC 2608). 
        See:    Section 9 'Attribute Types' in 
                COSINE and Internet X.500 Schema (RFC 1274). 
        See:    Section 5 'Attribute Types' in 
                Summary of X.500:1996 User Schema for LDAPv3 (RFC 2256).
        See:    Section 9.1 'Attribute Types' in 
                Definition of inetOrgPerson LDAP Class (RFC 2798)." 
    SYNTAX      INTEGER { 
        other(1), 
        unknown(2), 

        --  ITU-T X.520 Directory Attributes 
        --  (see section 5 'Attribute Types' in RFC 2256) 
        --  (LDAP Attribute OIDs are '2.5.4.x', where x = attrType) 
        --  (see section 7.7 'person', 7.8 'organizationalPerson', and 
        --  7.11 'residentialPerson' in RFC 2256) 
        commonName(3),                  -- 'cn' - common name string 
        surname(4),                     -- 'sn' - family name string 
        serialNumber(5),                -- device serial number string 
        country(6),                     -- 'c' - country (ISO 3166) 
        city(7),                        -- 'l' - locality or region 
        state(8),                       -- 'st' - state or province 
        streetAddress(9),               -- 'street' - physical address 
        org(10),                        -- 'o' - organization name 
        orgUnit(11),                    -- 'ou' - organization unit 
        title(12),                      -- organizational title 
                                        -- see 'userClass' and 
                                        -- 'personalTitle' 
        description(13),                -- description of object 
        searchGuide(14),                -- search guide - OBSOLETE 
        businessCategory(15),           -- business type of organization
        postalAddress(16),              -- postal delivery address 
        postalCode(17),                 -- postal code (aka ZIP code) 
        postOfficeBox(18),              -- post office box 
        office(19),                     -- 'physicalDeliveryOfficeName' 
        telephoneNumber(20),            -- ITU-T E.164 format (RFC 2806)

XCMI Working Group                File 52conftc                [Page 20]

Xerox Common Management Interface (XCMI) Standard               04/14/23

        telexNumber(21),                -- ITU-T Telex number 
        teletexTerminal(22),            -- ITU-T Teletex terminal id 
        faxNumber(23),                  -- ITU-T T.series Fax (RFC 2806)
        x121Address(24),                -- ITU-T X.121 address 
        isdnNumber(25),                 -- 'internationalISDNNumber' 
        registeredAddress(26),          -- for telegrams and expedited 
        destinationIndicator(27),       -- for telegram service 
        preferredDeliveryMethod(28),    -- preference for delivery 
        presentationAddress(29),        -- ISO OSI presentation address 
        supportedContext(30),           -- ISO OSI application contexts 
        member(31),                     -- member distinguished name 
        owner(32),                      -- owner distinguished name 
        role(33),                       -- 'roleOccupant' - role DN 
        seeAlso(34),                    -- see also distinguished name 
        userPassword(35),               -- user password (MUST encrypt) 
        userCertificate(36),            -- user certificate or URL 
        caCertificate(37),              -- CA certificate or URL 
        authorityRevocationList(38),    -- authority rev list or URL 
        certificateRevocationList(39),  -- certificate rev list or URL 
        crossCertificatePair(40),       -- cross certificate pair 
        name(41),                       -- base type - NOT used 
        givenName(42),                  -- first name string 
        initials(43),                   -- initials (without surname) 
        generationQualifier(44),        -- generation (e.g., "IInd") 
        x500UniqueIdentifier(45),       -- X.500 unique id (see 'uid') 
        dnQualifier(46),                -- relative DN qualifier 
        enhancedSearchGuide(47),        -- X.500 client search filters 
        protocolInformation(48),        -- additional ISO OSI address 
        distinguishedName(49),          -- base type - NOT used 
        uniqueMember(50),               -- X.500 unique member (???) 
        houseIdentifier(51),            -- building id within location 
        supportedAlgorithms(52),        -- ISO OSI supported algorithms 
        deltaRevocationList(53),        -- delta rev list or URL 
        dmdName(54),                    -- mgmt domain admin authority 

        --  Selected COSINE and Internet X.500 Attributes 
        --  (see section 9.1.3 'Attributes from RFC 1274' in RFC 2798) 
        --  (see Section 8.3.2 'Pilot Person' in RFC 1274) 
        --  ('pilotPerson' derived from X.521 'person') 
        --  (names below follow RFC 2798 changes to RFC 1274) 
        uid(101),                       -- 'userid' in RFC 1274 
                                        -- (system login name) 
        textEncodedORAddress(102),      -- X.400 O/R address 
                                        -- (historic) 
        mail(103),                      -- 'rfc822Mailbox' in RFC 1274 
                                        -- (RFC 2822/822 format) 
        info(104),                      -- general info 
        favoriteDrink(105),             -- favorite beverage of person 
        roomNumber(106),                -- room number 
        photo(107),                     -- ITU-T T.4 G3 Fax (per X.420) 
        userClass(108),                 -- see 'title' 
        host(109),                      -- host computer 
        manager(110),                   -- manager of an object 
        documentIdentifier(111),        -- document unique id 

XCMI Working Group                File 52conftc                [Page 21]

Xerox Common Management Interface (XCMI) Standard               04/14/23

        documentTitle(112),             -- document title 
        documentVersion(113),           -- document version number 
        documentAuthor(114),            -- document author 
        documentLocation(115),          -- document location 
        homePhone(116),                 -- 'homeTelephoneNumber' 
                                        -- in RFC 1274 (E.164 format) 
        secretary(117),                 -- secretary of a person 
        otherMailbox(118),              -- other than X.400 and RFC 822 
        domainComponent(121),           -- component of a DNS name 
        associatedDomain(127),          -- associated DNS domain 
        associatedName(128),            -- associated DNS name 
        homePostalAddress(129),         -- home postal address 
        personalTitle(130),             -- personal title - see 'title' 
        mobile(131),                    -- 'mobileTelephoneNumber' 
                                        -- in RFC 1274 (E.164 format) 
        pager(132),                     -- 'pagerTelephoneNumber' 
                                        -- in RFC 1274 (E.164 format) 
        friendlyCountry(133),           -- friendly (readable) country 
        uniqueIdentifier(134),          -- unique id for an object 
        orgStatus(135),                 -- 'organizationalStatus' 
        buildingName(138),              -- building name of org or unit 
        personalSignature(143),         -- ITU-T T.4 G3 Fax (per X.420) 
        audio(145),                     -- audio data 
                                        -- (historic) 
        documentPublisher(146),         -- document publisher 

        --  'inetOrgPerson' Object Class Attributes 
        --  (see section 9.1 'Attribute Types' in RFC 2798) 
        --  ('inetOrgPerson' derived from X.521 'organizationalPerson') 
        carLicense(201),                -- vehicle license plate 
        departmentNumber(202),          -- dept id within organization 
        displayName(203),               -- preferred name of person 
        employeeNumber(204),            -- employee number w/in org 
        employeeType(205),              -- employee type w/in org 
        jpegPhoto(206),                 -- JPEG photo 
                                        -- (historic) 
        preferredLanguage(207),         -- preferred language (RFC 3066)
        userSMIMECertificate(208),      -- signed message for S/MIME 
        userPKCS12(209),                -- PKCS #12 for personal id info

        --  URI Attributes 
        --  (see definition of 'labeledURI' in RFC 2079) 
        --  ('labeledURI' is MAY in 'inetOrgPerson' class in RFC 2798) 
        labeledURI(300)                 -- URI (RFC 2396/2732 format) 
    } 

-- 
--          Special Comms Option Types 
-- 

xcmCOSpecialTypes OBJECT-IDENTITY 
    STATUS      current 
    DESCRIPTION 
        "The root of all special comms option types defined in 

XCMI Working Group                File 52conftc                [Page 22]

Xerox Common Management Interface (XCMI) Standard               04/14/23

        the Comms Config TC." 
    ::= { xcmCommsConfigTC 4 } 

xcmCOSpecialLabel OBJECT-IDENTITY 
--  SYNTAX      stringLocalization 
    STATUS      current 
    DESCRIPTION 
        "Human-readable name for the following configuration subtree, 
        specified in 'xcmCommsOptionsValueString'. 

        Usage:  To label tree vertices (eg, for client GUI)." 
    ::= { xcmCOSpecialTypes 1 } 

xcmCOSpecialImport OBJECT-IDENTITY 
--  SYNTAX      integerIndex 
    STATUS      current 
    DESCRIPTION 
        "The 'xcmCommsOptionIndex' of an 'imported' configuration 
        subtree, specified in 'xcmCommsOptionValueInteger'. 

        Usage:  To import a section of common config from elsewhere. 
        All comms configuration options in the 'imported' subtree SHALL 
        be 'imported' and THEN any dependent options found via the 
        current 'xcmCommsOptionFamilyIndex' chain SHALL be treated as 
        though they logically 'followed' the 'imported' configuration 
        subtree. 

        Usage:  This row SHALL be logically 're-typed' by inheritance 
        from the first imported row (eg, 'xcmCOOsilanEthernet'), but 
        ONLY for the 'scoping' of dependent options which are found via 
        the current 'xcmCommsOptionFamilyIndex' chain (eg, a dependent 
        option for 'xcmCOOsilanEthernetFrameOverride'). 

        Usage:  The pointer specified in 'xcmCommsOptionValueInteger' 
        SHALL be used to evaluate the 'imported' configuration substree 
        and THEN any 'local' options SHALL be evaluated from the current
        'xcmCommsOptionFamilyIndex' chain. 

        Usage:  As would normally be true of any option, this row SHALL 
        NOT affect the 'scoping' of independent options found via the 
        current 'xcmCommsOptionNextIndex' chain (eg, the next protocol 
        within a given protocol suite configuration subtree)." 
    ::= { xcmCOSpecialTypes 2 } 

xcmCOSpecialRemark OBJECT-IDENTITY 
--  SYNTAX      stringLocalization 
    STATUS      current 
    DESCRIPTION 
        "Human-readable remark for the following configuration subtree, 
        specified in 'xcmCommsOptionsValueString'. 

        Usage:  To comment tree vertices (eg, for client GUI)." 
    ::= { xcmCOSpecialTypes 3 } 


XCMI Working Group                File 52conftc                [Page 23]

Xerox Common Management Interface (XCMI) Standard               04/14/23


xcmCOSpecialAddress OBJECT-IDENTITY 
--  SYNTAX      stringLocalization 
    STATUS      current 
    DESCRIPTION 
        "Human-readable canonical address for the protocol specified in 
        'xcmCommsOptionValueOID' (eg, 'xcmCOInternetIP') is specified 
        in 'xcmCommsOptionsValueString' (eg, '19.242.128.21'). 

        Usage:  'Overloads' protocol types to yield protocol addresses."
    ::= { xcmCOSpecialTypes 4 } 

xcmCOSpecialState OBJECT-IDENTITY 
--  SYNTAX      XcmCommsMmgtState 
    STATUS      current 
    DESCRIPTION 
        "The current state of the communications protocol specified 
        in 'xcmCommsOptionValueOID' (eg, 'xcmCOInternetIP') is specified
        in 'xcmCommsOptionsValueInteger' (eg, 'opened(9)'). 

        Usage:  'Overloads' protocol types to yield protocol entity 
        states." 
    REFERENCE 
        "See:   'XcmCommsMgmtState' in XCMI Comms Engine TC." 
    ::= { xcmCOSpecialTypes 5 } 

xcmCOSpecialConditions OBJECT-IDENTITY 
--  SYNTAX      XcmCommsMmgtConditions 
    STATUS      current 
    DESCRIPTION 
        "The current conditions of the communications protocol specified
        in 'xcmCommsOptionValueOID' (eg, 'xcmCOInternetIP') is specified
        in 'xcmCommsOptionsValueInteger' (eg, 'openInProgress'). 

        Usage:  'Overloads' protocol types to yield protocol entity 
        conditions." 
    REFERENCE 
        "See:   'XcmCommsMgmtConditions' in XCMI Comms Engine TC." 
    ::= { xcmCOSpecialTypes 6 } 

xcmCOSpecialName OBJECT-IDENTITY 
--  SYNTAX      stringLocalization 
    STATUS      current 
    DESCRIPTION 
        "Human-readable directory name for the directory specified in 
        'xcmCommsOptionValueOID' (eg, 'xcmCOInternetDNS') is specified 
        in 'xcmCommsOptionsValueString' (eg, 'showstopper.sample.com'). 

        Usage:  'Overloads' directory types to yield directory names." 
    ::= { xcmCOSpecialTypes 7 } 

xcmCOSpecialSupportedInteger OBJECT-IDENTITY 
--  SYNTAX      integerNumber 
    STATUS      current 

XCMI Working Group                File 52conftc                [Page 24]

Xerox Common Management Interface (XCMI) Standard               04/14/23

    DESCRIPTION 
        "Integer-encoded supported value for the option specified in 
        'xcmCommsOptionValueOID' (eg, 'xcmCOOsilanFrameType') is found 
        in 'xcmCommsOptionsValueInteger' (eg, 'mac(3)'). 

        Usage:  'Overloads' option types to yield options supported." 
    ::= { xcmCOSpecialTypes 8 } 

xcmCOSpecialSupportedString OBJECT-IDENTITY 
--  SYNTAX      stringLocalization 
    STATUS      current 
    DESCRIPTION 
        "String-encoded supported value for the option specified in 
        'xcmCommsOptionValueOID' (eg, 'xcmCOAppletalkNBPType') is found 
        in 'xcmCommsOptionsValueString' (eg, 'LaserPrinter'). 

        Usage:  'Overloads' option types to yield options supported." 
    ::= { xcmCOSpecialTypes 9 } 

xcmCOSpecialAcceptAddress OBJECT-IDENTITY 
--  SYNTAX      stringLocalization 
    STATUS      current 
    DESCRIPTION 
        "Human-readable 'accept' address for the protocol specified in 
        'xcmCommsOptionValueOID' (eg, 'xcmCOInternetIP') is specified 
        in 'xcmCommsOptionsValueString' (eg, '19.242.128.21'). 

        Usage:  'Overloads' protocol types to yield protocol specific 
        addresses of remote entities at this protocol layer, 
        from which incoming datagrams and/or connections SHALL 
        be accepted. 

        Usage:  Address format is the protocol specific canonical 
        format defined for this protocol type as defined elsewhere in 
        this XCMI Comms Config TC." 
    ::= { xcmCOSpecialTypes 10 } 

xcmCOSpecialAcceptSubnet OBJECT-IDENTITY 
--  SYNTAX      stringLocalization 
    STATUS      current 
    DESCRIPTION 
        "Human-readable 'accept' subnet for the protocol specified in 
        'xcmCommsOptionValueOID' (eg, 'xcmCOInternetIP') is specified 
        in 'xcmCommsOptionsValueString' (eg, '19.242.255.255' as might 
        be specified in an 'xcmCOInternetIPSubnetMask' comms option). 

        Usage:  'Overloads' protocol types to yield protocol specific 
        subnet masks of remote entities at this protocol layer, 
        from which incoming datagrams and/or connections SHALL 
        be accepted. 

        Usage:  Subnet mask format is the protocol specific canonical 
        format defined for this protocol type as defined elsewhere in 
        this XCMI Comms Config TC." 

XCMI Working Group                File 52conftc                [Page 25]

Xerox Common Management Interface (XCMI) Standard               04/14/23

    ::= { xcmCOSpecialTypes 11 } 

xcmCOSpecialRejectAddress OBJECT-IDENTITY 
--  SYNTAX      stringLocalization 
    STATUS      current 
    DESCRIPTION 
        "Human-readable 'reject' address for the protocol specified in 
        'xcmCommsOptionValueOID' (eg, 'xcmCOInternetIP') is specified 
        in 'xcmCommsOptionsValueString' (eg, '19.242.128.21'). 

        Usage:  'Overloads' protocol types to yield protocol specific 
        addresses of remote entities at this protocol layer, 
        from which incoming datagrams and/or connections SHALL 
        be rejected. 

        Usage:  Address format is the protocol specific canonical 
        format defined for this protocol type as defined elsewhere in 
        this XCMI Comms Config TC." 
    ::= { xcmCOSpecialTypes 12 } 

xcmCOSpecialRejectSubnet OBJECT-IDENTITY 
--  SYNTAX      stringLocalization 
    STATUS      current 
    DESCRIPTION 
        "Human-readable 'reject' subnet for the protocol specified in 
        'xcmCommsOptionValueOID' (eg, 'xcmCOInternetIP') is specified 
        in 'xcmCommsOptionsValueString' (eg, '19.242.255.255' as might 
        be specified in an 'xcmCOInternetIPSubnetMask' comms option). 

        Usage:  'Overloads' protocol types to yield protocol specific 
        subnet masks of remote entities at this protocol layer, 
        from which incoming datagrams and/or connections SHALL 
        be rejected. 

        Usage:  Subnet mask format is the protocol specific canonical 
        format defined for this protocol type as defined elsewhere in 
        this XCMI Comms Config TC." 
    ::= { xcmCOSpecialTypes 13 } 

xcmCOSpecialMaxRequestRetries OBJECT-IDENTITY 
--  SYNTAX      Cardinal32 - retries 
    STATUS      current 
    DESCRIPTION 
        "The maximum request retries for the communications protocol 
        specified in 'xcmCommsOptionValueOID' (eg, 'xcmCOInternetDNS') 
        is specified in 'xcmCommsOptionsValueInteger' (eg, '4' retries).

        Usage:  A value of zero indicates that the request SHALL ONLY be
        attempted once (no retries) before being considered a failure. 

        Usage:  'Overloads' protocol types to yield protocol request 
        retry limits." 
    ::= { xcmCOSpecialTypes 14 } 


XCMI Working Group                File 52conftc                [Page 26]

Xerox Common Management Interface (XCMI) Standard               04/14/23


xcmCOSpecialRequestTimeout OBJECT-IDENTITY 
--  SYNTAX      Cardinal32 - seconds 
    STATUS      current 
    DESCRIPTION 
        "The request timeout for the communications protocol 
        specified in 'xcmCommsOptionValueOID' (eg, 'xcmCOInternetDNS') 
        is specified in 'xcmCommsOptionsValueInteger' (eg, '3' seconds).

        Usage:  A value of zero indicates that the request timeout is a 
        local system default (and NOT reported/configured). 

        Usage:  'Overloads' protocol types to yield protocol request 
        timeout limits." 
    ::= { xcmCOSpecialTypes 15 } 

xcmCOSpecialSecurity OBJECT-IDENTITY 
--  SYNTAX      TruthValue - protocol enable/disable 
    STATUS      current 
    DESCRIPTION 
        "The security protocol (datalink, network, transport layer, etc)
        specified in 'xcmCommsOptionValueOID' (eg, 'xcmCOInternetTLS') 
        is enabled and disabled by 'xcmCommsOptionsValueInteger'. 

        Usage:  'Overloads' protocol types to configure security for 
        datalink, network, transport, and application layer protocols." 
    ::= { xcmCOSpecialTypes 16 } 

-- 
--          OSI LAN Protocol Suite 
-- 

xcmCOOsilanSuite 
    OBJECT IDENTIFIER ::= { xcmCommsConfigTC 11 } 
    -- integerTruthValue 

xcmCOOsilanPhysicals 
    OBJECT IDENTIFIER ::= { xcmCOOsilanSuite 1100 } 
    -- integerTruthValue 
xcmCOOsilanConnectorType        -- OSI LAN Connector Type 
    OBJECT IDENTIFIER ::= { xcmCOOsilanPhysicals 1 } 
    -- integerEnum (1=none, 2=other, 3=rj11, 4=rj45, 5=db9, 
    -- 6=bnc, 7=aui, 8=sma, 9=rg48) 
xcmCOOsilanConnectorOverride    -- OSI LAN Connector Type Override 
    OBJECT IDENTIFIER ::= { xcmCOOsilanConnectorType 1 } 
    -- integerEnum (see 'xcmCOOsilanConnectorType' above) 
xcmCOOsilanConnectorDetected    -- OSI LAN Connector Type Detected 
    OBJECT IDENTIFIER ::= { xcmCOOsilanConnectorType 2 } 
    -- integerEnum (see 'xcmCOOsilanConnectorType' above) 
xcmCOOsilanConnectorAdaptive    -- OSI LAN Connector Type Adaptive 
    OBJECT IDENTIFIER ::= { xcmCOOsilanConnectorType 3 } 
    -- integerTruthValue 
xcmCOOsilanSignalType           -- OSI LAN Signal Type 
    OBJECT IDENTIFIER ::= { xcmCOOsilanPhysicals 2 } 

XCMI Working Group                File 52conftc                [Page 27]

Xerox Common Management Interface (XCMI) Standard               04/14/23

    -- integerEnum  
    -- (1=none,  
    --  2=other, 
    --  3=10baseT, 4=10base2, 5=10base5, 6=10baseFL, - Standard Ethernet
    -- 
    --  7=100base-TX (HalfDuplex),                   - Fast Ethernet  
    --       (This is used for fast ethernet half duplex.  
    --         It can be used for 100base-T, 100base-T2, 100base-T4,  
    --                            100base-TX, 100base-FX, etc.) 
    -- 
    --  8=100base-TX (FullDuplex),                   - Fast Ethernet  
    --      (This is used for fast ethernet full duplex.  
    --        It can be used for 100base-T, 100base-T2, 100base-T4,  
    --                           100base-TX, 100base-FX, etc.) 
    -- 
    --  9=4mbTokenRing, 10=16mbTokenRing,            - Token Ring 
    --  11=100mbTokenRing,                           - Fast Token Ring 
    --  12=10baseT (HalfDuplex),  
    --  13=10baseT (FullDuplex), 
    -- 
    --  14=1000base-TX (HalfDuplex),                - 1 Gigabit Ethernet
    --         (This is used for gibabit ethernet half duplex.  
    --           It can be used for 1000base-T, 1000base-TX, etc.) 
    -- 
    --  15=1000base-TX (FullDuplex)                 - 1 Gigabit Ethernet
    --         (This is used for gibabit ethernet full duplex.  
    --           It can be used for 1000base-T, 1000base-TX, etc.) 
    -- 
    -- ) 
    -- 
    -- This object identifies the values to be used in  
    -- SignalOverride and SignalDetected. It does not 
    -- specify a row to be returned in the Comms Option Group 
    -- 
    -- This object identifies the values to be used in  
    -- SignalOverride and SignalDetected. It does not 
    -- specify a row to be returned in the Comms Option Group 
xcmCOOsilanSignalOverride       -- OSI LAN Signal Type Override 
    OBJECT IDENTIFIER ::= { xcmCOOsilanSignalType 1 } 
    -- integerEnum (see 'xcmCOOsilanSignalType' above) 
    -- This is the requested signal type 
    -- If SignalAdaptive is true 1=none should be the returned 
    -- because SignalDetected will return the value being used 
    -- This should be implemented as R/W in the Comms Option Group 
xcmCOOsilanSignalDetected       -- OSI LAN Signal Type Detected 
    OBJECT IDENTIFIER ::= { xcmCOOsilanSignalType 2 } 
    -- integerEnum (see 'xcmCOOsilanSignalType' above) 
    -- This is signal type in use 
    -- This should be implemented as R/O in the Comms Option Group 
xcmCOOsilanSignalAdaptive       -- OSI LAN Signal Type Adaptive 
    OBJECT IDENTIFIER ::= { xcmCOOsilanSignalType 3 } 
    -- integerTruthValue 
    -- If true is selected "autodetect" signal type has been selected 
    -- If false is selected the SignalOverride value has been selected 

XCMI Working Group                File 52conftc                [Page 28]

Xerox Common Management Interface (XCMI) Standard               04/14/23

    -- This should be implemented as R/W in the Comms Option Group 
xcmCOOsilanSignalSupport        -- OSI LAN Signal Type Support 
    OBJECT IDENTIFIER ::= { xcmCOOsilanSignalType 4 } 
    -- integerEnum (list of 'xcmCOOsilanSignalType' above) 
xcmCOOsilanSignalCapability        -- OSI LAN Signal Type Capability 
    OBJECT IDENTIFIER ::= { xcmCOOsilanSignalType 5 } 
    -- This bit-mask defines the signal types supported by the device. 
    -- The current set of values (which MAY be extended in the future) 
    -- is given below 
    --        1  10 MB simplex                2**0 
    --        2  10 MB duplex                 2**1 
    --        4  100 MB simplex               2**2 
    --        8  100 MB duplex                2**3 
    --       16  1 GB simplex                 2**4 
    --       32  1 GB duplex                  2**5 
    -- Usage:  The set of supported signal types is specified by 
    -- adding together the various signals.  For example, the value  
    -- 63 indicates that all the signal types are supported and the  
    -- value 3 indicates that 10 MB simplex and 10 MB duplex are  
    -- supported. 
    --      SYNTAX INTEGER (0..2147483647)   
    --          biggest int = 2**31-1 
xcmCOOsilanCableType            -- OSI LAN Cable Type 
    OBJECT IDENTIFIER ::= { xcmCOOsilanPhysicals 3 } 
    -- integerEnum (1=none, 2=other, 
    -- 3=utp, 4=stp, 5=ftp,                         - Twisted Pair 
    -- 6=thinCoax, 7=thickCoax,                     - Coax 
    -- 8=fiber)                                     - Fiber 
xcmCOOsilanCableOverride        -- OSI LAN Cable Type Override 
    OBJECT IDENTIFIER ::= { xcmCOOsilanCableType 1 } 
    -- integerEnum (see 'xcmCOOsilanCableType' above) 
xcmCOOsilanCableDetected        -- OSI LAN Cable Type Detected 
    OBJECT IDENTIFIER ::= { xcmCOOsilanCableType 2 } 
    -- integerEnum (see 'xcmCOOsilanCableType' above) 
xcmCOOsilanCableAdaptive        -- OSI LAN Cable Type Adaptive 
    OBJECT IDENTIFIER ::= { xcmCOOsilanCableType 3 } 
    -- integerTruthValue 
xcmCOOsilanCableSupport         -- OSI LAN Cable Type Support 
    OBJECT IDENTIFIER ::= { xcmCOOsilanCableType 4 } 
    -- integerEnum (list of 'xcmCOOsilanCableType' above) 

xcmCOOsilanDatalinks 
    OBJECT IDENTIFIER ::= { xcmCOOsilanSuite 1200 } 
    -- integerTruthValue (w/ chain of 'xcmCOOsilan...') 
xcmCOOsilanFrameType            -- OSI LAN Frame Type 
    OBJECT IDENTIFIER ::= { xcmCOOsilanSuite 1201 } 
    -- integerEnum (1=llc, 2=snap, 3=mac, 4=ethernetII, 5=adaptive) 
    -- (Ethernet [IEEE 802.3] supports all five of above frame types) 
    -- (ALL others [IEEE 802.x] support ONLY llc, snap, or adaptive) 
    -- ('adaptive' obsoleted by 'xcmCOOsilanFrameTypeAdaptive' below) 
xcmCOOsilanFrameOverride        -- OSI LAN Frame Type Override 
    OBJECT IDENTIFIER ::= { xcmCOOsilanFrameType 1 } 
    -- integerEnum (see 'xcmCOOsilanFrameType' above) 
xcmCOOsilanFrameDetected        -- OSI LAN Frame Type Detected 

XCMI Working Group                File 52conftc                [Page 29]

Xerox Common Management Interface (XCMI) Standard               04/14/23

    OBJECT IDENTIFIER ::= { xcmCOOsilanFrameType 2 } 
    -- integerEnum (see 'xcmCOOsilanFrameType' above) 
xcmCOOsilanFrameAdaptive        -- OSI LAN Frame Type Adaptive 
    OBJECT IDENTIFIER ::= { xcmCOOsilanFrameType 3 } 
    -- integerTruthValue 
    -- (obsoletes 'adaptive' in 'xcmCOOsilanFrameType' above) 
xcmCOOsilanEthernet             -- OSI LAN Ethernet (IEEE 802.3) 
    OBJECT IDENTIFIER ::= { xcmCOOsilanSuite 1203 } 
    -- integerTruthValue 
xcmCOOsilanTokenBus             -- OSI LAN Token Bus (IEEE 802.4) 
    OBJECT IDENTIFIER ::= { xcmCOOsilanSuite 1204 } 
    -- integerTruthValue 
xcmCOOsilanTokenRing            -- OSI LAN Token Ring (IEEE 802.5) 
    OBJECT IDENTIFIER ::= { xcmCOOsilanSuite 1205 } 
    -- integerTruthValue 
xcmCOOsilanFDDI                 -- OSI LAN FDDI 
    OBJECT IDENTIFIER ::= { xcmCOOsilanSuite 1207 } 
    -- integerTruthValue 

xcmCOOsilanEthernetType         -- OSI LAN Ethernet Adapter Type 
    OBJECT IDENTIFIER ::= { xcmCOOsilanEthernet 1 } 
    -- integerEnum (1=none, 2=other, 
    -- 3=integral,                      - adapter on system board 
    -- 4=isa,                           - adapter on ISA interface 
    -- 5=eisa,                          - adapter on EISA interface 
    -- 6=pci,                           - adapter on PCI interface 
    -- 7=pcmcia)                        - adapter on PCMCIA interface 
xcmCOOsilanEthernetDevice 
    OBJECT IDENTIFIER ::= { xcmCOOsilanEthernet 2 } 
    -- integerNumber ('hrDeviceIndex' in IETF HR MIB, or 0=unknown) 
xcmCOOsilanEthernetDeviceName 
    OBJECT IDENTIFIER ::= { xcmCOOsilanEthernetDevice 1 } 
    -- stringLocalization ('xcmHrDevInfoName' in HRX, eg, '/dev/elan1') 
xcmCOOsilanEthernetSpeed 
    OBJECT IDENTIFIER ::= { xcmCOOsilanEthernet 3 } 
    -- integerNumber (as in 'ifSpeed' in IETF MIB-II) 
xcmCOOsilanEthernetSpeedOverride 
    OBJECT IDENTIFIER ::= { xcmCOOsilanEthernetSpeed 1 } 
    -- integerNumber (see 'xcmCOOsilanEthernetSpeed' above) 
xcmCOOsilanEthernetSpeedDetected 
    OBJECT IDENTIFIER ::= { xcmCOOsilanEthernetSpeed 2 } 
    -- integerNumber (see 'xcmCOOsilanEthernetSpeed' above) 
xcmCOOsilanEthernetSpeedAdaptive 
    OBJECT IDENTIFIER ::= { xcmCOOsilanEthernetSpeed 3 } 
    -- integerTruthValue 
xcmCOOsilanEthernetSpeedSupport 
    OBJECT IDENTIFIER ::= { xcmCOOsilanEthernetSpeed 4 } 
    -- integerNumber (as in 'ifSpeed' in IETF MIB-II, list of speeds) 
xcmCOOsilanEthernetMinSpeed 
    OBJECT IDENTIFIER ::= { xcmCOOsilanEthernetSpeed 5 } 
    -- integerNumber (as in 'ifSpeed' in IETF MIB-II) 
xcmCOOsilanEthernetMaxSpeed 
    OBJECT IDENTIFIER ::= { xcmCOOsilanEthernetSpeed 6 } 
    -- integerNumber (as in 'ifSpeed' in IETF MIB-II) 

XCMI Working Group                File 52conftc                [Page 30]

Xerox Common Management Interface (XCMI) Standard               04/14/23

xcmCOOsilanEthernetSpeedPowerSaver 
    OBJECT IDENTIFIER ::= { xcmCOOsilanEthernetSpeed 7 } 
    -- integerNumber (as in 'ifSpeed' in IETF MIB-II) 
xcmCOOsilanEthernetMaxFrameSize 
    OBJECT IDENTIFIER ::= { xcmCOOsilanEthernet 4 } 
    -- integerNumber (as in 'ifMtu' in IETF MIB-II) 
xcmCOOsilanEthernetInterface 
    OBJECT IDENTIFIER ::= { xcmCOOsilanEthernet 5 } 
    -- integerNumber ('ifIndex' in IETF MIB-II, or 0=unknown) 
xcmCOOsilanEthernetMACAddress 
    OBJECT IDENTIFIER ::= { xcmCOOsilanEthernet 6 } 
    -- stringLocalization (hex format, MAC address) 
    -- ([12 octets] - ASCII hex of IEEE 802.x MAC address) 
    -- (MAC address in 'ifPhysAddress' in IETF MIB-II) 

xcmCOOsilanTokenRingType        -- OSI LAN Token Ring Adapter Type 
    OBJECT IDENTIFIER ::= { xcmCOOsilanTokenRing 1 } 
    -- integerEnum (1=none, 2=other, 
    -- 3=integral,                      - adapter on system board 
    -- 4=isa,                           - adapter on ISA interface 
    -- 5=eisa,                          - adapter on EISA interface 
    -- 6=pci,                           - adapter on PCI interface 
    -- 7=pcmcia)                        - adapter on PCMCIA interface 
xcmCOOsilanTokenRingDevice 
    OBJECT IDENTIFIER ::= { xcmCOOsilanTokenRing 2 } 
    -- integerNumber ('hrDeviceIndex' in IETF HR MIB, or 0=unknown) 
xcmCOOsilanTokenRingDeviceName 
    OBJECT IDENTIFIER ::= { xcmCOOsilanTokenRingDevice 1 } 
    -- stringLocalization ('xcmHrDevInfoName' in HRX, eg, '/dev/trlan1')
xcmCOOsilanTokenRingSpeed 
    OBJECT IDENTIFIER ::= { xcmCOOsilanTokenRing 3 } 
    -- integerNumber (as in 'ifSpeed' in IETF MIB-II) 
xcmCOOsilanTokenRingSpeedOverride 
    OBJECT IDENTIFIER ::= { xcmCOOsilanTokenRingSpeed 1 } 
    -- integerNumber (see 'xcmCOOsilanTokenRingSpeed' above) 
xcmCOOsilanTokenRingSpeedDetected 
    OBJECT IDENTIFIER ::= { xcmCOOsilanTokenRingSpeed 2 } 
    -- integerNumber (see 'xcmCOOsilanTokenRingSpeed' above) 
xcmCOOsilanTokenRingSpeedAdaptive 
    OBJECT IDENTIFIER ::= { xcmCOOsilanTokenRingSpeed 3 } 
    -- integerTruthValue 
xcmCOOsilanTokenRingSpeedSupport 
    OBJECT IDENTIFIER ::= { xcmCOOsilanTokenRingSpeed 4 } 
    -- integerNumber (as in 'ifSpeed' in IETF MIB-II, list of speeds) 
xcmCOOsilanTokenRingMinSpeed 
    OBJECT IDENTIFIER ::= { xcmCOOsilanTokenRingSpeed 5 } 
    -- integerNumber (as in 'ifSpeed' in IETF MIB-II) 
xcmCOOsilanTokenRingMaxSpeed 
    OBJECT IDENTIFIER ::= { xcmCOOsilanTokenRingSpeed 6 } 
    -- integerNumber (as in 'ifSpeed' in IETF MIB-II) 
xcmCOOsilanTokenRingMaxFrameSize 
    OBJECT IDENTIFIER ::= { xcmCOOsilanTokenRing 4 } 
    -- integerNumber (as in 'ifMtu' in IETF MIB-II) 
xcmCOOsilanTokenRingInterface 

XCMI Working Group                File 52conftc                [Page 31]

Xerox Common Management Interface (XCMI) Standard               04/14/23

    OBJECT IDENTIFIER ::= { xcmCOOsilanTokenRing 5 } 
    -- integerNumber ('ifIndex' in IETF MIB-II, or 0=unknown) 
xcmCOOsilanTokenRingMACAddress 
    OBJECT IDENTIFIER ::= { xcmCOOsilanTokenRing 6 } 
    -- stringLocalization (hex format, MAC address) 
    -- ([12 octets] - ASCII hex of IEEE 802.x MAC address) 
    -- ('burned in' MAC address, MAY be 'ifPhysAddress' in IETF MIB-II) 
    -- See: 'xcmCOOsilanTokenRingMACOverride' below 
xcmCOOsilanTokenRingSSR         -- OSI LAN Token Ring Source Stn Route 
    OBJECT IDENTIFIER ::= { xcmCOOsilanTokenRing 11 } 
    -- integerTruthValue (true=enableSSR, false=disableSSR) 
    -- See: IBM Token Ring Network Architecture Reference, SC30-3374-01,
    --      page 2-3 'Source Routing', page 2-8 'Broadcast Terminology',
    --      and page 3-8 'Routing Information Field' 
    -- See: 'xcmCOOsilanTokenRing[AllRoute|SingleRR|Adaptive]' below 
xcmCOOsilanTokenRingSSRAllRoute -- OSI LAN Token Ring All Route Request 
    OBJECT IDENTIFIER ::= { xcmCOOsilanTokenRing 12 } 
    -- integerTruthValue (true=allRouteReq, false=singleRouteReq) 
    -- (true specifies send broadcast requests, when SSR is enabled) 
    -- (false specifies send unicast requests, when SSR is enabled) 
xcmCOOsilanTokenRingSSRSingleRR -- OSI LAN Token Ring Single Route Resp 
    OBJECT IDENTIFIER ::= { xcmCOOsilanTokenRing 13 } 
    -- integerTruthValue (true=singleRouteResp, false=allRouteResp) 
    -- (true specifies send unicast responses, when SSR is enabled) 
    -- (false specifies send broadcast responses, when SSR is enabled) 
xcmCOOsilanTokenRingSSRAdaptive -- OSI LAN Token Ring Adaptive 
    OBJECT IDENTIFIER ::= { xcmCOOsilanTokenRing 14 } 
    -- integerTruthValue (true=adaptive, false=static) 
    -- (true specifies sniff local subnetwork, when SSR is enabled) 
    -- (false specifies use 'xcmCOOsilanTokenRing[AllRoute|SingleRR]') 
xcmCOOsilanTokenRingMACOverride -- OSI LAN Token Ring MAC Override 
    OBJECT IDENTIFIER ::= { xcmCOOsilanTokenRing 21 } 
    -- stringLocalization (hex format, MAC address) 
    -- ([12 octets] - ASCII hex of IEEE 802.x MAC address) 
    -- (specifies the local MAC address of this token ring station) 
    -- (MAY be used to override 'burned in' hardware address in 
    -- 'xcmCOOsilanTokenRingMACAddress' and FORCE 'ifPhysAddress') 
    -- See: 'xcmCOOsilanTokenRingMACAddress' above 

-- 
--          OSI WAN Protocol Suite 
-- 

xcmCOOsiwanSuite 
    OBJECT IDENTIFIER ::= { xcmCommsConfigTC 13 } 
    -- integerTruthValue 

xcmCOOsiwanPhysicals 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanSuite 1100 } 
    -- integerTruthValue 
xcmCOOsiwanConnectorType        -- OSI WAN Connector Type 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanPhysicals 1 } 
    -- integerEnum (1=none, 2=other, 3=rj11, 4=rj45) 
xcmCOOsiwanConnectorOverride    -- OSI WAN Connector Type Override 

XCMI Working Group                File 52conftc                [Page 32]

Xerox Common Management Interface (XCMI) Standard               04/14/23

    OBJECT IDENTIFIER ::= { xcmCOOsiwanConnectorType 1 } 
    -- integerEnum (see 'xcmCOOsiwanConnectorType' above) 
xcmCOOsiwanConnectorDetected    -- OSI WAN Connector Type Detected 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanConnectorType 2 } 
    -- integerEnum (see 'xcmCOOsiwanConnectorType' above) 
xcmCOOsiwanConnectorAdaptive    -- OSI WAN Connector Type Adaptive 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanConnectorType 3 } 
    -- integerTruthValue 
xcmCOOsiwanSignalType           -- OSI WAN Signal Type 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanPhysicals 2 } 
    -- integerEnum (1=none, 2=other, 3=tone, 4=pulse) 
xcmCOOsiwanSignalOverride       -- OSI WAN Signal Type Override 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanSignalType 1 } 
    -- integerEnum (see 'xcmCOOsiwanSignalType' above) 
xcmCOOsiwanSignalDetected       -- OSI WAN Signal Type Detected 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanSignalType 2 } 
    -- integerEnum (see 'xcmCOOsiwanSignalType' above) 
xcmCOOsiwanSignalAdaptive       -- OSI WAN Signal Type Adaptive 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanSignalType 3 } 
    -- integerTruthValue 
xcmCOOsiwanSignalSupport        -- OSI WAN Signal Type Support 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanSignalType 4 } 
    -- integerEnum (list of 'xcmCOOsiwanSignalType' above) 
xcmCOOsiwanLineNumber           -- OSI WAN Line Number 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanPhysicals 4 } 
    -- integerNumber (1=default or 1..n) 
xcmCOOsiwanSendManual           -- OSI WAN Receive Manual 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanPhysicals 5 } 
    -- integerTruthValue (true=sendManual, false=sendAuto) 
xcmCOOsiwanReceiveManual        -- OSI WAN Receive Manual 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanPhysicals 6 } 
    -- integerTruthValue (true=receiveManual, false=receiveAuto) 
xcmCOOsiwanRingsBeforeAnswer    -- OSI WAN Rings Before Answer 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanPhysicals 7 } 
    -- integerNumber (1..n) 
xcmCOOsiwanErrorCorrection      -- OSI WAN Error Correction 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanPhysicals 8 } 
    -- integerTruthValue 
xcmCOOsiwanDirection            -- OSI WAN Direction 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanPhysicals 9 } 
    -- integerEnum (1=sendAndReceive, 2=sendOnly, 3=receiveOnly) 
xcmCOOsiwanSendStartTime        -- OSI WAN Send Start Time 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanPhysicals 10 } 
    -- integerNumber (XcmHrDevCalendarTimeOfDay in XCMI HRX TC) 
xcmCOOsiwanSendEndTime          -- OSI WAN Send End Time 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanPhysicals 11 } 
    -- integerNumber (XcmHrDevCalendarTimeOfDay in XCMI HRX TC) 
xcmCOOsiwanReceiveStartTime     -- OSI WAN Receive Start Time 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanPhysicals 12 } 
    -- integerNumber (XcmHrDevCalendarTimeOfDay in XCMI HRX TC) 
xcmCOOsiwanReceiveEndTime       -- OSI WAN Receive End Time 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanPhysicals 13 } 
    -- integerNumber (XcmHrDevCalendarTimeOfDay in XCMI HRX TC) 
xcmCOOsiwanRingerVolume         -- OSI WAN Ringer Volume 

XCMI Working Group                File 52conftc                [Page 33]

Xerox Common Management Interface (XCMI) Standard               04/14/23

    OBJECT IDENTIFIER ::= { xcmCOOsiwanPhysicals 20 } 
    -- integerNumber (0=off, or 1..100) 
xcmCOOsiwanMonitorVolume        -- OSI WAN Monitor Volume 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanPhysicals 21 } 
    -- integerNumber (0=off, or 1..100) 
xcmCOOsiwanAlarmVolume          -- OSI WAN Alarm Volume 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanPhysicals 22 } 
    -- integerNumber (0=off, or 1..100) 
xcmCOOsiwanKeyboardVolume       -- OSI WAN Keyboard Volume 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanPhysicals 23 } 
    -- integerNumber (0=off, or 1..100) 

xcmCOOsiwanDatalinks 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanSuite 1200 } 
    -- integerTruthValue (w/ chain of 'xcmCOOsiwan...') 
xcmCOOsiwanFax                  -- CCITT Fax (facsimile) 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanSuite 1241 } 
    -- integerTruthValue 
xcmCOOsiwanPSTN                 -- CCITT PSTN (analog telephone) 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanSuite 1251 } 
    -- integerTruthValue 
xcmCOOsiwanISDN                 -- CCITT ISDN (digital telephone) 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanSuite 1261 } 
    -- integerTruthValue 

xcmCOOsiwanFaxAddress 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanFax 1 } 
    -- stringLocalization 
xcmCOOsiwanFaxDevice 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanFax 2 } 
    -- integerNumber ('hrDeviceIndex' in IETF HR MIB, or 0=unknown) 
xcmCOOsiwanFaxDeviceName 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanFaxDevice 1 } 
    -- stringLocalization ('xcmHrDevInfoName' in HRX, eg, '/dev/lpr1') 
xcmCOOsiwanFaxSpeed 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanFax 3 } 
    -- integerNumber (as in 'ifSpeed' in IETF MIB-II) 
xcmCOOsiwanFaxSpeedOverride 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanFaxSpeed 1 } 
    -- integerNumber (see 'xcmCOOsiwanFaxSpeed' above) 
xcmCOOsiwanFaxSpeedDetected 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanFaxSpeed 2 } 
    -- integerNumber (see 'xcmCOOsiwanFaxSpeed' above) 
xcmCOOsiwanFaxSpeedAdaptive 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanFaxSpeed 3 } 
    -- integerTruthValue 
xcmCOOsiwanFaxSpeedSupport 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanFaxSpeed 4 } 
    -- integerNumber (as in 'ifSpeed' in IETF MIB-II, list of speeds) 
xcmCOOsiwanFaxMinSpeed 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanFaxSpeed 5 } 
    -- integerNumber (as in 'ifSpeed' in IETF MIB-II) 
xcmCOOsiwanFaxMaxSpeed 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanFaxSpeed 6 } 

XCMI Working Group                File 52conftc                [Page 34]

Xerox Common Management Interface (XCMI) Standard               04/14/23

    -- integerNumber (as in 'ifSpeed' in IETF MIB-II) 
xcmCOOsiwanFaxInterface 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanFax 5 } 
    -- integerNumber ('ifIndex' in IETF MIB-II, or 0=unknown) 
xcmCOOsiwanFaxAcceptAddress     -- CCITT Fax Accept Address (list) 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanFax 11 } 
    -- stringLocalization (used for both send and receive) 
xcmCOOsiwanFaxRejectAddress     -- CCITT Fax Reject Address (list) 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanFax 12 } 
    -- stringLocalization (used for both send and receive) 
xcmCOOsiwanFaxSendCoverSheet    -- CCITT Fax Send Add Cover Sheet 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanFax 20 } 
    -- integerTruthValue 
xcmCOOsiwanFaxSendHeader        -- CCITT Fax Send Add Header 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanFax 21 } 
    -- integerTruthValue 
xcmCOOsiwanFaxSendManual        -- CCITT Fax Send Manual 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanFax 22 } 
    -- integerTruthValue (true=sendManual, false=sendAuto) 
xcmCOOsiwanFaxSendSecurity      -- CCITT Fax Send Security 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanFax 23 } 
    -- integerTruthValue (true=checkRemoteAddress, false=noSecurity) 
xcmCOOsiwanFaxMaxRetries        -- CCITT Fax Send Max Retries 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanFax 24 } 
    -- integerNumber (0=immediate, or 1..n) 
xcmCOOsiwanFaxRetryInterval     -- CCITT Fax Send Retry Interval 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanFax 25 } 
    -- integerNumber (seconds, 0=none, or 1..n) 
xcmCOOsiwanFaxSendStoreTime     -- CCITT Fax Send Store For Later Time 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanFax 26 } 
    -- integerNumber (seconds, 0=discard, or 1..n) 
xcmCOOsiwanFaxMaxOriginalLength -- CCITT Fax Send Max Original Length 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanFax 27 } 
    -- integerNumber (millimeters, 0=infinite, or 1..n) 
xcmCOOsiwanFaxReceiveCoverSheet -- CCITT Fax Receive Add Cover Sheet 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanFax 30 } 
    -- integerTruthValue 
xcmCOOsiwanFaxReceiveFooter     -- CCITT Fax Receive Print Footer 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanFax 31 } 
    -- integerTruthValue 
xcmCOOsiwanFaxReceiveToMemory   -- CCITT Fax Receive To Memory 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanFax 32 } 
    -- integerTruthValue (true=receiveToMemory, false=rejectReceive) 
xcmCOOsiwanFaxReceiveManual     -- CCITT Fax Receive Manual 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanFax 33 } 
    -- integerTruthValue (true=receiveManual, false=receiveAuto) 
xcmCOOsiwanFaxReceiveSecurity   -- CCITT Fax Receive Security 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanFax 34 } 
    -- integerTruthValue (true=checkRemoteAddress, false=noSecurity) 
xcmCOOsiwanFaxReceiveAutoReduce -- CCITT Fax Receive Auto Reduce To Fit 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanFax 35 } 
    -- integerTruthValue (true=autoReduce, false=noAutoReduce) 
xcmCOOsiwanFaxReceiveOverflow   -- CCITT Fax Receive Overflow To Next 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanFax 36 } 

XCMI Working Group                File 52conftc                [Page 35]

Xerox Common Management Interface (XCMI) Standard               04/14/23

    -- integerTruthValue 
xcmCOOsiwanFaxReceiveCollate    -- CCITT Fax Receive Collate 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanFax 37 } 
    -- integerTruthValue 

xcmCOOsiwanFaxG3                -- CCITT Fax G3 Mode 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanFax 40 } 
    -- integerTruthValue (true=enableG3, false=disableG3) 

xcmCOOsiwanFaxG4                -- CCITT Fax G4 Mode 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanFax 41 } 
    -- integerTruthValue (true=enableG4, false=disableG4) 

xcmCOOsiwanFaxLineSwitching     -- CCITT Fax Line Switching 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanFax 42 } 
    -- integerTruthValue (enable/disable internal/external line switch) 

xcmCOOsiwanFaxMaxSpeedDial      -- CCITT Fax Max Speed Dial Entries 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanFax 43 } 
    -- integerNumber (fax max speed dial entries) 
    -- (see - 'XcmCommsDirRecordType' in XCMI TC, especially 
    -- 'recordSpeedDial' and 'recordSpeedDialGroup' records) 
    -- (see - 'XcmCommsDirAttributeType' in XCMI CC TC, especially 
    -- 'service...' and 'speedDial...' attributes) 

xcmCOOsiwanPSTNAddress          -- CCITT PSTN (analog telephone) 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanPSTN 1 } 
    -- stringLocalization 

xcmCOOsiwanISDNAddress          -- CCITT ISDN (digital telephone) 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanISDN 1 } 
    -- stringLocalization 

xcmCOOsiwanTransports 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanSuite 1400 } 
    -- integerTruthValue 

xcmCOOsiwanApplications 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanSuite 1700 } 
    -- integerTruthValue 
xcmCOOsiwanDPA                          -- ISO 10175 (printing) 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanSuite 1713 } 
    -- integerTruthValue 
xcmCOOsiwanFTAM                         -- ISO 8571 (filing) 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanSuite 1714 } 
    -- integerTruthValue 
xcmCOOsiwanVT                           -- ISO 9041 (terminal) 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanSuite 1716 } 
    -- integerTruthValue 
xcmCOOsiwanMHS                          -- CCITT X.400 (email) 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanSuite 1740 } 
    -- integerTruthValue 
xcmCOOsiwanDS                           -- CCITT X.500 (directory) 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanSuite 1750 } 

XCMI Working Group                File 52conftc                [Page 36]

Xerox Common Management Interface (XCMI) Standard               04/14/23

    -- integerTruthValue 
xcmCOOsiwanDAP                          -- CCITT X.500 DAP (access) 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanSuite 1751 } 
    -- integerTruthValue 
xcmCOOsiwanDSP                          -- CCITT X.500 DSP (backbones) 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanSuite 1752 } 
    -- integerTruthValue 
xcmCOOsiwanMgmt                         -- CCITT X.700 (system mgmt) 
    OBJECT IDENTIFIER ::= { xcmCOOsiwanSuite 1770 } 
    -- integerTruthValue 
xcmCOOsiwanCMIP                         -- CCITT X.710/X.711 CMIP (mgmt)
    OBJECT IDENTIFIER ::= { xcmCOOsiwanSuite 1771 } 
    -- integerTruthValue 
xcmCOOsiwanSecurity                     -- CCITT X.800 (system security)
    OBJECT IDENTIFIER ::= { xcmCOOsiwanSuite 1780 } 
    -- integerTruthValue 

-- 
--          Internet Protocol Suite 
-- 

xcmCOInternetSuite 
    OBJECT IDENTIFIER ::= { xcmCommsConfigTC 14 } 
    -- integerTruthValue 

xcmCOInternetDatalinks 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1200 } 
    -- integerTruthValue (w/ chain of 'xcmCOOsilan...') 
    -- (obsoletes 'xcmCOInternetIPDatalinks') 
xcmCOInternetSLIP               -- SLIP (serial datalink) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1201 } 
    -- integerTruthValue 
xcmCOInternetPPP                -- PPP (serial datalink) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1202 } 
    -- integerTruthValue 

xcmCOInternetTransports 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1400 } 
    -- integerTruthValue 
xcmCOInternetIP                 -- IP (CL network) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1301 } 
    -- integerTruthValue 
xcmCOInternetICMP               -- ICMP (layer management - network) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1302 } 
    -- integerTruthValue 
xcmCOInternetARP                -- ARP (routing) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1303 } 
    -- integerTruthValue 
xcmCOInternetDHCP               -- DHCP (routing/boot) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1304 } 
    -- integerTruthValue 
xcmCOInternetBOOTP              -- BOOTP (routing/boot) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1305 } 
    -- integerTruthValue 

XCMI Working Group                File 52conftc                [Page 37]

Xerox Common Management Interface (XCMI) Standard               04/14/23


xcmCOInternetBOOTPBroadcastEnabled 
   OBJECT IDENTIFIER ::= { xcmCOInternetBOOTP 1} 
    -- integerTruthValue (true=enableBOOTPBroadcast,  
    --                    false=disableBOOTPBroadcast) 

xcmCOInternetRARP               -- RARP (routing/boot) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1306 } 
    -- integerTruthValue 
xcmCOInternetIPv6               -- IPv6 (CL Network, RFC 2460) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1310 } 
    -- integerTruthValue 
xcmCOInternetUDP                -- UDP (CL transport) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1401 } 
    -- integerTruthValue 
xcmCOInternetTCP                -- TCP (CO transport) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1402 } 
    -- integerTruthValue 
xcmCOInternetPing               -- Ping (echo) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1404 } 
    -- integerTruthValue 
xcmCOInternetSSL3               -- SSL3 (security) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1405 } 
    -- integerTruthValue 
    -- (Netscape Secure Sockets Layer v3) 
xcmCOInternetTLS                -- TLS (security) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1406 } 
    -- integerTruthValue 
    -- (see RFC 2246, TLS Protocol v1.0, January 1999) 

xcmCOInternetTLSVersionsEnabled   -- TLS (security) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1407 } 
    -- integerEnum 
    -- (1=Enable TLS 1.0 and above, 
    --  2=Enable TLS 1.1 and above, 
    --  3=Enable TLS 1.2 and above, 
    --  4=Enable TLS 1.3) 
    -- (see RFC 2246, TLS Protocol v1.0, January 1999) 
    -- (see RFC 4366, TLS Protocol v1.1, April 2006) 
    -- (see RFC 5246, TLS Protocol v1.2, August 2008) 
    -- (see RFC 8446, TLS Protocol v1.3, August 2018) 

xcmCOInternetTLSVersion13EnableDisable  
    OBJECT IDENTIFIER ::= { xcmCOInternetTLSVersionsEnabled 1 } 
    -- integerTruthValue 

 xcmCOInternetICMPv6               -- ICMPv6 (RFC 2463) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1410 } 
    -- integerTruthValue 

xcmCOInternetSSL3Port               -- SSL3 port number 
    OBJECT IDENTIFIER ::= { xcmCOInternetSSL3 1 } 
    -- integerNumber 


XCMI Working Group                File 52conftc                [Page 38]

Xerox Common Management Interface (XCMI) Standard               04/14/23


xcmCOInternetSSL3CipherStrength        -- SSL3 Cipher Strength 
    OBJECT IDENTIFIER ::= { xcmCOInternetSSL3 2 } 
    -- Cipher encryption strength used to control the set of 
    --  supported ciphers when using SSL (e.g. to enforce  
    --  128-bit or higher encryption keys). 
    -- integerNumber 
    -- 0=custom, 40, 56, 128, 168, 256, etc. 
    -- (e.g. 40 enforces all encryption keys 40-bit or higher, 
    --  128 enforces all encryption keys 128-bit or higher) 
    -- 0=custom allows choice of specific encryption keys 

xcmCOInternetIPAddress          -- IP Node Address 
    OBJECT IDENTIFIER ::= { xcmCOInternetIP 1 } 
    -- stringLocalization (IPv4 - dotted decimal 'a.b.c.d') 
    -- (IPv4 - decimal values [1-3 octets] of four 8-bit components) 
    -- (eg, '13.226.19.10') 

xcmCOInternetIPv6Address          -- IPv6 Node Address 
    OBJECT IDENTIFIER ::= { xcmCOInternetIPv6 1 } 
    -- (IPv6 - eight hex values [0-4 octets] of 16-bit components 
    --  optionally followed by '/' and prefix length [1-3 octets] - 
    --  ASCII decimal of 1-octet prefix length) 
    -- (eg, 'FEDC:BA98:7654:3210/64') 
    -- (see section 2.2 'Textual Representation of Addresses' and 
    --  section 2.3 'Text Representation of Address Prefixes' in 
    -- RFC 2373, IPv6 Addressing Architecture) 
    -- (see section 2 'Literal IPv6 Address Format in URL Syntax' in 
    -- RFC 2732, Format for Literal IPv6 Addresses in URLs) 

xcmCOInternetIPSocketAddress    -- IP Socket Address 
    OBJECT IDENTIFIER ::= { xcmCOInternetIPAddress 1 } 
    -- stringLocalization (IPv4 - dotted decimal 'a.b.c.d:socket') 
    -- (note - in IPv4 ONLY, a dot '.' MAY also be used before 'socket' 
    -- and such use of dot was recommended in XCMI v4.0 and earlier) 
    -- (see 'xcmCOInternetIPAddress' for references) 

xcmCOInternetIPv6SocketAddress    -- IPv6 Socket Address 
    OBJECT IDENTIFIER ::= { xcmCOInternetIPv6Address 1 } 
    -- stringLocalization(IPv6 - hex w/ colons '[x1:...:x8/ppp]:socket')
    -- ('socket' [1-5 octets] - ASCII decimal of 2-octet socket) 
    -- (see 'xcmCOInternetIPv6Address' for references) 

xcmCOInternetIPv6ManuallyAssignedAddress 
    OBJECT IDENTIFIER ::= { xcmCOInternetIPv6Address 2 } 
    -- stringLocalization (IPv6 - hex w/ colons '[x1:...:x8/yyy]') 
    -- (see 'xcmCOInternetIPv6Address' for references) 
    -- Indicates an address that was manually configured, e.g., by user 
    -- configuration. 

xcmCOInternetIPv6DHCPv6AssignedAddress 
    OBJECT IDENTIFIER ::= { xcmCOInternetIPv6Address 3 } 
    -- stringLocalization (IPv6 - hex w/ colons '[x1:...:x8/yyy]') 
    -- (see 'xcmCOInternetIPv6Address' for references) 

XCMI Working Group                File 52conftc                [Page 39]

Xerox Common Management Interface (XCMI) Standard               04/14/23

    -- Indicates an address that was assigned to this system by 
    -- a DHCPv6 server. 

xcmCOInternetIPv6LinkLocalAddress 
    OBJECT IDENTIFIER ::= { xcmCOInternetIPv6Address 4 } 
    -- stringLocalization (IPv6 - hex w/ colons '[x1:...:x8/yyy]') 
    -- (see 'xcmCOInternetIPv6Address' for references) 
    -- Indicates the address created with the link local prefix fe80 
    -- and the EUI-64 interface id by IPv6 stateless auto-configuration.

xcmCOInternetIPv6StatelessAddress 
    OBJECT IDENTIFIER ::= { xcmCOInternetIPv6Address 5 } 
    -- stringLocalization (IPv6 - hex w/ colons '[x1:...:x8/yyy]') 
    -- (see 'xcmCOInternetIPv6Address' for references) 
    -- Indicates an address created by IPv6 stateless 
    -- auto-configuration. 

xcmCOInternetIPv6RandomAddress 
    OBJECT IDENTIFIER ::= { xcmCOInternetIPv6Address 6 } 
    -- stringLocalization (IPv6 - hex w/ colons '[x1:...:x8/yyy]') 
    -- (see 'xcmCOInternetIPv6Address' for references) 
    -- Indicates an address chosen by the system at random, e.g., 
    -- an RFC 3041 privacy address. 

xcmCOInternetIPv6AutomaticAddressing 
    OBJECT IDENTIFIER ::= { xcmCOInternetIPv6Address 7 } 
    -- integerTruthValue  

xcmCOInternetIPv6ManualAddressPrefixLength 
    OBJECT IDENTIFIER ::= { xcmCOInternetIPv6Address 8 } 
    -- integerNumber (1..128) 
    -- (see 'xcmCOInternetIPv6Address' for references) 
    -- Indicates the length of the prefix of manually configured IPv6  
    -- address e.g., by user configuration. 

xcmCOInternetIPv6EUI64InterfaceId 
    OBJECT IDENTIFIER ::= { xcmCOInternetIPv6 2 } 
    -- stringLocalization (IPv6 - hex w/ colons '[x1:...:x8]') 
    -- The EUI-64 Interface Identifier generated  
    -- automatically by the device from the Ethernet 
    -- MAC (physical/link layer) address. 

xcmCOInternetIPv6RouterAdvertisementAddressPrefix 
    OBJECT IDENTIFIER ::= { xcmCOInternetIPv6 3 } 
    -- stringLocalization 
    -- (IPv6 - eight hex values [0-4 octets] of 16-bit components 
    --  optionally followed by '/' and prefix length [1-3 octets] - 
    --  ASCII decimal of 1-octet prefix length) 
    -- (eg, 'FEDC:BA98:7654:3210:FEDC:BA98:7654:3210/64') 
    -- The IPv6 address prefix values received from 
    -- Router Advertisements when a router is present on the local 
    -- network per RFC 2462. 

xcmCOInternetIPv6DefaultGateway         -- IPv6 Default Gateway 

XCMI Working Group                File 52conftc                [Page 40]

Xerox Common Management Interface (XCMI) Standard               04/14/23

    OBJECT IDENTIFIER ::= { xcmCOInternetIPv6 4 } 
    -- stringLocalization (IPv6 - hex w/ colons '[x1:...:x8/yyy]') 
    -- (see 'xcmCOInternetIPv6Address' for references) 

xcmCOInternetIPv6HostName               -- System Hostname 
    OBJECT IDENTIFIER ::= { xcmCOInternetIPv6 5 } 
    -- stringLocalization 
    -- The HostName used for IPv4 and IPv6 will be one and the same. 

xcmCOInternetIPv6DUID               -- DUID IPv6 Unique Identifier 
    OBJECT IDENTIFIER ::= { xcmCOInternetIPv6 6 } 
    -- stringLocalization 
    -- Unique identifier generated by MFP 

xcmCOInternetIPSubnetMask       -- IP Subnet Mask 
    OBJECT IDENTIFIER ::= { xcmCOInternetIP 2 } 
    -- stringLocalization (IPv4 - dotted decimal 'a.b.c.d') 
    -- (see 'xcmCOInternetIPAddress' for references) 


xcmCOInternetIPAddressViaRARP   -- IP Address Via RARP (dynamic) 
    OBJECT IDENTIFIER ::= { xcmCOInternetIP 3 } 
    -- integerTruthValue (true=enableRARP, false=disableRARP) 
    -- (if false, then use 'xcmCOInternetIPAddress' value) 
    -- (obsoleted by 'xcmCOInternetIPAddressSource') 


xcmCOInternetIPDefaultGateway   -- IP Default Gateway 
    OBJECT IDENTIFIER ::= { xcmCOInternetIP 4 } 
    -- stringLocalization (IPv4 - dotted decimal 'a.b.c.d') 
    -- (see 'xcmCOInternetIPAddress' for references) 


xcmCOInternetIPAddressSource    -- IP Address Source (static/dynamic) 
    OBJECT IDENTIFIER ::= { xcmCOInternetIP 5 } 
    -- integerEnum (1=none, 2=other, 
    -- 3=static, 4=viaRARP, 5=viaBOOTP, 6=viaDHCP, 
    -- 7=viaDHCPAutoIP,  
    -- 8=viaAutoIPv6, 
    --  (see 'IPv6 Sateless Address Autoconfig', RFC 2462, Dec 1998) 
    -- 9=viaAutoIPv4) 
    --  (see 'draft-ietf-zeroconf-ipv4-linklocal-17.txt', Jul 2004 
    --  and Automatic Private IP Addressing) 
    --  (Obsoletes 'xcmCOInternetIPAddressViaRARP') 
xcmCOInternetIPDatalinks        -- IP Datalinks 
    OBJECT IDENTIFIER ::= { xcmCOInternetIP 12 } 
    -- integerTruthValue (w/ chain of 'xcmCOOsilan...') 
    -- (obsoleted by 'xcmCOInternetDatalinks') 
xcmCOInternetIPHostName         -- IP Host Name 
    OBJECT IDENTIFIER ::= { xcmCOInternetIP 50 } 
    -- stringLocalization 
xcmCOInternetIPAutoIPAddress -- Computed AutoIP Address 
OBJECT IDENTIFIER ::= { xcmCOInternetIP 51 } 
-- stringLocalization (IPv4 - dotted decimal '1.b.c.d') 

XCMI Working Group                File 52conftc                [Page 41]

Xerox Common Management Interface (XCMI) Standard               04/14/23

-- <or> 
-- stringLocalization (IPv6 - hex w/ colons '[x1:...:x8]') 
-- (IPv4 - decimal values [1-3 octets] or four 8-bit components) 
-- (eg, '13.226.19.10') 
-- (IPv6 - eight hex values [0-4 octets] of 16-bit components) 
-- (eg, 'FEDC:BA98:7654:3210:FEDC:BA98:7654:3210') 
-- (see section 2.2 'Textual Representation of Addresses' in 
-- RFC 2373, IPv6 Addressing Architecture) 
-- (see section 2 'Literal IPv6 Address Format in URL Syntax' in 
-- RFC 2732, Format for Literal IPv6 Addresses in URLs) 
xcmCOInternetIPAutoEnable          -- Enable auto IP Address 
    OBJECT IDENTIFIER ::= { xcmCOInternetIP 60 } 
    -- integerTruthValue (true=enabled, false=disabled) 

xcmCOInternetIPBcastCache 
   OBJECT IDENTIFIER ::= { xcmCOInternetIP 61 } 
   -- The upper level enumeration for the network address 
   -- caching for the walkup installation protocol 
xcmCOInternetIPInstall 
   OBJECT IDENTIFIER ::= { xcmCOInternetIP 62 } 
   -- The upper level enumeration for the walkup 
   -- installation protocol for device selection 

xcmCOInternetIPSec    
    OBJECT IDENTIFIER ::= { xcmCOInternetIP 70 } 
    -- integerTruthValue (true=enableIPSec, false=disableIPSec) 

-- Network Address Caching (xcmCOInternetIPBcastCache) 
xcmCOInternetIPBCacheEnabled     -- Network Address Cache Allowed 
    OBJECT IDENTIFIER ::= { xcmCOInternetIPBcastCache 1 } 
    -- integerTruthValue 
    -- (true=enable network addess caching, 
    --  false=disable caching) 

xcmCOInternetIPBCacheAddress1    -- Network Address Cache 1 
    OBJECT IDENTIFIER ::= { xcmCOInternetIPBcastCache 2 } 
    -- stringLocalization 
    -- The formatting for this string is the 
    -- per xcmCOInternetIPAutoIPAddress 
xcmCOInternetIPBCacheAddress2    -- Network Address Cache 2 
    OBJECT IDENTIFIER ::= { xcmCOInternetIPBcastCache 3 } 
    -- stringLocalization 
    -- The formatting for this string is the 
    -- per xcmCOInternetIPAutoIPAddress 
xcmCOInternetIPBCacheAddress3    -- Network Address Cache 3 
    OBJECT IDENTIFIER ::= { xcmCOInternetIPBcastCache 4 } 
    -- stringLocalization 
    -- The formatting for this string is the 
    -- per xcmCOInternetIPAutoIPAddress 
xcmCOInternetIPBCacheAddress4    -- Network Address Cache 4 
    OBJECT IDENTIFIER ::= { xcmCOInternetIPBcastCache 5 } 
    -- stringLocalization 
    -- The formatting for this string is the 
    -- per xcmCOInternetIPAutoIPAddress 

XCMI Working Group                File 52conftc                [Page 42]

Xerox Common Management Interface (XCMI) Standard               04/14/23


-- Installation Protocol for device selection (xcmCOInternetIPInstall) 
xcmCOInternetIPInstallSelect       -- Printer selected for installation 
   OBJECT IDENTIFIER ::= { xcmCOInternetIPInstall 1 } 
   -- integerTruthValue 
   -- (true=selected for installation, false=not selected) 
xcmCOInternetIPAllSubnetsLocal     -- Local-only Installation Subnets 
   OBJECT IDENTIFIER ::= { xcmCOInternetIPInstall 2 } 
   -- integerTruthValue 
   -- (true=Only local subnet allowed, 
   --  false=Remote subnets allowed) 

-- 
--  DHCP Configuration 
-- 
xcmCOInternetDHCPClassID        -- DHCP Class ID (option to server) 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCP 1 } 
    -- stringLocalization (dotted decimal 'ProductID' OR label of Pid) 
xcmCOInternetDHCPLeaseTime      -- DHCP Lease Time (option to server) 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCP 2 } 
    -- integerNumber (seconds, -1=infinite, 0=none, or 1..n) 
xcmCOInternetDHCPRequestTimeout -- DHCP Request Timeout (for replies) 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCP 3 } 
    -- integerNumber (seconds, 0=none, or 1..n) 

xcmCOInternetDHCPServer -- DHCP Server 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCP 4 } 
    -- stringLocalization 
    -- The server that provided the IP Address for this 
    -- device. The formatting for this string is the 
    -- per xcmCOInternetIPAutoIPAddress 

-- 
--  DHCP Options 
-- 
--  Final arc of each of the following DHCP option get/set flags is the 
--  option code as defined in IETF DHCP Options (RFC 2132, March 1997) 
-- 
--  DHCP options named 'xxxGet' are legal for read by client 
--  DHCP options named 'xxxSet' are legal for write/read by client 
-- 
xcmCOInternetDHCPOptionGet      -- DHCP Option Get (read by client) 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCP 10 } 
    -- integerTruthValue 
xcmCOInternetDHCPOptionSet      -- DHCP Option Set (write by client) 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCP 11 } 
    -- integerTruthValue 
-- 
--  DHCP Options - BOOTP Vendor Extensions in RFC 1497 (RFC 2132, pg 5) 
-- 
xcmCODHCPGetSubnetMask          -- single subnet mask 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 1 } 
    -- integerTruthValue 
xcmCODHCPGetSubnetTimeOffset    -- single subnet time offset 

XCMI Working Group                File 52conftc                [Page 43]

Xerox Common Management Interface (XCMI) Standard               04/14/23

    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 2 } 
    -- integerTruthValue 
xcmCODHCPGetRouter              -- list routers 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 3 } 
    -- integerTruthValue 
xcmCODHCPGetTPTimeServer        -- list RFC 868 time servers 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 4 } 
    -- integerTruthValue 
xcmCODHCPGetIEN116NameServer    -- list IEN 116 name servers 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 5 } 
    -- integerTruthValue 
xcmCODHCPGetDNSNameServer       -- list DNS name servers 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 6 } 
    -- integerTruthValue 
xcmCODHCPGetLogServer           -- list MIT-LCS UDP log servers 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 7 } 
    -- integerTruthValue 
xcmCODHCPGetCookieServer        -- list RFC 865 cookie servers 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 8 } 
    -- integerTruthValue 
xcmCODHCPGetLPRServer           -- list LPR servers 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 9 } 
    -- integerTruthValue 
xcmCODHCPGetImpressServer       -- list Imagen Impress servers 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 10 } 
    -- integerTruthValue 
xcmCODHCPGetResourceLocServer   -- list RFC 887 RLP servers 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 11 } 
    -- integerTruthValue 
xcmCODHCPGetHostName            -- single client host name 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 12 } 
    -- integerTruthValue 
xcmCODHCPGetHostNameSettingsOverride 
    OBJECT IDENTIFIER ::= { xcmCODHCPGetHostName 1 } 
    -- integerTruthValue 
xcmCODHCPGetBootFileSize        -- size in 512-octet blocks 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 13 } 
    -- integerTruthValue 
xcmCODHCPGetMeritDumpFile       -- single core dump file path 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 14 } 
    -- integerTruthValue 
xcmCODHCPGetDNSDomainName       -- single DNS domain name 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 15 } 
    -- integerTruthValue 
xcmCODHCPGetDNSDomainNameSettingsOverride 
    OBJECT IDENTIFIER ::= { xcmCODHCPGetDNSDomainName 1 } 
    -- integerTruthValue 
xcmCODHCPGetSwapServer          -- single client swap server 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 16 } 
    -- integerTruthValue 
xcmCODHCPGetRootPath            -- single client root path 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 17 } 
    -- integerTruthValue 
xcmCODHCPGetExtensionsPath      -- single client extensions path 

XCMI Working Group                File 52conftc                [Page 44]

Xerox Common Management Interface (XCMI) Standard               04/14/23

    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 18 } 
    -- integerTruthValue 
-- 
--  DHCP Options - IP Layer Parameters per Host (RFC 2132, pg 11) 
-- 
xcmCODHCPGetIPForwarding        -- single IP forwarding enable 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 19 } 
    -- integerTruthValue 
xcmCODHCPGetNLSourceRouting     -- non-local source route enable 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 20 } 
    -- integerTruthValue 
xcmCODHCPGetNLPolicyFilter      -- list nl source route filters 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 21 } 
    -- integerTruthValue 
xcmCODHCPGetMaxIPDatagramSize   -- single max IP datagram size 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 22 } 
    -- integerTruthValue 
xcmCODHCPGetIPDefaultTTL        -- single IP default TTL 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 23 } 
    -- integerTruthValue 
xcmCODHCPGetPathMTUAgeTimeout   -- single Path MTU age timeout 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 24 } 
    -- integerTruthValue 
xcmCODHCPGetPathMTUPlateau      -- list Path MTU sizes 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 25 } 
    -- integerTruthValue 
-- 
--  DHCP Options - IP Layer Parameters per Interface (RFC 2132, pg 13 
-- 
xcmCODHCPGetInterfaceMTUSize    -- single interface MTU size 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 26 } 
    -- integerTruthValue 
xcmCODHCPGetAllSubnetsLocal     -- single subnets local enable 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 27 } 
    -- integerTruthValue 
xcmCODHCPGetBroadcastAddress    -- single IP broadcast address 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 28 } 
    -- integerTruthValue 
xcmCODHCPGetMaskDiscovery       -- single mask discovery enable 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 29 } 
    -- integerTruthValue 
xcmCODHCPGetMaskSupplier        -- single mask response enable 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 30 } 
    -- integerTruthValue 
xcmCODHCPGetRouterDiscovery     -- single router discover enable 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 31 } 
    -- integerTruthValue 
xcmCODHCPGetRouterSolAddress    -- single router solicit address 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 32 } 
    -- integerTruthValue 
xcmCODHCPGetStaticRoute         -- list static routes 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 33 } 
    -- integerTruthValue 
-- 

XCMI Working Group                File 52conftc                [Page 45]

Xerox Common Management Interface (XCMI) Standard               04/14/23

--  DHCP Options - Link Layer Parameters per Interface (RFC 2132, pg 16)
-- 
xcmCODHCPGetARPTrailer          -- single ARP trailer enable 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 34 } 
    -- integerTruthValue 
xcmCODHCPGetARPCacheTimeout     -- single ARP cache timeout 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 35 } 
    -- integerTruthValue 
xcmCODHCPGetEthernetFrameIEEE   -- single IEEE 802.3 enable 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 36 } 
    -- integerTruthValue 
-- 
--  DHCP Options - TCP Layer Parameters per Interface (RFC 2132, pg 17) 
-- 
xcmCODHCPGetTCPDefaultTTL       -- single TCP default TTL 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 37 } 
    -- integerTruthValue 
xcmCODHCPGetTCPKeepInterval     -- single TCP keepalive interval 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 38 } 
    -- integerTruthValue 
xcmCODHCPGetTCPKeepGarbage      -- single TCP KA garbage enable 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 39 } 
    -- integerTruthValue 
-- 
--  DHCP Options - Application and Service Parameters (RFC 2132, pg 18) 
-- 
xcmCODHCPGetNISDomainName       -- single NIS domain name 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 40 } 
    -- integerTruthValue 
xcmCODHCPGetNISNameServer       -- list NIS name servers 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 41 } 
    -- integerTruthValue 
xcmCODHCPGetNTPTimeServer       -- list NTP time servers 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 42 } 
    -- integerTruthValue 
xcmCODHCPGetVendorSpecific      -- any vendor specific info 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 43 } 
    -- integerTruthValue 
xcmCODHCPGetNetbiosNameServer   -- list NetBIOS name servers 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 44 } 
    -- integerTruthValue 
xcmCODHCPGetNetbiosDistServer   -- list NetBIOS dg dist servers 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 45 } 
    -- integerTruthValue 
xcmCODHCPGetNetbiosNodeType     -- single NetBIOS node type 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 46 } 
    -- integerTruthValue 
xcmCODHCPGetNetbiosScope        -- single NetBIOS scope 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 47 } 
    -- integerTruthValue 
xcmCODHCPGetXWindowFontServer   -- list X Window font servers 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 48 } 
    -- integerTruthValue 
xcmCODHCPGetXWindowDisplayMgr   -- list X Window display mgrs 

XCMI Working Group                File 52conftc                [Page 46]

Xerox Common Management Interface (XCMI) Standard               04/14/23

    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 49 } 
    -- integerTruthValue 
xcmCODHCPGetNISPlusDomainName   -- single NIS+ domain name 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 64 } 
    -- integerTruthValue 
xcmCODHCPGetNISPlusNameServer   -- list NIS+ name servers 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 65 } 
    -- integerTruthValue 
xcmCODHCPGetMobileIPHomeAgent   -- list Mobile IP home agents 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 68 } 
    -- integerTruthValue 
xcmCODHCPGetSMTPMailServer      -- list SMTP mail servers 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 69 } 
    -- integerTruthValue 
xcmCODHCPGetPOP3MailServer      -- list POP3 mail servers 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 70 } 
    -- integerTruthValue 
xcmCODHCPGetNNTPNewsServer      -- list NNTP news servers 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 71 } 
    -- integerTruthValue 
xcmCODHCPGetWWWServer           -- list WWW servers 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 72 } 
    -- integerTruthValue 
xcmCODHCPGetFingerServer        -- list Finger servers 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 73 } 
    -- integerTruthValue 
xcmCODHCPGetIRCServer           -- list IRC chat servers 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 74 } 
    -- integerTruthValue 
xcmCODHCPGetStreetTalkServer    -- list StreetTalk name servers 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 75 } 
    -- integerTruthValue 
xcmCODHCPGetStreetTalkDAServer  -- list StreetTalk DA servers 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 76 } 
    -- integerTruthValue 
-- 
--  DHCP Options - DHCP Extensions (RFC 2132, pg 25) 
-- 
xcmCODHCPSetIPAddressRequest    -- single client IP address 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionSet 50 } 
    -- integerTruthValue 
xcmCODHCPSetIPAddressLeaseTime  -- single IP address lease time 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionSet 51 } 
    -- integerTruthValue 
xcmCODHCPSetOptionOverload      -- single option overload type 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionSet 52 } 
    -- integerTruthValue 
xcmCODHCPGetMessageType         -- single DHCP message type 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 53 } 
    -- integerTruthValue 
xcmCODHCPGetServerID            -- single DHCP server identifier 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 54 } 
    -- integerTruthValue 
xcmCODHCPGetParameterRequest    -- list DHCP parameter requests 

XCMI Working Group                File 52conftc                [Page 47]

Xerox Common Management Interface (XCMI) Standard               04/14/23

    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 55 } 
    -- integerTruthValue 
xcmCODHCPGetErrorMessage        -- single DHCP error message 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 56 } 
    -- integerTruthValue 
xcmCODHCPGetMaxMessageSize      -- single max DHCP message size 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 57 } 
    -- integerTruthValue 
xcmCODHCPGetRenewT1Interval     -- single renewing T1 interval 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 58 } 
    -- integerTruthValue 
xcmCODHCPGetRebindT2Interval    -- single rebind T2 interval 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 59 } 
    -- integerTruthValue 
xcmCODHCPSetClassID             -- single class identifier 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionSet 60 } 
    -- integerTruthValue 
xcmCODHCPSetClientID            -- single client identifier 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionSet 61 } 
    -- integerTruthValue 
xcmCODHCPGetTFTPServerName      -- single TFTP server name 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 66 } 
    -- stringLocalization (the name used by the device) 
xcmCODHCPGetBootFileName        -- single boot filename 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 67 } 
    -- stringLocalization (the name used by the device) 
-- 
--  DHCP Options - Novell NetWare Directory Services (RFC 2241, pg 18) 
-- 
xcmCODHCPGetNDSNameServer       -- list NetWare NDS name servers 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 85 } 
    -- integerTruthValue 
xcmCODHCPGetNDSTreeName         -- single NetWare NDS tree name 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 86 } 
    -- integerTruthValue 
xcmCODHCPGetNDSContext          -- single NetWare NDS context 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPOptionGet 87 } 
    -- integerTruthValue 

xcmCOInternetUDPAddress         -- UDP Address 
    OBJECT IDENTIFIER ::= { xcmCOInternetUDP 1 } 
    -- stringLocalization (IPv4 - dotted decimal 'a.b.c.d:socket') 
    -- (note - in IPv4 ONLY, a dot '.' MAY also be used before 'socket' 
    -- and such use of dot was recommended in XCMI v4.0 and earlier) 
    -- (see 'xcmCOInternetIPAddress' for references) 

xcmCOInternetUDPPort            -- UDP Port 
    OBJECT IDENTIFIER ::= { xcmCOInternetUDP 2 } 
    -- stringLocalization (ASCII decimal format, 'socket') 

xcmCOInternetTCPAddress         -- TCP Address 
    OBJECT IDENTIFIER ::= { xcmCOInternetTCP 1 } 
    -- stringLocalization (IPv4 - dotted decimal 'a.b.c.d:socket') 
    -- (note - in IPv4 ONLY, a dot '.' MAY also be used before 'socket' 

XCMI Working Group                File 52conftc                [Page 48]

Xerox Common Management Interface (XCMI) Standard               04/14/23

    -- and such use of dot was recommended in XCMI v4.0 and earlier) 
    -- (see 'xcmCOInternetIPAddress' for references) 


xcmCOInternetTCPPort            -- TCP Port 
    OBJECT IDENTIFIER ::= { xcmCOInternetTCP 2 } 
    -- stringLocalization (ASCII decimal format, 'socket') 

xcmCOInternetTCPMaxSegmentSize -- TCP Default Max Segment Size 
    OBJECT IDENTIFIER ::= { xcmCOInternetTCP 3 } 
    -- integerNumber   

xcmCOInternetApplications 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1700 } 
    -- integerTruthValue 

xcmCOInternetRaw                -- Raw Print (printing) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1501 } 
    -- integerTruthValue 
xcmCOInternetIPP                -- IPP (printing) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1502 } 
    -- integerTruthValue 
xcmCOInternetLPR                -- LPR (printing) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1503 } 
    -- integerTruthValue 

xcmCOInternetFTP                -- FTP (filing) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1504 } 
    -- integerTruthValue 
xcmCOInternetFTPPassiveMode -- FTP passive mode 
    OBJECT IDENTIFIER ::= { xcmCOInternetFTP 1 } 
    -- integerTruthValue 

xcmCOInternetSMTP               -- SMTP (email) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1505 } 
    -- integerTruthValue 
    -- (see RFC 821 / STD 10, 'Simple Mail Transfer Protocol', Aug 1982)
    -- (see RFC 1869 / STD 10, 'SMTP Service Extensions', November 1995)
xcmCOInternetTelnet             -- Telnet (virtual terminal) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1506 } 
    -- integerTruthValue 
xcmCOInternetDNS                -- DNS (directory) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1507 } 
    -- integerTruthValue 
xcmCOInternetTFTP               -- TFTP (filing) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1508 } 
    -- integerTruthValue 
xcmCOInternetHTTP               -- HTTP (World Wide Web - WWW) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1509 } 
    -- integerTruthValue 

xcmCOInternetSNMP               -- SNMP (network mgmt) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1510 } 
    -- integerTruthValue 

XCMI Working Group                File 52conftc                [Page 49]

Xerox Common Management Interface (XCMI) Standard               04/14/23

xcmCOInternetSNMPv1             -- SNMPv1 (network mgmt) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1511 } 
    -- integerTruthValue 
    -- (obsoleted by 'xcmCOInternetSNMPVersion') 
xcmCOInternetSNMPv2             -- SNMPv2 (network mgmt) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1512 } 
    -- integerTruthValue 
    -- (obsoleted by 'xcmCOInternetSNMPVersion') 
xcmCOInternetSNMPv3             -- SNMPv3 (network mgmt) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1513 } 
    -- integerTruthValue 
    -- (obsoleted by 'xcmCOInternetSNMPVersion') 
xcmCOInternetSNMPVersion        -- SNMP Version (network mgmt) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSNMP 1 } 
    -- integerEnum (from 'XcmGenSNMPVersion' in XCMI General TC) 
    -- (obsoletes 'xcmCOInternetSNMP[v1|v2|v3]') 

xcmCOInternetSNMPAdminAddress   -- SNMP Admin Address 
    OBJECT IDENTIFIER ::= { xcmCOInternetSNMP 2 } 
    -- integerTruthValue(8) & stringLocalization(13) 
    -- The SNMP Administrator Accept Address 
    -- i.e. the Host Access List for SNMP 

xcmCOInternetSNMPv1v2cWriteEnabled  -- SNMPv1v2c set enable commands 
    OBJECT IDENTIFIER ::= { xcmCOInternetSNMP 20 } 
    -- integerTruthValue  
    -- No SNMP v1 and v2c sets would be allowed. 
    -- Once disabled, SNMP sets can only be enabled via the WebUI 
    -- or through another version of SNMP that has its 'set enabled'. 

xcmCOInternetSNMPv3WriteEnabled  -- SNMPv3 set enable command 
    OBJECT IDENTIFIER ::= { xcmCOInternetSNMP 30 } 
    -- integerTruthValue  
    -- No SNMP v3 sets would be allowed. 
    -- Once disabled, SNMP sets can only be enabled via the WebUI 
    -- or through another version of SNMP that has its 'set enabled'. 

xcmCOInternetPOP3               -- Internet POP3 (email access) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1514 } 
    -- integerTruthValue 
    -- (see RFC 1939 / STD 53, 'Post Office Protocol v3', May 1996) 
    -- (see RFC 1957, 'Implementations of POP3', June 1996) 
    -- (see RFC 2384, 'POP URL Scheme', August 1998) 
    -- (see RFC 2449, 'POP3 Extension Mechanism, November 1998) 

xcmCOInternetIMAP4              -- Internet IMAP4 (email access) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1515 } 
    -- integerTruthValue 
    -- (see RFC 2060, 'Internet Msg Access Protocol v4', December 1996) 
    -- (see RFC 2192, 'IMAP URL Scheme', September 1997) 
    -- (see RFC 2683, 'IMAP4 Implementations', September 1999) 

xcmCOInternetFax                -- Internet Fax (facsimile over email) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1516 } 

XCMI Working Group                File 52conftc                [Page 50]

Xerox Common Management Interface (XCMI) Standard               04/14/23

    -- integerTruthValue 
    -- (see RFC 2305, 'Simple Fax Using Internet Mail', March 1998) 
    -- (see RFC 2532, 'Extended Fax Using Internet Mail', March 1999) 

xcmCOInternetNTP                -- NTP (RFC 4330) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1517} 
     -- integerTruthValue 

xcmCOInternetSFTP                -- SFTP (filing) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1518} 
 -- integerTruthValue 

xcmCOInternetWINS               -- Microsoft WINS (directory) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1519 } 
    -- integerTruthValue 

xcmCOInternetSunOncSuite        -- Sun ONC Suite (distributed computing)
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1520 } 
    -- integerTruthValue 
xcmCOInternetSunOncNIS          -- Sun ONC NIS (directory) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1521 } 
    -- integerTruthValue 
xcmCOInternetSunOncPlusNIS      -- Sun ONC+ NIS+ (directory) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1522 } 
    -- integerTruthValue 
xcmCOInternetSunOncRPC          -- Sun ONC RPC (w/ NIS) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1523 } 
    -- integerTruthValue 
xcmCOInternetSunOncPlusRPC      -- Sun ONC+ RPC (w/ NIS+) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1524 } 
    -- integerTruthValue 
xcmCOInternetSunTiRPC           -- Sun TI RPC (transactions) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1525 } 
    -- integerTruthValue 

xcmCOInternetHTTPS               -- HTTPS (World Wide Web - WWW) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1526 } 
    -- integerTruthValue 

xcmCOInternetOsfDceSuite        -- OSF DCE Suite (distributed computing)
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1530 } 
    -- integerTruthValue 
xcmCOInternetOsfDceCDS          -- OSF DCE CDS (directory) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1531 } 
    -- integerTruthValue 
xcmCOInternetOsfDceRPC          -- OSF DCE RPC (w/ CDS) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1532 } 
    -- integerTruthValue 
xcmCOInternetOsfDceKerberos     -- OSF DCE Kerberos (security tickets) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1533 } 
    -- integerTruthValue 

xcmCOInternetOsfDmeSuite        -- OSF DME Suite (distributed mgmt) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1540 } 

XCMI Working Group                File 52conftc                [Page 51]

Xerox Common Management Interface (XCMI) Standard               04/14/23

    -- integerTruthValue 

xcmCOInternetSecurityDeviceCertificate  
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1545 } 
    -- stringLocalization (255 character string) 

xcmCOInternetServerDeviceCertificate  
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1546 } 
    -- stringLocalization (255 character string) 

 xcmCOInternetLDAP               -- LDAP (to X.500 directory, RFC 1777) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1551 } 
    -- integerTruthValue 
xcmCOInternetCLDAP              -- CLDAP (to X.500 directory, RFC 1798) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1552 } 
    -- integerTruthValue 

xcmCOInternetSalutation         -- Salutation (FX/IBM consortium) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1561 } 
    -- integerTruthValue 

xcmCOInternetUpnpSuite          -- MS UPnP Suite (plug-and-play) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1570 } 
    -- integerTruthValue 
xcmCOInternetUpnpSSDP           -- MS UPnP SSDP (discovery) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1571 } 
    -- integerTruthValue 
xcmCOInternetUpnpGENA           -- MS UPnP GENA (notification) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1572 } 
    -- integerTruthValue 
xcmCOInternetThinPrintEnable       -- ThinPrint Enable 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1573 } 
    -- integerTruthValue 
xcmCOInternetThinPrintPort         -- ThinPrint Port 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1574 } 
    -- integerNumber 
xcmCOInternetThinPrintPacketSize   -- ThinPrint Packet 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1575 } 
    -- integerNumber 
xcmCOInternetThinPrintPacketSizeAuto -- ThinPrint Server-Choose Packet 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1576 } 
    -- integerTruthValue 
xcmCOInternetThinPrintPrinterClass   -- ThinPrint Printer Class 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1577 } 
    -- stringLocalization 
xcmCOInternetThinPrintTLSEnable      -- ThinPrint TLS Enable 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1578 } 
    -- integerTruthValue 

xcmCOInternetSLP                -- SLP (discovery) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1591 } 
    -- integerTruthValue 
xcmCOInternetSLPv1              -- SLPv1 (discovery) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1592 } 

XCMI Working Group                File 52conftc                [Page 52]

Xerox Common Management Interface (XCMI) Standard               04/14/23

    -- integerTruthValue 
    -- (obsoleted by 'xcmCOInternetSLPVersion') 
xcmCOInternetSLPv2              -- SLPv2 (discovery) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1593 } 
    -- integerTruthValue 
    -- (obsoleted by 'xcmCOInternetSLPVersion') 

-- 
--          Web Services on Devices Protocol Suite 
-- 

xcmCOInternetWSDSuite           -- Web Services on Devices 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1595 } 
        -- integerTruthValue 

xcmCOInternetWSDiscovery        -- WS-Discovery Protocol 
    OBJECT IDENTIFIER ::= { xcmCOInternetWSDSuite 1 } 
    -- integerTruthValue 

xcmCOInternetWSXResourcePort    -- Xerox WS-XResource Port Number 
    OBJECT IDENTIFIER ::= { xcmCOInternetWSDSuite 2 } 
    -- integerNumber 
    -- Xerox Resource Service Listening Port Number 

xcmCOInternetWSDiscoveryMulticast  -- WS-Discovery Multicast 
    OBJECT IDENTIFIER ::= { xcmCOInternetWSDiscovery 1 } 
    -- integerTruthValue 

xcmCOInternetWSDiscoveryPort    -- WS-Discovery Port Number 
    OBJECT IDENTIFIER ::= { xcmCOInternetWSDiscovery 2 } 
        -- integerNumber 
    -- Web Services Discovery Listening Port Number 

xcmCOInternetWSPrintPort       -- Microsoft WS-Print Port Number 
    OBJECT IDENTIFIER ::= { xcmCOInternetWSDSuite 3 } 
    -- integerNumber 
    -- Print Service Listening Port Number 

xcmCOInternetWSScanPort        -- Microsoft WS-Scan Port Number 
    OBJECT IDENTIFIER ::= { xcmCOInternetWSDSuite 4 } 
    -- integerNumber 
    -- Scan Service Listening Port Number 

xcmCOInternetWSTransferPort       -- WS-Transfer Port 
    OBJECT IDENTIFIER ::= { xcmCOInternetWSDSuite 5 } 
    -- integerNumber 
    -- Web Services Transfer Listening Port Number 

xcmCOInternetWSFaxServerAPI       
    OBJECT IDENTIFIER ::= { xcmCOInternetWSDSuite 6 } 
    -- oidObject 

xcmCOInternetDeallocateAllDynamicResources    
-- Configuration mechanism.  Used to release all resources  

XCMI Working Group                File 52conftc                [Page 53]

Xerox Common Management Interface (XCMI) Standard               04/14/23

-- that have been dynamically allocated to the system. 
-- Helps prevent stale records. 
-- If enabled, on shutdown: 
--       if DHCP is enabled, send DHCPRELEASE to DHCP server 
--       if DDNS is enabled, delete resource records being  
--          maintained by the device 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite  1600} 
    -- integerTruthValue 
    -- (true=enable, false=disable) 

xcmCOInternetDHCPv6               -- DHCPv6 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1800 } 
-- integerTruthValue 
-- DHCPv6 
    -- RFC 3315, Dynamic Host Configuration Protocol for IPv6 (DHCPv6) 

xcmCOInternetDHCPv6ConfigState    -- DHCPv6 configuration 
    OBJECT IDENTIFIER ::= { xcmCOInternetDHCPv6 1 } 
-- integerEnum (1=Use DHCPv6 as directed by a router, 
-- 2=Always enable DHCP for address assignment, 
-- 3=Always enable DHCP for other configuration data, 
-- 4=Never use DHCPv6) 

xcmCOInternetDNSv6                -- DNS (directory) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1801 } 
-- integerTruthValue 
-- DNS over IPv6 

xcmCOInternetDNSv6DomainName      -- DNS Domain Name (directory) 
    OBJECT IDENTIFIER ::= { xcmCOInternetDNSv6 1 } 
-- stringLocalization 
-- The domain name for this system for DNS over IPv6. 

xcmCOInternetDNSv6ServerAddress   -- DNS Server Address (directory) 
OBJECT IDENTIFIER ::= { xcmCOInternetDNSv6 2 } 
-- stringLocalization (IPv6 - hex w/ colons '[x1:...:x8/yyy]') 
-- (see 'xcmCOInternetIPv6Address' for references) 

xcmCOInternetDNSv6DynamicUpdate   -- DNS Dynamic Update (directory) 
OBJECT IDENTIFIER ::= { xcmCOInternetDNSv6 3 } 
-- integerTruthValue 
-- (true=enableDynamicUpdate, false=disableDynamicUpdate) 
-- (see RFC 2136 'Dynamic Updates in DNS', April 1997) 

xcmCOInternetDNSv6ResolutionPolicy    -- Resolution Policy 
    OBJECT IDENTIFIER ::= { xcmCOInternetDNSv6 4 } 
-- Used to choose address when hostname DNS query  
-- returns both IPv4 and IPv6 addresses 
-- integerEnum (1=prefer IPv4 address, 
-- 2=prefer IPv6 address) 


xcmCOInternetIPv6DeallocateAllDynamicResources    
-- Configuration mechanism.  Used to release all resources  

XCMI Working Group                File 52conftc                [Page 54]

Xerox Common Management Interface (XCMI) Standard               04/14/23

    -- that have been dynamically allocated to the system. 
-- Helps prevent stale records. 
-- If enabled, on shutdown: 
--       if DHCPv6 is enabled, send DHCPRELEASE to DHCPv6 server 
--       if DDNSv6 is enabled, delete resource records being  
--          maintained by the device 
OBJECT IDENTIFIER ::= { xcmCOInternetSuite 1802} 
-- integerTruthValue 
-- (true=enable, false=disable) 

xcmCOInternetSLPVersion         -- SLP Version (discovery) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSLP 1 } 
    -- integerEnum (1=none, 2=other, 
    -- 3=SLPv1,                                     - RFC 2165 
    -- 4=SLPv2)                                     - RFC 2608 
    -- (obsoletes 'xcmCOInternetSLP[v1|v2]') 

xcmCOInternetRawHostName        -- Raw Host Name 
    OBJECT IDENTIFIER ::= { xcmCOInternetRaw 1 } 
    -- stringLocalization 


xcmCOInternetRawHostAddress     -- Raw Host Address 
    OBJECT IDENTIFIER ::= { xcmCOInternetRaw 2 } 
    -- stringLocalization (IPv4 - dotted decimal 'a.b.c.d') 
    -- (see 'xcmCOInternetIPAddress' for references) 

xcmCOInternetRawListenSocket    -- Raw Listen Socket 
    OBJECT IDENTIFIER ::= { xcmCOInternetRaw 3 } 
    -- integerNumber (9100=default or 1..n) 
    -- (see Internet Assigned Numbers, RFC 1700, and IANA registry) 
xcmCOInternetRawMaxClients      -- Raw Max Clients (concurrently) 
    OBJECT IDENTIFIER ::= { xcmCOInternetRaw 4 } 
    -- integerNumber (0..n) 
xcmCOInternetRawAcceptAddress   -- Raw Accept Address (list) 
    OBJECT IDENTIFIER ::= { xcmCOInternetRaw 11 } 
    -- integerTruthValue (w/ chain of 'xcmCOInternetIPAddress') 
xcmCOInternetRawAcceptSubnet    -- Raw Accept Subnet (list) 
    OBJECT IDENTIFIER ::= { xcmCOInternetRaw 12 } 
    -- integerTruthValue (w/ chain of 'xcmCOInternetIPSubnetMask') 
xcmCOInternetRawRejectAddress   -- Raw Reject Address (list) 
    OBJECT IDENTIFIER ::= { xcmCOInternetRaw 21 } 
    -- integerTruthValue (w/ chain of 'xcmCOInternetIPAddress') 
xcmCOInternetRawRejectSubnet    -- Raw Reject Subnet (list) 
    OBJECT IDENTIFIER ::= { xcmCOInternetRaw 22 } 
    -- integerTruthValue (w/ chain of 'xcmCOInternetIPSubnetMask') 
xcmCOInternetRawSpool           -- Raw Spool (printing) 
    OBJECT IDENTIFIER ::= { xcmCOInternetRaw 31 } 
    -- integerEnum (1=none, 2=other, 3=disk, 4=ram) 
xcmCOInternetRawMaxSpool        -- Raw Max Spool (printing) 
    OBJECT IDENTIFIER ::= { xcmCOInternetRaw 32 } 
    -- integerNumber (spool area size in bytes, 0..n) 
xcmCOInternetRawJobTimeout      -- Raw Job Timeout (printing) 
    OBJECT IDENTIFIER ::= { xcmCOInternetRaw 40 } 

XCMI Working Group                File 52conftc                [Page 55]

Xerox Common Management Interface (XCMI) Standard               04/14/23

    -- integerNumber (seconds, 0=infinite or 1..n) 
xcmCOInternetRawAutoSwitch      -- Raw Auto Switch (printing) 
    OBJECT IDENTIFIER ::= { xcmCOInternetRaw 41 } 
    -- integerEnum (see 'xcmCODirectPrintProtocol' below) 
xcmCOInternetRawBinaryPS        -- Raw Binary PS (printing) 
    OBJECT IDENTIFIER ::= { xcmCOInternetRaw 42 } 
    -- integerTruthValue (true=enableBinaryPS, false=disableBinaryPS) 
    -- (interpret all PostScript jobs as binary - ignore control chars) 
    -- (PostScript per job submission protocol or 'xxxDefaultPDL' below)
xcmCOInternetRawDefaultPDL      -- Raw Default PDL (printing) 
    OBJECT IDENTIFIER ::= { xcmCOInternetRaw 43 } 
    -- integerEnum ('XcmPrtInterpreterLangFamily' in XCMI Prt Ext TC) 
    -- (fixed PDL if 'xxxAutoSwitch' is 'none' or 'other') 
    -- (default PDL if 'xxxAutoSwitch' is 'autoSwitch') 
    -- (ignored if 'xxxAutoSwitch' is 'ps...' or 'hp...') 
    -- See: 'prtInterpreterLangFamily' in IETF Printer MIB (RFC 1759) 
    -- See: 'prtChannelDefaultPageDescLangIndex' (default PDL via value 
    --      of 'prtInterpreterIndex') in IETF Printer MIB (RFC 1759) 
xcmCOInternetRawBidirectional      --  
    OBJECT IDENTIFIER ::= { xcmCOInternetRaw 44 } 
    -- integerTruthValue (true=enabled, false=disabled) 


xcmCOInternetRawJobLimitPerConnection  
    OBJECT IDENTIFIER ::= { xcmCOInternetRaw 45 } 
    -- integerNumber (0..32768 where default=0 or unlimited,  
    --                device disconnects after limit reached) 

xcmCOInternetRawConcurrentJobsPerConnection  
    OBJECT IDENTIFIER ::= { xcmCOInternetRaw 46 } 
     -- integerNumber (0..500 where default=0) 

xcmCOInternetRawControlDEndOfPSJob  
    OBJECT IDENTIFIER ::= { xcmCOInternetRaw 47 } 
    -- integerTruthValue (1=true/enabled, 2-false/disabled,  
    --                    default=2 false/disabled) 

xcmCOInternetRawOutOfOrderBiDirectional 
    OBJECT IDENTIFIER ::= { xcmCOInternetRaw 48 } 
    -- integerTruthValue (1=true/enabled, 2-false/disabled,  
    --                    default=2 false/disabled) 

xcmCOInternetRawJobBannerPageEnabled  
    OBJECT IDENTIFIER ::= { xcmCOInternetRaw 49 } 
    -- integerNumber (1=NoJobs, 2=FirstJobOnly,3=AllJobs=Default) 

xcmCOInternetRawDocumentBannerPageEnabled 
    OBJECT IDENTIFIER ::= { xcmCOInternetRaw 50 } 
    -- integerTruthValue (1=true/enabled, 2-false/disabled,  
    --                    default=1 true/enabled) 

xcmCOInternetRawJobBannerPagePJLCmdsEnabled 
    OBJECT IDENTIFIER ::= { xcmCOInternetRaw 51 } 

XCMI Working Group                File 52conftc                [Page 56]

Xerox Common Management Interface (XCMI) Standard               04/14/23

    -- integerTruthValue (1=true/enabled, 2-false/disabled,  
    -- default=1 true/enabled) 

xcmCOInternetRawJobDataParsingOverride 
    OBJECT IDENTIFIER ::= { xcmCOInternetRaw 52 } 
    -- integerTruthValue (1=true/enabled, 2-false/disabled,  
    --                    default=2 false/disabled) 

xcmCOInternetRawSendPJLUSTATUSEarly 
    OBJECT IDENTIFIER ::= { xcmCOInternetRaw 53 } 
    -- integerTruthValue (1=true/enabled, 2-false/disabled,  
    --                    default=2 false/disabled) 

xcmCOInternetIPPHostName        -- IPP Host Name 
    OBJECT IDENTIFIER ::= { xcmCOInternetIPP 1 } 
    -- stringLocalization 

xcmCOInternetIPPHostAddress     -- IPP Host Address 
    OBJECT IDENTIFIER ::= { xcmCOInternetIPP 2 } 
    -- stringLocalization (IPv4 - dotted decimal 'a.b.c.d') 
    -- (see 'xcmCOInternetIPAddress' for references) 

xcmCOInternetIPPListenSocket    -- IPP Listen Socket 
    OBJECT IDENTIFIER ::= { xcmCOInternetIPP 3 } 
    -- integerNumber (631=default or 1..n) 
    -- (see Internet Assigned Numbers, RFC 1700, and IANA registry) 

xcmCOInternetIPPMaxClients      -- IPP Max Clients (concurrently) 
    OBJECT IDENTIFIER ::= { xcmCOInternetIPP 4 } 
    -- integerNumber (0..n) 


xcmCOInternetIPPIdentifyPrinterEnable 
    OBJECT IDENTIFIER ::= { xcmCOInternetIPP 5 } 
    -- integerTruthValue (1=true/enabled, 2-false/disabled,  
    --                    default=1 true/enabled) 

xcmCOInternetIPPFaxOutLogDisplayEnable 
    OBJECT IDENTIFIER ::= { xcmCOInternetIPP 6 } 
    -- integerTruthValue (1=true/enabled, 2-false/disabled,  
    --                    default=1 true/enabled) 

xcmCOInternetIPPVersionString   -- IPP Version String 
    OBJECT IDENTIFIER ::= { xcmCOInternetIPP 9 } 
    -- stringLocalization (eg, '1.1' for IPP/1.1, RFC 2910/2911) 
xcmCOInternetIPPAcceptAddress   -- IPP Accept Address (list) 
    OBJECT IDENTIFIER ::= { xcmCOInternetIPP 11 } 
    -- integerTruthValue (w/ chain of 'xcmCOInternetIPAddress') 
xcmCOInternetIPPAcceptSubnet    -- IPP Accept Subnet (list) 
    OBJECT IDENTIFIER ::= { xcmCOInternetIPP 12 } 
    -- integerTruthValue (w/ chain of 'xcmCOInternetIPSubnetMask') 
xcmCOInternetIPPRejectAddress   -- IPP Reject Address (list) 
    OBJECT IDENTIFIER ::= { xcmCOInternetIPP 21 } 
    -- integerTruthValue (w/ chain of 'xcmCOInternetIPAddress') 

XCMI Working Group                File 52conftc                [Page 57]

Xerox Common Management Interface (XCMI) Standard               04/14/23

xcmCOInternetIPPRejectSubnet    -- IPP Reject Subnet (list) 
    OBJECT IDENTIFIER ::= { xcmCOInternetIPP 22 } 
    -- integerTruthValue (w/ chain of 'xcmCOInternetIPSubnetMask') 
xcmCOInternetIPPSpool           -- IPP Spool (printing) 
    OBJECT IDENTIFIER ::= { xcmCOInternetIPP 31 } 
    -- integerEnum (1=none, 2=other, 3=disk, 4=ram) 
xcmCOInternetIPPMaxSpool        -- IPP Max Spool (printing) 
    OBJECT IDENTIFIER ::= { xcmCOInternetIPP 32 } 
    -- integerNumber (spool area size in bytes, 0..n) 
xcmCOInternetIPPJobTimeout      -- IPP Job Timeout (printing) 
    OBJECT IDENTIFIER ::= { xcmCOInternetIPP 40 } 
    -- integerNumber (seconds, 0=infinite or 1..n) 
xcmCOInternetIPPAutoSwitch      -- IPP Auto Switch (printing) 
    OBJECT IDENTIFIER ::= { xcmCOInternetIPP 41 } 
    -- integerEnum (see 'xcmCODirectPrintProtocol' below) 
xcmCOInternetIPPBinaryPS        -- IPP Binary PS (printing) 
    OBJECT IDENTIFIER ::= { xcmCOInternetIPP 42 } 
    -- integerTruthValue (true=enableBinaryPS, false=disableBinaryPS) 
    -- (interpret all PostScript jobs as binary - ignore control chars) 
    -- (PostScript per job submission protocol or 'xxxDefaultPDL' below)
xcmCOInternetIPPDefaultPDL      -- IPP Default PDL (printing) 
    OBJECT IDENTIFIER ::= { xcmCOInternetIPP 43 } 
    -- integerEnum ('XcmPrtInterpreterLangFamily' in XCMI Prt Ext TC) 
    -- (fixed PDL if 'xxxAutoSwitch' is 'none' or 'other') 
    -- (default PDL if 'xxxAutoSwitch' is 'autoSwitch') 
    -- (ignored if 'xxxAutoSwitch' is 'ps...' or 'hp...') 
    -- See: 'prtInterpreterLangFamily' in IETF Printer MIB (RFC 1759) 
    -- See: 'prtChannelDefaultPageDescLangIndex' (default PDL via value 
    --      of 'prtInterpreterIndex') in IETF Printer MIB (RFC 1759) 
xcmCOInternetIPPAuthScheme   -- IPP Authentication Scheme 
    OBJECT IDENTIFIER ::= { xcmCOInternetIPP 50 } 
    -- integerEnum (Basic(2), Digest(3)) 
    -- The IPP Authentication Scheme selected by the user 


xcmCOInternetLPRHostName        -- LPR Host Name 
    OBJECT IDENTIFIER ::= { xcmCOInternetLPR 1 } 
    -- stringLocalization 

xcmCOInternetLPRHostAddress     -- LPR Host Address 
    OBJECT IDENTIFIER ::= { xcmCOInternetLPR 2 } 
    -- stringLocalization (IPv4 - dotted decimal 'a.b.c.d') 
    -- (see 'xcmCOInternetIPAddress' for references) 

xcmCOInternetLPRListenSocket    -- LPR Listen Socket (RFC 1179) 
    OBJECT IDENTIFIER ::= { xcmCOInternetLPR 3 } 
    -- integerNumber (515=default or 1..n) 
    -- (see Internet Assigned Numbers, RFC 1700, and IANA registry) 
xcmCOInternetLPRMaxClients      -- LPR Max Clients (concurrently) 
    OBJECT IDENTIFIER ::= { xcmCOInternetLPR 4 } 
    -- integerNumber (0..n) 
xcmCOInternetLPRAcceptAddress   -- LPR Accept Address (list) 
    OBJECT IDENTIFIER ::= { xcmCOInternetLPR 11 } 
    -- integerTruthValue (w/ chain of 'xcmCOInternetIPAddress') 

XCMI Working Group                File 52conftc                [Page 58]

Xerox Common Management Interface (XCMI) Standard               04/14/23

xcmCOInternetLPRAcceptSubnet    -- LPR Accept Subnet (list) 
    OBJECT IDENTIFIER ::= { xcmCOInternetLPR 12 } 
    -- integerTruthValue (w/ chain of 'xcmCOInternetIPSubnetMask') 
xcmCOInternetLPRRejectAddress   -- LPR Reject Address (list) 
    OBJECT IDENTIFIER ::= { xcmCOInternetLPR 21 } 
    -- integerTruthValue (w/ chain of 'xcmCOInternetIPAddress') 
xcmCOInternetLPRRejectSubnet    -- LPR Reject Subnet (list) 
    OBJECT IDENTIFIER ::= { xcmCOInternetLPR 22 } 
    -- integerTruthValue (w/ chain of 'xcmCOInternetIPSubnetMask') 
xcmCOInternetLPRSpool           -- LPR Spool (printing) 
    OBJECT IDENTIFIER ::= { xcmCOInternetLPR 31 } 
    -- integerEnum (1=none, 2=other, 3=disk, 4=ram) 
xcmCOInternetLPRMaxSpool        -- LPR Max Spool (printing) 
    OBJECT IDENTIFIER ::= { xcmCOInternetLPR 32 } 
    -- integerNumber (spool area size in bytes, 0..n) 
xcmCOInternetLPRJobTimeout      -- LPR Job Timeout (printing) 
    OBJECT IDENTIFIER ::= { xcmCOInternetLPR 40 } 
    -- integerNumber (seconds, 0=infinite or 1..n) 
xcmCOInternetLPRAutoSwitch      -- LPR Auto Switch (printing) 
    OBJECT IDENTIFIER ::= { xcmCOInternetLPR 41 } 
    -- integerEnum (see 'xcmCODirectPrintProtocol' below) 
xcmCOInternetLPRBinaryPS        -- LPR Binary PS (printing) 
    OBJECT IDENTIFIER ::= { xcmCOInternetLPR 42 } 
    -- integerTruthValue (true=enableBinaryPS, false=disableBinaryPS) 
    -- (interpret all PostScript jobs as binary - ignore control chars) 
    -- (PostScript per job submission protocol or 'xxxDefaultPDL' below)
xcmCOInternetLPRDefaultPDL      -- LPR Default PDL (printing) 
    OBJECT IDENTIFIER ::= { xcmCOInternetLPR 43 } 
    -- integerEnum ('XcmPrtInterpreterLangFamily' in XCMI Prt Ext TC) 
    -- (fixed PDL if 'xxxAutoSwitch' is 'none' or 'other') 
    -- (default PDL if 'xxxAutoSwitch' is 'autoSwitch') 
    -- (ignored if 'xxxAutoSwitch' is 'ps...' or 'hp...') 
    -- See: 'prtInterpreterLangFamily' in IETF Printer MIB (RFC 1759) 
    -- See: 'prtChannelDefaultPageDescLangIndex' (default PDL via value 
    --      of 'prtInterpreterIndex') in IETF Printer MIB (RFC 1759) 

xcmCOInternetSMTPHostName       -- SMTP Host Name 
    OBJECT IDENTIFIER ::= { xcmCOInternetSMTP 1 } 
    -- stringLocalization 

xcmCOInternetSMTPHostAddress    -- SMTP Host Address 
    OBJECT IDENTIFIER ::= { xcmCOInternetSMTP 2 } 
    -- stringLocalization (IPv4 - dotted decimal 'a.b.c.d') 
    -- (see 'xcmCOInternetIPAddress' for references) 

xcmCOInternetSMTPListenSocket   -- SMTP Listen Socket 
    OBJECT IDENTIFIER ::= { xcmCOInternetSMTP 3 } 
    -- integerNumber (25=default or 1..n) 
    -- (see Internet Assigned Numbers, RFC 1700, and IANA registry) 
xcmCOInternetSMTPMaxClients     -- SMTP Max Clients (concurrently) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSMTP 4 } 
    -- integerNumber (0..n) 
xcmCOInternetSMTPAcceptAddress  -- SMTP Accept Address (list) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSMTP 11 } 

XCMI Working Group                File 52conftc                [Page 59]

Xerox Common Management Interface (XCMI) Standard               04/14/23

    -- integerTruthValue (w/ chain of 'xcmCOInternetIPAddress') 
xcmCOInternetSMTPAcceptSubnet   -- SMTP Accept Subnet (list) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSMTP 12 } 
    -- integerTruthValue (w/ chain of 'xcmCOInternetIPSubnetMask') 
xcmCOInternetSMTPRejectAddress  -- SMTP Reject Address (list) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSMTP 21 } 
    -- integerTruthValue (w/ chain of 'xcmCOInternetIPAddress') 
xcmCOInternetSMTPRejectSubnet   -- SMTP Reject Subnet (list) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSMTP 22 } 
    -- integerTruthValue (w/ chain of 'xcmCOInternetIPSubnetMask') 
xcmCOInternetSMTPSpool          -- SMTP Spool (printing) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSMTP 31 } 
    -- integerEnum (1=none, 2=other, 3=disk, 4=ram) 
xcmCOInternetSMTPMaxSpool       -- SMTP Max Spool (printing) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSMTP 32 } 
    -- integerNumber (spool area size in bytes, 0..n) 
xcmCOInternetSMTPJobTimeout     -- SMTP Job Timeout (printing) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSMTP 40 } 
    -- integerNumber (seconds, 0=infinite or 1..n) 
xcmCOInternetSMTPAutoSwitch     -- SMTP Auto Switch (printing) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSMTP 41 } 
    -- integerEnum (see 'xcmCODirectPrintProtocol' below) 
xcmCOInternetSMTPBinaryPS       -- SMTP Binary PS (printing) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSMTP 42 } 
    -- integerTruthValue (true=enableBinaryPS, false=disableBinaryPS) 
    -- (interpret all PostScript jobs as binary - ignore control chars) 
    -- (PostScript per job submission protocol or 'xxxDefaultPDL' below)
xcmCOInternetSMTPDefaultPDL     -- SMTP Default PDL (printing) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSMTP 43 } 
    -- integerEnum ('XcmPrtInterpreterLangFamily' in XCMI Prt Ext TC) 
    -- (fixed PDL if 'xxxAutoSwitch' is 'none' or 'other') 
    -- (default PDL if 'xxxAutoSwitch' is 'autoSwitch') 
    -- (ignored if 'xxxAutoSwitch' is 'ps...' or 'hp...') 
    -- See: 'prtInterpreterLangFamily' in IETF Printer MIB (RFC 1759) 
    -- See: 'prtChannelDefaultPageDescLangIndex' (default PDL via value 
    --      of 'prtInterpreterIndex') in IETF Printer MIB (RFC 1759) 
xcmCOInternetSMTPSubject        -- SMTP Subject (default) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSMTP 44 } 
    -- stringLocalization 
    -- (default subject field for outgoing SMTP message) 
xcmCOInternetSMTPSignatureLine  -- SMTP Signature Line (default) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSMTP 45 } 
    -- stringLocalization 
    -- (default signature line for outgoing SMTP message) 
xcmCOInternetSMTPUserName       -- SMTP User Name (for login to MTA) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSMTP 47 } 
    -- stringLocalization 
    -- (default user name for login to remote MTA) 
xcmCOInternetSMTPPassword       -- SMTP Password (for login to MTA) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSMTP 48 } 
    -- stringLocalization (SHALL be encrypted) 
    -- (default password for login to remote MTA) 
xcmCOInternetSMTPMaxInputText   -- SMTP Max Text Body Size (incoming) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSMTP 50 } 

XCMI Working Group                File 52conftc                [Page 60]

Xerox Common Management Interface (XCMI) Standard               04/14/23

    -- integerNumber (bytes, 0=none, or 1..n) 
    -- (max text body size for incoming SMTP message) 
    -- (value of zero indicates incoming text body is NOT allowed) 
xcmCOInternetSMTPMaxInputAttach -- SMTP Max Attachment Size (incoming) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSMTP 51 } 
    -- integerNumber (bytes, 0=none, or 1..n) 
    -- (max attachment size for incoming SMTP message) 
    -- (value of zero indicates incoming attachment is NOT allowed) 
xcmCOInternetSMTPMaxOutputText  -- SMTP Max Text Body Size (outgoing) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSMTP 52 } 
    -- integerNumber (bytes, 0=none, or 1..n) 
    -- (max text body size for outgoing SMTP message) 
    -- (value of zero indicates outgoing text body is NOT allowed) 
xcmCOInternetSMTPMaxOutputAttach -- SMTP Max Attachment Size (outgoing) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSMTP 53 } 
    -- integerNumber (bytes, 0=none, or 1..n) 
    -- (max attachment size for outgoing SMTP message) 
    -- (value of zero indicates outgoing attachment is NOT allowed) 
xcmCOInternetSMTPConfirmRequest -- SMTP Confirm Outgoing Email 
    OBJECT IDENTIFIER ::= { xcmCOInternetSMTP 54 } 
    -- integerTruthValue (true=enableDSN, false=disableDSN) 
xcmCOInternetSMTPConfirmReply   -- SMTP Confirm Incoming Email 
    OBJECT IDENTIFIER ::= { xcmCOInternetSMTP 55 } 
    -- integerTruthValue (true=enableDSN, false=disableDSN) 
xcmCOInternetSMTPConfirmTimeout -- SMTP Confirm Outgoing Timeout 
    OBJECT IDENTIFIER ::= { xcmCOInternetSMTP 56 } 
    -- integerNumber (seconds, 0=none, or 1..n) 
xcmCOInternetSMTPFeatureReply   -- SMTP Feature Report in Confirm Reply 
    OBJECT IDENTIFIER ::= { xcmCOInternetSMTP 57 } 
    -- integerTruthValue (true=enableReport, false=disableReport) 
xcmCOInternetSMTPMailAddress    -- SMTP Mail Address 
    OBJECT IDENTIFIER ::= { xcmCOInternetSMTP 58 } 
    -- stringLocalization (RFC 822 format - 'user@hostname') 
    -- (see RFC 822, 'Format of Internet Mail Messages', August, 1982) 
xcmCOInternetSMTPMaxInFragments -- SMTP Max Fragments (incoming) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSMTP 59 } 
    -- integerNumber (0=none, or 2..n) 
    -- (max fragments for incoming SMTP message) 
    -- (zero indicates incoming fragments are NOT allowed) 
xcmCOInternetSMTPMaxOutFragments -- SMTP Max Fragments (outgoing) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSMTP 60 } 
    -- integerNumber (0=none, or 2..n) 
    -- (max fragments for outgoing SMTP message) 
    -- (zero indicates outgoing fragments are NOT allowed) 
xcmCOInternetSMTPMaxInAttachments -- SMTP Max Attachments (incoming) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSMTP 61 } 
    -- integerNumber (0=none, or 1..n) 
    -- (max attachments for incoming SMTP message) 
    -- (zero indicates incoming attachments are NOT allowed) 
xcmCOInternetSMTPMaxOutAttachments -- SMTP Max Attachments (outgoing) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSMTP 62 } 
    -- integerNumber (0=none, or 1..n) 
    -- (max attachments for outgoing SMTP message) 
    -- (zero indicates outgoing attachments are NOT allowed) 

XCMI Working Group                File 52conftc                [Page 61]

Xerox Common Management Interface (XCMI) Standard               04/14/23

xcmCOInternetSMTPMaxInputSize   -- SMTP Max Message Size (incoming) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSMTP 63 } 
    -- integerNumber (bytes, 0=none, or 1..n) 
    -- (max size in bytes for incoming SMTP message) 
    -- (zero indicates incoming messages are NOT allowed) 
xcmCOInternetSMTPMaxOutputSize  -- SMTP Max Message Size (outgoing) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSMTP 64 } 
    -- integerNumber (bytes, 0=none, or 1..n) 
    -- (max size in bytes for outgoing SMTP message) 
    -- (zero indicates outgoing messages are NOT allowed) 
xcmCOInternetSMTPReversePath  -- SMTP Reverse Path 
    OBJECT IDENTIFIER ::= { xcmCOInternetSMTP 65 } 
    -- stringLocalization (RFC 822 format - 'user@hostname') 
    -- The reverse source routing list for SMTP mail. 
xcmCOInternetSMTPAutoServer -- Automatic SMTP Server detection 
   OBJECT IDENTIFIER ::= { xcmCOInternetSMTP 70 } 
   -- integerTruthValue 
   -- (true=enable automatic SMTP Server Detection, 
   --  false=disable auto detection) 


xcmCOInternetDNSDomainName      -- DNS Domain Name (directory) 
    OBJECT IDENTIFIER ::= { xcmCOInternetDNS 1 } 
    -- stringLocalization 
xcmCOInternetDNSLanguage        -- DNS Language (directory) 
    OBJECT IDENTIFIER ::= { xcmCOInternetDNS 3 } 
    -- stringLocalization (language tag, per RFC 2277) 
    -- (default is unknown language, per RFC 2277) 
xcmCOInternetDNSCharset         -- DNS Charset (directory) 
    OBJECT IDENTIFIER ::= { xcmCOInternetDNS 4 } 
    -- integerEnum (see 'CodedCharSet' in IETF Printer MIB) 
    -- (default '106' UTF-8, per RFC 2277 and RFC 2279) 
xcmCOInternetDNSServerName      -- DNS Server Name (directory) 
    OBJECT IDENTIFIER ::= { xcmCOInternetDNS 5 } 
    -- stringLocalization 

xcmCOInternetDNSServerAddress   -- DNS Server Address (directory) 
    OBJECT IDENTIFIER ::= { xcmCOInternetDNS 6 } 
    -- stringLocalization (IPv4 - dotted decimal 'a.b.c.d') 
    -- (see 'xcmCOInternetIPAddress' for references) 

xcmCOInternetDNSServerResolvedAddress  -- DNS Server Address (directory)
    OBJECT IDENTIFIER ::= { xcmCOInternetDNS 7 } 
    -- stringLocalization  
    -- address used by resolver (address may have been manually entered 
    -- or returned by DHCP server) 
    -- can be either IPv4 or IPv6 address 
    -- (IPv4 - dotted decimal 'a.b.c.d') 
    -- (see 'xcmCOInternetIPAddress' for references) 
    -- (IPv6 - hex w/ colons '[x1:...:x8/yyy]') 
    -- (see 'xcmCOInternetIPv6Address' for references) 

xcmCOInternetDNSServerTimeout   -- DNS Server Timeout 
    OBJECT IDENTIFIER ::= { xcmCOInternetDNS 8 } 

XCMI Working Group                File 52conftc                [Page 62]

Xerox Common Management Interface (XCMI) Standard               04/14/23

    -- integerNumber 
    -- value in seconds 

xcmCOInternetDNSAppendDomainName   -- DNS Append Domain Name 
    OBJECT IDENTIFIER ::= { xcmCOInternetDNS 9 } 
    -- integerTruthValue 
    -- (true=append domain name to hostname to resolve 
    --  unqualified hostnames) 

xcmCOInternetDNSAppendParentDomains  -- DNS Append Parent Domains 
    OBJECT IDENTIFIER ::= { xcmCOInternetDNS 10 } 
    -- integerTruthValue 
    -- (true=append parent domains to hostname to resolve 
    --  unqualified hostnames) 

xcmCOInternetDNSDomainNameList   -- DNS Domain Name List 
    OBJECT IDENTIFIER ::= { xcmCOInternetDNS 11 } 
    -- stringLocalization  
    -- Search list for hostname lookup 
    -- Prioritized list of domain names used to resolve 
    --  unqualified hostnames. 
    -- Linux limits the list to six domains with a total 
    --  of 256 characters. 

xcmCOInternetDNSDynamicUpdate   -- DNS Dynamic Update (directory) 
    OBJECT IDENTIFIER ::= { xcmCOInternetDNS 13 } 
    -- integerTruthValue 
    -- (true=enableDynamicUpdate, false=disableDynamicUpdate) 
    -- (see RFC 2136 'Dynamic Updates in DNS', April 1997) 
xcmCOInternetDNSUpdatePolicy    -- DNS Update Policy (directory) 
    OBJECT IDENTIFIER ::= { xcmCOInternetDNS 14 } 
    -- integerEnum 
    -- (1=lastUpdateWins, 2=firstUpdateWins) 
    -- (see RFC 2136 'Dynamic Updates in DNS', April 1997) 
xcmCOInternetDNSMulticastEnable  -- DNS Multicast Enable 
    OBJECT IDENTIFIER ::= { xcmCOInternetDNS 30 } 
    -- integerTruthValue (true=enableMDNS, false=disableMDNS) 
    -- (use of link local multicast DNS extensions) 
    -- (see 'draft-ietf-dnsext-mdns-03.txt', July 2001) 
    -- (see 'draft-guttman-dhc-mdns-enable-01.txt', July 2001) 
xcmCOInternetIOSDiscoveryEnable -- IOS Discovery Enable 
    OBJECT IDENTIFIER ::= { xcmCOInternetDNS 31 } 
    -- integerTruthValue (true=enableIOSDiscovery,  
    --                    false=disableIOSDiscovery) 
    -- (Apple IOS discovery advertisement) 


xcmCOInternetHTTPAddressURL     -- HTTP Universal Resource Locator (WWW)
    OBJECT IDENTIFIER ::= { xcmCOInternetHTTP 1 } 
    -- stringLocalization 
xcmCOInternetHTTPAddressURI     -- HTTP Universal Resource ID (WWW) 
    OBJECT IDENTIFIER ::= { xcmCOInternetHTTP 2 } 
    -- stringLocalization 
xcmCOInternetHTTPAddressURN     -- HTTP Universal Resource Name (WWW) 

XCMI Working Group                File 52conftc                [Page 63]

Xerox Common Management Interface (XCMI) Standard               04/14/23

    OBJECT IDENTIFIER ::= { xcmCOInternetHTTP 3 } 
    -- stringLocalization 
xcmCOInternetHTTPVersionString  -- HTTP Version String 
    OBJECT IDENTIFIER ::= { xcmCOInternetHTTP 9 } 
    -- stringLocalization (eg, '1.1' for HTTP/1.1, RFC 2616) 
xcmCOInternetHTTPListenSocket   -- HTTP Listen Socket 
    OBJECT IDENTIFIER ::= { xcmCOInternetHTTP 11 } 
    -- integerNumber (80=default or 1..n) 
    -- (see Internet Assigned Numbers, RFC 1700, and IANA registry) 
xcmCOInternetHTTPMaxClients     -- HTTP Max Clients (concurrently) 
    OBJECT IDENTIFIER ::= { xcmCOInternetHTTP 12 } 
    -- integerNumber (0..n) 
xcmCOInternetHTTPClientTimeout  -- HTTP Client Timeout (concurrently) 
    OBJECT IDENTIFIER ::= { xcmCOInternetHTTP 13 } 
    -- integerNumber (seconds, 0=infinite or 1..n) 
xcmCOInternetHTTPStatusRefresh  -- HTTP Status Refresh Delay 
    OBJECT IDENTIFIER ::= { xcmCOInternetHTTP 14 } 
    -- integerNumber (seconds, 0=infinite or 1..n) 
    -- The refresh delay used by CWIS when updating status 

xcmCOInternetHTTPAdminAddress  -- HTTP Admin Address 
    OBJECT IDENTIFIER ::= { xcmCOInternetHTTP 15 } 
    -- integerTruthValue(8) & stringLocalization(13) 
    -- The HTTP Administrator Accept Address 
    -- i.e. the Host Access List for HTTP/CWIS 

xcmCOInternetHTTPKeyUsrAddress  -- HTTP Key User Address 
    OBJECT IDENTIFIER ::= { xcmCOInternetHTTP 16 } 
    -- integerTruthValue(8) & stringLocalization(13) 
    -- The HTTP Key User Accept Address 
    -- i.e. the Host Access List for HTTP/CWIS 


xcmCOInternetHTTPProxy   -- HTTP Proxy enabled/disabled 
    OBJECT IDENTIFIER ::= { xcmCOInternetHTTP 20 } 

xcmCOInternetHTTPInfoFwd  -- HTTP Information Forwarding 
    OBJECT IDENTIFIER ::= { xcmCOInternetHTTP 25 } 
    -- integerTruthValue 
    -- (true=Information Forwarding to Xerox enabled, 
    --  false=Information Forwarding disabled) 
    -- When enabled information about model, install date, etc. 
    -- can be sent to Xerox. 
xcmCOInternetHTTPProxyIPAddress  -- HTTP Proxy IP address 
    OBJECT IDENTIFIER ::= { xcmCOInternetHTTPProxy 1 } 

xcmCOInternetHTTPProxyHostName  -- HTTP Proxy Host Name 
    OBJECT IDENTIFIER ::= { xcmCOInternetHTTPProxy 2 } 

xcmCOInternetHTTPProxyPortNumber   -- HTTP Proxy Port Number 
    OBJECT IDENTIFIER ::= { xcmCOInternetHTTPProxy 3 } 

xcmCOInternetHTTPProxyExceptions   -- HTTP Proxy Exceptions 
    OBJECT IDENTIFIER ::= { xcmCOInternetHTTPProxy 4 } 

XCMI Working Group                File 52conftc                [Page 64]

Xerox Common Management Interface (XCMI) Standard               04/14/23

    --  stringLocalization 
    --  Used to specify a list of addresses that do not require  
    --    the use of proxy. 
    --  Semicolons are used to separate entries. 
    --  Address lists that are longer than 255 characters require  
    --    multiple rows to be predefined in the CommsOption table.   
    --  The rows are related using the NextIndex, PreviousIndex  
    --    and FamilyIndex.   
    --  The FamilyIndex from the first   
    --    xcmCOInternetHTTPProxyExceptions node shall indicate the  
    --    next node.   
    --  The final node shall be identified using NextIndex  
    --     and FamilyIndex equal to zero. 
    --  It is the responsibility of the management tool to "get"  
    --     all rows and concatenate them for display.  
    --  It is the responsibility of the management tool to break  
    --     up the string into segments that are less than 255 to 
    --     "set" the rows. 

xcmCOInternetHTTPProxyServer      -- HTTP Proxy Server IP Address  
                                  --    or Host Name 
    OBJECT IDENTIFIER ::= { xcmCOInternetHTTPProxy 5 } 
    -- stringLocalization  
    -- The IP address or Host Name of the HTTP Proxy server. 

xcmCOInternetHTTPProxyUserName   -- HTTP Proxy User Name (for login) 
    OBJECT IDENTIFIER ::= { xcmCOInternetHTTPProxy 6 } 
    -- stringLocalization 
    -- (default user name for login to HTTP Proxy ) 

xcmCOInternetHTTPProxyPassword  -- HTTP Proxy Password (for login) 
    OBJECT IDENTIFIER ::= { xcmCOInternetHTTPProxy 7 } 
    -- stringLocalization (SHALL be encrypted) 
    -- (default password for login to HTTP Proxy ) 

xcmCOInternetHTTPProxyAutoDetect  -- HTTP Proxy Auto Detect 
    OBJECT IDENTIFIER ::= { xcmCOInternetHTTPProxy 8 } 
    -- integerTruthValue 
    -- (true=automatically check for and retrieve proxy server  
    --    if no valid proxy server is defined, 
    --  false=do not automatically check for valid proxy server) 

xcmCOInternetHTTPProxyShareSettings -- HTTP Proxy Shared Settings  
    OBJECT IDENTIFIER::= { xcmCOInternetHTTPProxy 9 } 
    -- integerTruthValue 
    -- Used to share the same Proxy settings for HTTP and HTTPS 

xcmCOInternetHTTPProxyAuthValid -- HTTP Proxy Authentication Valid  
    OBJECT IDENTIFIER::= { xcmCOInternetHTTPProxy 10 } 
    -- integerTruthValue 
    -- Used to determine if authentication is used for HTTP 


XCMI Working Group                File 52conftc                [Page 65]

Xerox Common Management Interface (XCMI) Standard               04/14/23


xcmCOInternetHTTPProxyUsePac -- HTTP Proxy Use PAC File URL   
    OBJECT IDENTIFIER::= { xcmCOInternetHTTPProxy 11 }  
    -- integerTruthValue  
    -- Used to determine if the proxy is set to use a URL for a PAC file

xcmCOInternetHTTPProxyPACURL -- HTTP Proxy PAC File URL   
    OBJECT IDENTIFIER::= { xcmCOInternetHTTPProxy 12 }  
    -- stringLocalization (0-256 characters)  
    -- Used to set the URL for a PAC File 


xcmCOInternetPOP3HostName       -- POP3 Host Name 
    OBJECT IDENTIFIER ::= { xcmCOInternetPOP3 1 } 
    -- stringLocalization 

xcmCOInternetPOP3HostAddress    -- POP3 Host Address 
    OBJECT IDENTIFIER ::= { xcmCOInternetPOP3 2 } 
    -- stringLocalization (IPv4 - dotted decimal 'a.b.c.d') 
    -- (see 'xcmCOInternetIPAddress' for references) 

xcmCOInternetPOP3PollInterval   -- POP3 Poll Interval 
    OBJECT IDENTIFIER ::= { xcmCOInternetPOP3 4 } 
    -- integerNumber (seconds, 0=immediate or 1..n) 
    -- (0=immediate - poll as frequently as application wishes) 
    -- (1..n=interval in seconds - SHOULD NOT be less than 3 seconds) 
    -- (max_int=poll once every 68 years - ie, disable polling) 
xcmCOInternetPOP3Subject        -- POP3 Subject (default) 
    OBJECT IDENTIFIER ::= { xcmCOInternetPOP3 44 } 
    -- stringLocalization 
    -- (default subject field for outgoing POP3 message) 
xcmCOInternetPOP3SignatureLine  -- POP3 Signature Line (default) 
    OBJECT IDENTIFIER ::= { xcmCOInternetPOP3 45 } 
    -- stringLocalization 
    -- (default signature line for outgoing POP3 message) 
xcmCOInternetPOP3UserName       -- POP3 User Name (for login to MTA) 
    OBJECT IDENTIFIER ::= { xcmCOInternetPOP3 47 } 
    -- stringLocalization 
    -- (default user name for login to remote MTA) 
xcmCOInternetPOP3Password       -- POP3 Password (for login to MTA) 
    OBJECT IDENTIFIER ::= { xcmCOInternetPOP3 48 } 
    -- stringLocalization (SHALL be encrypted) 
    -- (default password for login to remote MTA) 
xcmCOInternetPOP3MaxInputText   -- POP3 Max Text Body Size (incoming) 
    OBJECT IDENTIFIER ::= { xcmCOInternetPOP3 50 } 
    -- integerNumber (bytes, 0=none, or 1..n) 
    -- (max text body size for incoming POP3 message) 
    -- (value of zero indicates incoming text body is NOT allowed) 
xcmCOInternetPOP3MaxInputAttach -- POP3 Max Attachment Size (incoming) 
    OBJECT IDENTIFIER ::= { xcmCOInternetPOP3 51 } 
    -- integerNumber (bytes, 0=none, or 1..n) 
    -- (max attachment size for incoming POP3 message) 
    -- (value of zero indicates incoming attachment is NOT allowed) 
xcmCOInternetPOP3MaxOutputText  -- POP3 Max Text Body Size (outgoing) 

XCMI Working Group                File 52conftc                [Page 66]

Xerox Common Management Interface (XCMI) Standard               04/14/23

    OBJECT IDENTIFIER ::= { xcmCOInternetPOP3 52 } 
    -- integerNumber (bytes, 0=none, or 1..n) 
    -- (max text body size for outgoing POP3 message) 
    -- (value of zero indicates outgoing text body is NOT allowed) 
xcmCOInternetPOP3MaxOutputAttach -- POP3 Max Attachment Size (outgoing) 
    OBJECT IDENTIFIER ::= { xcmCOInternetPOP3 53 } 
    -- integerNumber (bytes, 0=none, or 1..n) 
    -- (max attachment size for outgoing POP3 message) 
    -- (value of zero indicates outgoing attachment is NOT allowed) 
xcmCOInternetPOP3ConfirmRequest -- POP3 Confirm Outgoing Email 
    OBJECT IDENTIFIER ::= { xcmCOInternetPOP3 54 } 
    -- integerTruthValue (true=enableMDN, false=disableMDN) 
xcmCOInternetPOP3ConfirmReply   -- POP3 Confirm Incoming Email 
    OBJECT IDENTIFIER ::= { xcmCOInternetPOP3 55 } 
    -- integerTruthValue (true=enableMDN, false=disableMDN) 
xcmCOInternetPOP3ConfirmTimeout -- POP3 Confirm Outgoing Timeout 
    OBJECT IDENTIFIER ::= { xcmCOInternetPOP3 56 } 
    -- integerNumber (seconds, 0=none, or 1..n) 
xcmCOInternetPOP3FeatureReply   -- POP3 Feature Report in Confirm Reply 
    OBJECT IDENTIFIER ::= { xcmCOInternetPOP3 57 } 
    -- integerTruthValue (true=enableReport, false=disableReport) 
xcmCOInternetPOP3MailAddress    -- POP3 Mail Address 
    OBJECT IDENTIFIER ::= { xcmCOInternetPOP3 58 } 
    -- stringLocalization (RFC 822 format - 'user@hostname') 
    -- (see RFC 822, 'Format of Internet Mail Messages', August, 1982) 
xcmCOInternetPOP3MaxInFragments -- POP3 Max Fragments (incoming) 
    OBJECT IDENTIFIER ::= { xcmCOInternetPOP3 59 } 
    -- integerNumber (0=none, or 2..n) 
    -- (max fragments for incoming POP3 message) 
    -- (zero indicates incoming fragments are NOT allowed) 
xcmCOInternetPOP3MaxOutFragments -- POP3 Max Fragments (outgoing) 
    OBJECT IDENTIFIER ::= { xcmCOInternetPOP3 60 } 
    -- integerNumber (0=none, or 2..n) 
    -- (max fragments for outgoing POP3 message) 
    -- (zero indicates outgoing fragments are NOT allowed) 
xcmCOInternetPOP3MaxInAttachments -- POP3 Max Attachments (incoming) 
    OBJECT IDENTIFIER ::= { xcmCOInternetPOP3 61 } 
    -- integerNumber (0=none, or 1..n) 
    -- (max attachments for incoming POP3 message) 
    -- (zero indicates incoming attachments are NOT allowed) 
xcmCOInternetPOP3MaxOutAttachments -- POP3 Max Attachments (outgoing) 
    OBJECT IDENTIFIER ::= { xcmCOInternetPOP3 62 } 
    -- integerNumber (0=none, or 1..n) 
    -- (max attachments for outgoing POP3 message) 
    -- (zero indicates outgoing attachments are NOT allowed) 
xcmCOInternetPOP3MaxInputSize   -- POP3 Max Message Size (incoming) 
    OBJECT IDENTIFIER ::= { xcmCOInternetPOP3 63 } 
    -- integerNumber (bytes, 0=none, or 1..n) 
    -- (max size in bytes for incoming POP3 message) 
    -- (zero indicates incoming messages are NOT allowed) 
xcmCOInternetPOP3MaxOutputSize  -- POP3 Max Message Size (outgoing) 
    OBJECT IDENTIFIER ::= { xcmCOInternetPOP3 64 } 
    -- integerNumber (bytes, 0=none, or 1..n) 
    -- (max size in bytes for outgoing POP3 message) 

XCMI Working Group                File 52conftc                [Page 67]

Xerox Common Management Interface (XCMI) Standard               04/14/23

    -- (zero indicates outgoing messages are NOT allowed) 

xcmCOInternetIMAP4HostName      -- IMAP4 Host Name 
    OBJECT IDENTIFIER ::= { xcmCOInternetIMAP4 1 } 
    -- stringLocalization 


xcmCOInternetIMAP4HostAddress   -- IMAP4 Host Address 
    OBJECT IDENTIFIER ::= { xcmCOInternetIMAP4 2 } 
    -- stringLocalization (IPv4 - dotted decimal 'a.b.c.d') 
    -- (see 'xcmCOInternetIPAddress' for references) 

xcmCOInternetIMAP4PollInterval  -- IMAP4 Poll Interval 
    OBJECT IDENTIFIER ::= { xcmCOInternetIMAP4 4 } 
    -- integerNumber (seconds, 0=immediate or 1..n) 
    -- (0=immediate - poll as frequently as application wishes) 
    -- (1..n=interval in seconds - SHOULD NOT be less than 3 seconds) 
    -- (max_int=poll once every 68 years - ie, disable polling) 
xcmCOInternetIMAP4Subject       -- IMAP4 Subject (default) 
    OBJECT IDENTIFIER ::= { xcmCOInternetIMAP4 44 } 
    -- stringLocalization 
    -- (default subject field for outgoing IMAP4 message) 
xcmCOInternetIMAP4SignatureLine -- IMAP4 Signature Line (default) 
    OBJECT IDENTIFIER ::= { xcmCOInternetIMAP4 45 } 
    -- stringLocalization 
    -- (default signature line for outgoing IMAP4 message) 
xcmCOInternetIMAP4UserName      -- IMAP4 User Name (for login to MTA) 
    OBJECT IDENTIFIER ::= { xcmCOInternetIMAP4 47 } 
    -- stringLocalization 
    -- (default user name for login to remote MTA) 
xcmCOInternetIMAP4Password      -- IMAP4 Password (for login to MTA) 
    OBJECT IDENTIFIER ::= { xcmCOInternetIMAP4 48 } 
    -- stringLocalization (SHALL be encrypted) 
    -- (default password for login to remote MTA) 
xcmCOInternetIMAP4MaxInputText  -- IMAP4 Max Text Body Size (incoming) 
    OBJECT IDENTIFIER ::= { xcmCOInternetIMAP4 50 } 
    -- integerNumber (bytes, 0=none, or 1..n) 
    -- (max text body size for incoming IMAP4 message) 
    -- (value of zero indicates incoming text body is NOT allowed) 
xcmCOInternetIMAP4MaxInputAttach -- IMAP4 Max Attachment Size (incoming)
    OBJECT IDENTIFIER ::= { xcmCOInternetIMAP4 51 } 
    -- integerNumber (bytes, 0=none, or 1..n) 
    -- (max attachment size for incoming IMAP4 message) 
    -- (value of zero indicates incoming attachment is NOT allowed) 
xcmCOInternetIMAP4MaxOutputText -- IMAP4 Max Text Body Size (outgoing) 
    OBJECT IDENTIFIER ::= { xcmCOInternetIMAP4 52 } 
    -- integerNumber (bytes, 0=none, or 1..n) 
    -- (max text body size for outgoing IMAP4 message) 
    -- (value of zero indicates outgoing text body is NOT allowed) 
xcmCOInternetIMAP4MaxOutputAttach -- IMAP4 Max Attach Size (outgoing) 
    OBJECT IDENTIFIER ::= { xcmCOInternetIMAP4 53 } 
    -- integerNumber (bytes, 0=none, or 1..n) 
    -- (max attachment size for outgoing IMAP4 message) 
    -- (value of zero indicates outgoing attachment is NOT allowed) 

XCMI Working Group                File 52conftc                [Page 68]

Xerox Common Management Interface (XCMI) Standard               04/14/23

xcmCOInternetIMAP4ConfirmRequest -- IMAP4 Confirm Outgoing Email 
    OBJECT IDENTIFIER ::= { xcmCOInternetIMAP4 54 } 
    -- integerTruthValue (true=enableMDN, false=disableMDN) 
xcmCOInternetIMAP4ConfirmReply  -- IMAP4 Confirm Incoming Email 
    OBJECT IDENTIFIER ::= { xcmCOInternetIMAP4 55 } 
    -- integerTruthValue (true=enableMDN, false=disableMDN) 
xcmCOInternetIMAP4ConfirmTimeout -- IMAP4 Confirm Outgoing Timeout 
    OBJECT IDENTIFIER ::= { xcmCOInternetIMAP4 56 } 
    -- integerNumber (seconds, 0=none, or 1..n) 
xcmCOInternetIMAP4FeatureReply  -- IMAP4 Feature Report in Confirm Reply
    OBJECT IDENTIFIER ::= { xcmCOInternetIMAP4 57 } 
    -- integerTruthValue (true=enableReport, false=disableReport) 
xcmCOInternetIMAP4MailAddress   -- IMAP4 Mail Address 
    OBJECT IDENTIFIER ::= { xcmCOInternetIMAP4 58 } 
    -- stringLocalization (RFC 822 format - 'user@hostname') 
    -- (see RFC 822, 'Format of Internet Mail Messages', August, 1982) 
xcmCOInternetIMAP4MaxInFragments -- IMAP4 Max Fragments (incoming) 
    OBJECT IDENTIFIER ::= { xcmCOInternetIMAP4 59 } 
    -- integerNumber (0=none, or 2..n) 
    -- (max fragments for incoming IMAP4 message) 
    -- (zero indicates incoming fragments are NOT allowed) 
xcmCOInternetIMAP4MaxOutFragments -- IMAP4 Max Fragments (outgoing) 
    OBJECT IDENTIFIER ::= { xcmCOInternetIMAP4 60 } 
    -- integerNumber (0=none, or 2..n) 
    -- (max fragments for outgoing IMAP4 message) 
    -- (zero indicates outgoing fragments are NOT allowed) 
xcmCOInternetIMAP4MaxInAttachments -- IMAP4 Max Attachments (incoming) 
    OBJECT IDENTIFIER ::= { xcmCOInternetIMAP4 61 } 
    -- integerNumber (0=none, or 1..n) 
    -- (max attachments for incoming IMAP4 message) 
    -- (zero indicates incoming attachments are NOT allowed) 
xcmCOInternetIMAP4MaxOutAttachments -- IMAP4 Max Attachments (outgoing) 
    OBJECT IDENTIFIER ::= { xcmCOInternetIMAP4 62 } 
    -- integerNumber (0=none, or 1..n) 
    -- (max attachments for outgoing IMAP4 message) 
    -- (zero indicates outgoing attachments are NOT allowed) 
xcmCOInternetIMAP4MaxInputSize   -- IMAP4 Max Message Size (incoming) 
    OBJECT IDENTIFIER ::= { xcmCOInternetIMAP4 63 } 
    -- integerNumber (bytes, 0=none, or 1..n) 
    -- (max size in bytes for incoming IMAP4 message) 
    -- (zero indicates incoming messages are NOT allowed) 
xcmCOInternetIMAP4MaxOutputSize  -- IMAP4 Max Message Size (outgoing) 
    OBJECT IDENTIFIER ::= { xcmCOInternetIMAP4 64 } 
    -- integerNumber (bytes, 0=none, or 1..n) 
    -- (max size in bytes for outgoing IMAP4 message) 
    -- (zero indicates outgoing messages are NOT allowed) 

xcmCOInternetNTPHostName        -- NTP Server hostname 
    OBJECT IDENTIFIER ::= { xcmCOInternetNTP 1 } 
    -- stringLocalization 

xcmCOInternetNTPHostAddress    -- NTP Server IP address 
    OBJECT IDENTIFIER ::= { xcmCOInternetNTP 2 } 
    -- stringLocalization (IPv4 dotted decimal 'a.b.c.d') 

XCMI Working Group                File 52conftc                [Page 69]

Xerox Common Management Interface (XCMI) Standard               04/14/23


xcmCOInternetNTPv6HostAddress   -- NTP Server IPv6 address 
    OBJECT IDENTIFIER ::= { xcmCOInternetNTP 3 } 
    -- stringLocalization (IPv6 - hex w/ colons '[x1:...:x8/yyy]') 
    -- (see 'xcmCOInternetIPv6Address' for references) 

xcmCOInternetNTPPort            -- NTP Port number 
    OBJECT IDENTIFIER ::= { xcmCOInternetNTP 4 } 
    -- integerNumber (1..999) 

xcmCOInternetNTPGMTOffset       -- NTP GMT offset 
    OBJECT IDENTIFIER ::= { xcmCOInternetNTP 5 } 
    -- integerNumber (-720..+780 minutes) 

xcmCOInternetNTPPollInterval    -- NTP Polling interval 
    OBJECT IDENTIFIER ::= { xcmCOInternetNTP 6 } 
    -- integerNumber (1..1440 minutes) 

xcmCOInternetNTPSkewTime        -- NTP Skew time 
    OBJECT IDENTIFIER ::= { xcmCOInternetNTP 7 } 
    -- integerNumber (1..300 minutes) 


xcmCOInternetWINSDomainName     -- WINS Domain Name (directory) 
    OBJECT IDENTIFIER ::= { xcmCOInternetWINS 1 } 
    -- stringLocalization 
xcmCOInternetWINSLanguage       -- WINS Language (directory) 
    OBJECT IDENTIFIER ::= { xcmCOInternetWINS 3 } 
    -- stringLocalization (language tag, per RFC 2277) 
    -- (default is unknown language, per RFC 2277) 
xcmCOInternetWINSCharset        -- WINS Charset (directory) 
    OBJECT IDENTIFIER ::= { xcmCOInternetWINS 4 } 
    -- integerEnum (see 'CodedCharSet' in IETF Printer MIB) 
    -- (default '106' UTF-8, per RFC 2277 and RFC 2279) 
xcmCOInternetWINSServerName     -- WINS Server Name (directory) 
    OBJECT IDENTIFIER ::= { xcmCOInternetWINS 5 } 
    -- stringLocalization 

xcmCOInternetWINSServerAddress  -- WINS Server Address (directory) 
    OBJECT IDENTIFIER ::= { xcmCOInternetWINS 6 } 
    -- stringLocalization (IPv4 - dotted decimal 'a.b.c.d') 
    -- (see 'xcmCOInternetIPAddress' for references) 

xcmCOInternetWINSServerSocket   -- WINS Server Socket (directory) 
    OBJECT IDENTIFIER ::= { xcmCOInternetWINS 7 } 
    -- integerNumber (1512=default or 1..n) 
    -- (see Internet Assigned Numbers, RFC 1700, and IANA registry) 

xcmCOInternetLDAPLanguage       -- LDAP Language (directory) 
    OBJECT IDENTIFIER ::= { xcmCOInternetLDAP 3 } 
    -- stringLocalization (language tag, per RFC 2277) 
    -- (default is unknown language, per RFC 2277) 
xcmCOInternetLDAPCharset        -- LDAP Charset (directory) 
    OBJECT IDENTIFIER ::= { xcmCOInternetLDAP 4 } 

XCMI Working Group                File 52conftc                [Page 70]

Xerox Common Management Interface (XCMI) Standard               04/14/23

    -- integerEnum (see 'CodedCharSet' in IETF Printer MIB) 
    -- (default '106' UTF-8, per RFC 2271, RFC 2277, RFC 2279) 
xcmCOInternetLDAPServerName     -- LDAP Server Name (directory) 
    OBJECT IDENTIFIER ::= { xcmCOInternetLDAP 5 } 
    -- stringLocalization 

xcmCOInternetLDAPServerAddress  -- LDAP Server Address (directory) 
    OBJECT IDENTIFIER ::= { xcmCOInternetLDAP 6 } 
    -- stringLocalization (IPv4 - dotted decimal 'a.b.c.d') 
    -- (see 'xcmCOInternetIPAddress' for references) 

xcmCOInternetLDAPServerSocket   -- LDAP Server Socket (directory) 
    OBJECT IDENTIFIER ::= { xcmCOInternetLDAP 7 } 
    -- integerNumber (389=default or 1..n) 
    -- (see Internet Assigned Numbers, RFC 1700, and IANA registry) 
xcmCOInternetLDAPPollInterval   -- LDAP Poll Interval (directory) 
    OBJECT IDENTIFIER ::= { xcmCOInternetLDAP 8 } 
    -- integerNumber (seconds, 0=immediate or 1..n) 
    -- (0=immediate - poll as frequently as application wishes) 
    -- (1..n=interval in seconds - SHOULD NOT be less than 3 seconds) 
    -- (max_int=poll once every 68 years - ie, disable polling) 
xcmCOInternetLDAPBindDN         -- LDAP Bind User Name (directory) 
    OBJECT IDENTIFIER ::= { xcmCOInternetLDAP 11 } 
    -- stringLocalization 
xcmCOInternetLDAPBindPassword   -- LDAP Bind Password (directory) 
    OBJECT IDENTIFIER ::= { xcmCOInternetLDAP 12 } 
    -- stringLocalization (SHALL be encrypted) 
xcmCOInternetLDAPBaseDN         -- LDAP Base Dist Name (directory) 
    OBJECT IDENTIFIER ::= { xcmCOInternetLDAP 13 } 
    -- stringLocalization 
xcmCOInternetLDAPPrinterName    -- LDAP Printer Name (directory) 
    OBJECT IDENTIFIER ::= { xcmCOInternetLDAP 21 } 
    -- stringLocalization 
xcmCOInternetLDAPPrinterClass   -- LDAP Printer Object Class (directory)
    OBJECT IDENTIFIER ::= { xcmCOInternetLDAP 22 } 
    -- stringLocalization 
xcmCOInternetLDAPAttributeName  -- LDAP Attribute Name (directory) 
    OBJECT IDENTIFIER ::= { xcmCOInternetLDAP 31 } 
    -- stringLocalization (name of attribute) 
xcmCOInternetLDAPAttributeType  -- LDAP Attribute Type (directory) 
    OBJECT IDENTIFIER ::= { xcmCOInternetLDAP 32 } 
    -- stringLocalization (data type of attribute) 
xcmCOInternetLDAPAttributeInt   -- LDAP Attribute Integer (directory) 
    OBJECT IDENTIFIER ::= { xcmCOInternetLDAP 33 } 
    -- integerNumber (according to type above) 
xcmCOInternetLDAPAttributeStr   -- LDAP Attribute String (directory) 
    OBJECT IDENTIFIER ::= { xcmCOInternetLDAP 34 } 
    -- stringLocalization (according to type) - value per SLPv2 
    -- integerEnum (XcmCommsLDAPAttributeType) - name and data type 
    -- (see 'XcmCommsLDAPAttributeType' for string encoding rules) 
xcmCOInternetLDAPMaxSearchResult -- LDAP Max Search Result (directory) 
    OBJECT IDENTIFIER ::= { xcmCOInternetLDAP 35 } 
    -- integerNumber (0..n) 
    -- (max search results - matching entries) 

XCMI Working Group                File 52conftc                [Page 71]

Xerox Common Management Interface (XCMI) Standard               04/14/23

xcmCOInternetLDAPSearchTimeout  -- LDAP Search Timeout (directory) 
    OBJECT IDENTIFIER ::= { xcmCOInternetLDAP 36 } 
    -- integerNumber (seconds, 0=infinite or 1..n) 

xcmCOInternetSSDPCacheTimeout   -- MS UPnP SSDP Cache Timeout 
    OBJECT IDENTIFIER ::= { xcmCOInternetUpnpSSDP 1 } 
    -- integerNumber (seconds, 0=none, or 1..n) 
    -- (max time to cache service advertisements) 
    -- (SHOULD default to 1800 seconds, per MS UPnP architecure specs) 
    -- (device SHOULD renew advertisement every CacheTimeout/4 seconds) 
xcmCOInternetSSDPTimeToLive     -- MS UPnP SSDP Time To Live 
    OBJECT IDENTIFIER ::= { xcmCOInternetUpnpSSDP 2 } 
    -- integerNumber (hops, 0=none, or 1..n) 
    -- (max hop count for SSDP messages) 
    -- (SHOULD default to 1 hop - link local only, per MS Win/ME) 
xcmCOInternetSSDPServerVersion  -- MS UPnP SSDP Server Version 
    OBJECT IDENTIFIER ::= { xcmCOInternetUpnpSSDP 3 } 
    -- stringLocalization (versions of OS, UPnP, and specific product) 
    -- (format 'OS/ver UPnP/ver ProductName/ver') 
    -- (eg, 'Linux/8.0 UPnP/1.0 DocuCentre/470') 

xcmCOInternetSLPLanguage        -- SLP Language (discovery) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSLP 3 } 
    -- stringLocalization (language tag, per RFC 2277) 
    -- (default is unknown language, per RFC 2277) 
xcmCOInternetSLPCharset         -- SLP Charset (discovery) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSLP 4 } 
    -- integerEnum (see 'CodedCharSet' in IETF Printer MIB) 
    -- (default '106' UTF-8, per RFC 2271, RFC 2277, RFC 2279) 
xcmCOInternetSLPServerName      -- SLP Server Name (discovery) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSLP 5 } 
    -- stringLocalization (see Directory Agent in IETF SLP) 

xcmCOInternetSLPServerAddress   -- SLP Server Address (discovery) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSLP 6 } 
    -- stringLocalization (IPv4 - dotted decimal 'a.b.c.d') 
    -- (see 'xcmCOInternetIPAddress' for references) 

xcmCOInternetSLPServerSocket    -- SLP Server Socket (discovery) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSLP 7 } 
    -- integerNumber (427=default or 1..n) 
    -- (see Internet Assigned Numbers, RFC 1700, and IANA registry) 
xcmCOInternetSLPPollInterval    -- SLP Poll Interval (discovery) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSLP 8 } 
    -- integerNumber (seconds, 0=immediate or 1..n) 
    -- (0=immediate - poll as frequently as application wishes) 
    -- (1..n=interval in seconds - SHOULD NOT be less than 3 seconds) 
    -- (max_int=poll once every 68 years - ie, disable polling) 
    -- (obsoleted by 'xcmCOInternetSLPDAFindActiveWait') 

--  SLPv2 (section 13, RFC 2608) and SLPv1 (section 22.2, RFC 2165) 
xcmCOInternetSLPMaxMulticastTime -- SLP Max Multicast Complete Time 
    OBJECT IDENTIFIER ::= { xcmCOInternetSLP 10 } 
    -- integerNumber (seconds, 0=none, or 1..n) 

XCMI Working Group                File 52conftc                [Page 72]

Xerox Common Management Interface (XCMI) Standard               04/14/23

    -- (max time to wait for a complete multicast query response) 
    -- (SHOULD default to 15 seconds, per SLPv2 RFC 2608) 
    -- (see SLPv2 RFC 2608 CONFIG_MAX_MC) 
    -- (see SLPv1 RFC 2165 CONFIG_INTERVAL_3) 
    -- (compare SLPv1 RFC 2165 CONFIG_INTERVAL_7) 
xcmCOInternetSLPDAFindStartWait  -- SLP DA Find Start Wait 
    OBJECT IDENTIFIER ::= { xcmCOInternetSLP 11 } 
    -- integerNumber (seconds, 0=none, or 1..n) 
    -- (interval to wait before starting DA discovery after SA reboot) 
    -- (SHOULD default to 3 seconds, per SLPv2 RFC 2608) 
    -- (see SLPv2 RFC 2608 CONFIG_START_WAIT) 
    -- (see SLPv1 RFC 2165 CONFIG_INTERVAL_4) 
xcmCOInternetSLPInitialRetryWait -- SLP Initial Request Retry Wait 
    OBJECT IDENTIFIER ::= { xcmCOInternetSLP 12 } 
    -- integerNumber (seconds, 0=none, or 1..n) 
    -- (interval to wait before initial retry of multicast or unicast) 
    -- (SHOULD default to 2 seconds, per SLPv2 RFC 2608) 
    -- (see SLPv2 RFC 2608 CONFIG_RETRY) 
    -- (see SLPv1 RFC 2165 CONFIG_INTERVAL_2) 
    -- (compare SLPv1 RFC 2165 CONFIG_INTERVAL_5) 
    -- (compare SLPv1 RFC 2165 CONFIG_INTERVAL_6) 
xcmCOInternetSLPMaxUnicastTime   -- SLP Max Unicast Complete Time 
    OBJECT IDENTIFIER ::= { xcmCOInternetSLP 13 } 
    -- integerNumber (seconds, 0=none, or 1..n) 
    -- (max time to wait for a complete unicast query response) 
    -- (SHOULD default to 15 seconds, per SLPv2 RFC 2608) 
    -- (see SLPv2 RFC 2608 CONFIG_RETRY_MAX) 
    -- (see SLPv1 RFC 2165 CONFIG_INTERVAL_8) 
    -- (compare SLPv1 RFC 2165 CONFIG_INTERVAL_8) 
xcmCOInternetSLPDAHeartbeatTime  -- SLP DA Heartbeat Time 
    OBJECT IDENTIFIER ::= { xcmCOInternetSLP 14 } 
    -- integerNumber (seconds, 0=none, or 1..n) 
    -- (interval to wait before DA multicast/broadcast DAAdvert) 
    -- (SHOULD default to 10800 seconds [3 hours], per SLPv2 RFC 2608) 
    -- (see SLPv2 RFC 2608 CONFIG_DA_BEAT) 
    -- (see SLPv1 RFC 2165 CONFIG_INTERVAL_9) 
xcmCOInternetSLPDAFindActiveWait -- SLP DA Find Active Retry Wait 
    OBJECT IDENTIFIER ::= { xcmCOInternetSLP 15 } 
    -- integerNumber (seconds, 0=none, or 1..n) 
    -- (interval to wait before retry of active DA discovery) 
    -- (SHOULD default to 900 seconds [15 minutes], per SLPv2 RFC 2608) 
    -- (see SLPv2 RFC 2608 CONFIG_DA_FIND) 
    -- (no SLPv1 RFC 2165 equivalent configuration) 
    -- (obsoletes 'xcmCOInternetSLPPollInterval' above) 
xcmCOInternetSLPRegPassiveWait   -- SLP Register After Passive Find Wait
    OBJECT IDENTIFIER ::= { xcmCOInternetSLP 16 } 
    -- integerNumber (seconds, 0=none, or 1..n) 
    -- (interval to wait before registration after passive DA discovery)
    -- (SHOULD default to 1-3 seconds, per SLPv2 RFC 2608) 
    -- (see SLPv2 RFC 2608 CONFIG_REG_PASSIVE) 
    -- (see SLPv1 RFC 2165 CONFIG_INTERVAL_10) 
xcmCOInternetSLPRegActiveWait    -- SLP Register After Active Find Wait 
    OBJECT IDENTIFIER ::= { xcmCOInternetSLP 17 } 
    -- integerNumber (seconds, 0=none, or 1..n) 

XCMI Working Group                File 52conftc                [Page 73]

Xerox Common Management Interface (XCMI) Standard               04/14/23

    -- (interval to wait before registration after active DA discovery) 
    -- (SHOULD default to 1-3 seconds, per SLPv2 RFC 2608) 
    -- (see SLPv2 RFC 2608 CONFIG_REG_ACTIVE) 
    -- (see SLPv1 RFC 2165 CONFIG_INTERVAL_11) 
xcmCOInternetSLPCloseConnWait    -- SLP Close Idle Connection Wait 
    OBJECT IDENTIFIER ::= { xcmCOInternetSLP 18 } 
    -- integerNumber (seconds, 0=none, or 1..n) 
    -- (interval to wait before DAs and SAs close idle connection) 
    -- (SHOULD default to 300 seconds [5 minutes], per SLPv2 RFC 2608) 
    -- (see SLPv2 RFC 2608 CONFIG_CLOSE_CONN) 
    -- (see SLPv1 RFC 2165 CONFIG_INTERVAL_12) 
xcmCOInternetSLPCacheReplyTime   -- SLPv1 Cache Reply by XID Time 
    OBJECT IDENTIFIER ::= { xcmCOInternetSLP 20 } 
    -- integerNumber (seconds, 0=none, or 1..n) 
    -- (max time to cache responses by XID before discarding) 
    -- (SHOULD default to 60 seconds, per SLPv1 RFC 2165) 
    -- (see SLPv1 RFC 2165 CONFIG_INTERVAL_0) 
xcmCOInternetSLPMaxRegLifetime   -- SLPv1 Max Registration Lifetime 
    OBJECT IDENTIFIER ::= { xcmCOInternetSLP 21 } 
    -- integerNumber (seconds, 0=none, or 1..n) 
    -- (max lifetime of registrations before expiration) 
    -- (SHOULD default to 10800 seconds, per SLPv1 RFC 2165) 
    -- (see SLPv1 RFC 2165 CONFIG_INTERVAL_1) 
xcmCOInternetSLPDAFindRetryWait  -- SLP DA Find Retry Wait 
    OBJECT IDENTIFIER ::= { xcmCOInternetSLP 22 } 
    -- integerNumber (seconds, 0=none, or 1..n) 
    -- (interval to wait before retransmit DA discovery) 
    -- (SHOULD default to 3 seconds, per SLPv1 RFC 2165) 
    -- (compare SLPv2 RFC 2608 CONFIG_RETRY) 
    -- (see SLPv1 RFC 2165 CONFIG_INTERVAL_5) 
xcmCOInternetSLPMaxDARequestTime -- SLP Max DA Request Time 
    OBJECT IDENTIFIER ::= { xcmCOInternetSLP 23 } 
    -- integerNumber (seconds, 0=none, or 1..n) 
    -- (interval to wait before DA request timeout) 
    -- (SHOULD default to 5 seconds, per SLPv1 RFC 2165) 
    -- (compare SLPv2 RFC 2608 CONFIG_RETRY) 
    -- (see SLPv1 RFC 2165 CONFIG_INTERVAL_6) 
xcmCOInternetSLPMulticastEnable  -- SLP Multicast Enable 
    OBJECT IDENTIFIER ::= { xcmCOInternetSLP 30 } 
    -- integerTruthValue (true=useMulticast, false=useBroadcast) 
    -- (use of multicast [scalable] versus broadcast [non-scalable]) 
    -- (SHOULD default to 'true', per SLPv1 RFC 2165) 
    -- (SHOULD default to 'true', per SLPv2 RFC 2608) 
xcmCOInternetSLPMulticastRadius  -- SLP Multicast Radius (hop count) 
    OBJECT IDENTIFIER ::= { xcmCOInternetSLP 31 } 
    -- integerNumber (0..255) 
    -- (multicast/broadcast radius) 
    -- (SHOULD default to 32, per SLPv1 RFC 2165) 
    -- (range '0..32' for SLPv1 RFC 2165) 
    -- (range '0..255' for SLPv2 RFC 2608) 
xcmCOInternetSLPPathMTUSize      -- SLP Path MTU Size 
    OBJECT IDENTIFIER ::= { xcmCOInternetSLP 32 } 
    -- integerNumber (0..n) 
    -- (path max transmission unit size in bytes) 

XCMI Working Group                File 52conftc                [Page 74]

Xerox Common Management Interface (XCMI) Standard               04/14/23

    -- (SHOULD default to 1400, per SLPv1 RFC 2165) 
xcmCOInternetSLPScopeName        -- SLP Scope Name 
    OBJECT IDENTIFIER ::= { xcmCOInternetSLP 40 } 
    -- stringLocalization 
    -- (configured scope name) 
    -- (SHOULD default to 'DEFAULT', per SLPv2 RFC 2608) 
xcmCOInternetSLPScopeKey         -- SLP Scope Key 
    OBJECT IDENTIFIER ::= { xcmCOInternetSLP 41 } 
    -- stringLocalization (SHALL be encrypted) 
    -- (configured protected scope key) 
    -- (see section 22, SLPv1 RFC 2165) 
xcmCOInternetSLPAttributesEnable  -- SLP Attributes Enable 
    OBJECT IDENTIFIER ::= { xcmCOInternetSLP 50 } 
    -- integerTruthValue 
    -- (true=enable SLP Attributes support, 
    --  false=disable SLP Attributes support) 


xcmCOInternetOsfDceKerberosRealm -- OSF DCE Kerberos Realm (security) 
    OBJECT IDENTIFIER ::= { xcmCOInternetOsfDceKerberos 1 } 
    -- stringLocalization 

-- 
--          AppleTalk Protocol Suite 
-- 

xcmCOAppletalkSuite 
    OBJECT IDENTIFIER ::= { xcmCommsConfigTC 18 } 
    -- integerTruthValue 

xcmCOAppletalkDatalinks 
    OBJECT IDENTIFIER ::= { xcmCOAppletalkSuite 1200 } 
    -- integerTruthValue (w/ chain of 'xcmCOOsilan...') 
    -- (obsoletes 'xcmCOAppletalkDDPDatalinks') 
xcmCOAppletalkLLAP              -- LocalTalk LAP (datalink) 
    OBJECT IDENTIFIER ::= { xcmCOAppletalkSuite 1201 } 
    -- integerTruthValue 
xcmCOAppletalkELAP              -- EtherTalk LAP (datalink) 
    OBJECT IDENTIFIER ::= { xcmCOAppletalkSuite 1202 } 
    -- integerTruthValue 
xcmCOAppletalkTLAP              -- TokenTalk LAP (datalink) 
    OBJECT IDENTIFIER ::= { xcmCOAppletalkSuite 1203 } 
    -- integerTruthValue 
xcmCOAppletalkPhase             -- AppleTalk Phase (datalink) 
    OBJECT IDENTIFIER ::= { xcmCOAppletalkSuite 1211 } 
    -- integerEnum (1=phase1, 2=phase2) 

xcmCOAppletalkTransports 
    OBJECT IDENTIFIER ::= { xcmCOAppletalkSuite 1400 } 
    -- integerTruthValue 
xcmCOAppletalkDDP               -- DDP (CL network) 
    OBJECT IDENTIFIER ::= { xcmCOAppletalkSuite 1301 } 
    -- integerTruthValue 
xcmCOAppletalkAARP              -- AARP (routing) 

XCMI Working Group                File 52conftc                [Page 75]

Xerox Common Management Interface (XCMI) Standard               04/14/23

    OBJECT IDENTIFIER ::= { xcmCOAppletalkSuite 1303 } 
    -- integerTruthValue 
xcmCOAppletalkATP               -- ATP (CL transport) 
    OBJECT IDENTIFIER ::= { xcmCOAppletalkSuite 1401 } 
    -- integerTruthValue 
xcmCOAppletalkADSP              -- ADSP (CO transport) 
    OBJECT IDENTIFIER ::= { xcmCOAppletalkSuite 1402 } 
    -- integerTruthValue 
xcmCOAppletalkRTMP              -- RTMP (routing) 
    OBJECT IDENTIFIER ::= { xcmCOAppletalkSuite 1403 } 
    -- integerTruthValue 
xcmCOAppletalkAEP               -- AEP (echo) 
    OBJECT IDENTIFIER ::= { xcmCOAppletalkSuite 1404 } 
    -- integerTruthValue 
xcmCOAppletalkNBP               -- NBP (directory) 
    OBJECT IDENTIFIER ::= { xcmCOAppletalkSuite 1405 } 
    -- integerTruthValue 

xcmCOAppletalkDDPAddress        -- DDP Node Address 
    OBJECT IDENTIFIER ::= { xcmCOAppletalkDDP 1 } 
    -- stringLocalization (dotted hex format, 'network.node') 
    -- ('network' [4 octets] - ASCII hex of 2-octet AppleTalk network) 
    -- ('node'    [2 octets] - ASCII hex of 1-octet AppleTalk node) 
xcmCOAppletalkDDPSocketAddress  -- DDP Socket Address 
    OBJECT IDENTIFIER ::= { xcmCOAppletalkDDPAddress 1 } 
    -- stringLocalization (dotted hex format, 'network.node.socket') 
    -- ('network' [4 octets] - ASCII hex of 2-octet AppleTalk network) 
    -- ('node'    [2 octets] - ASCII hex of 1-octet AppleTalk node) 
    -- ('socket'  [2 octets] - ASCII hex of 1-octet AppleTalk socket) 
xcmCOAppletalkDDPDatalinks      -- DDP Datalinks 
    OBJECT IDENTIFIER ::= { xcmCOAppletalkDDP 12 } 
    -- integerTruthValue (w/ chain of 'xcmCOOsilan...') 
    -- (obsoleted by 'xcmCOAppletalkDatalinks') 

xcmCOAppletalkNBPHostName       -- NBP Host Name (directory) 
    OBJECT IDENTIFIER ::= { xcmCOAppletalkNBP 1 } 
    -- stringLocalization (AppleTalk name is 'Object:Type@Zone') 
    -- (restricted to 'AppleASCII' chars, per Apple 'Inside Macintosh') 
xcmCOAppletalkNBPLanguage       -- NBP Language (directory) 
    OBJECT IDENTIFIER ::= { xcmCOAppletalkNBP 3 } 
    -- stringLocalization (language tag, per RFC 2277) 
    -- (default is unknown language, per RFC 2277) 
xcmCOAppletalkNBPCharset        -- NBP Charset (directory) 
    OBJECT IDENTIFIER ::= { xcmCOAppletalkNBP 4 } 
    -- integerEnum (see 'CodedCharSet' in IETF Printer MIB) 
    -- (default '106' UTF-8, per RFC 2277, RFC 2279) 
    -- (restricted to 'AppleASCII' chars, per Apple 'Inside Macintosh') 
xcmCOAppletalkNBPObject         -- NBP Object (directory) 
    OBJECT IDENTIFIER ::= { xcmCOAppletalkNBP 11 } 
    -- stringLocalization 
    -- (restricted to 'AppleASCII' chars, per Apple 'Inside Macintosh') 
xcmCOAppletalkNBPType           -- NBP Type (directory) 
    OBJECT IDENTIFIER ::= { xcmCOAppletalkNBP 12 } 
    -- stringLocalization ('LaserWriter'=default) 

XCMI Working Group                File 52conftc                [Page 76]

Xerox Common Management Interface (XCMI) Standard               04/14/23

    -- (restricted to 'AppleASCII' chars, per Apple 'Inside Macintosh') 
xcmCOAppletalkNBPZone           -- NBP Zone (directory) 
    OBJECT IDENTIFIER ::= { xcmCOAppletalkNBP 13 } 
    -- stringLocalization 
    -- (restricted to 'AppleASCII' chars, per Apple 'Inside Macintosh') 
xcmCOAppletalkNBPNetwork        -- NBP Network (directory) 
    OBJECT IDENTIFIER ::= { xcmCOAppletalkNBP 21 } 
    -- integerNumber (0..65534) 
xcmCOAppletalkNBPNode           -- NBP Node (directory) 
    OBJECT IDENTIFIER ::= { xcmCOAppletalkNBP 22 } 
    -- integerNumber (0..254) 
xcmCOAppletalkNBPSocket         -- NBP Socket (directory) 
    OBJECT IDENTIFIER ::= { xcmCOAppletalkNBP 23 } 
    -- integerNumber (0..254) 
xcmCOAppletalkNBPZoneToNetworks -- NBP Zone to Networks (directory) 
    OBJECT IDENTIFIER ::= { xcmCOAppletalkNBP 31 } 
    -- stringLocalization (dotted string 'zone.netFirst.netLast') 

xcmCOAppletalkApplications 
    OBJECT IDENTIFIER ::= { xcmCOAppletalkSuite 1700 } 
    -- integerTruthValue 
xcmCOAppletalkASP               -- ASP (CO session) 
    OBJECT IDENTIFIER ::= { xcmCOAppletalkSuite 1501 } 
    -- integerTruthValue 
xcmCOAppletalkZIP               -- ZIP (directory) 
    OBJECT IDENTIFIER ::= { xcmCOAppletalkSuite 1502 } 
    -- integerTruthValue 
xcmCOAppletalkPAP               -- PAP (printing) 
    OBJECT IDENTIFIER ::= { xcmCOAppletalkSuite 1503 } 
    -- integerTruthValue 

xcmCOAppletalkSNMP              -- SNMP (network mgmt) 
    OBJECT IDENTIFIER ::= { xcmCOAppletalkSuite 1510 } 
    -- integerTruthValue 
xcmCOAppletalkSNMPv1            -- SNMPv1 (network mgmt) 
    OBJECT IDENTIFIER ::= { xcmCOAppletalkSuite 1511 } 
    -- integerTruthValue 
xcmCOAppletalkSNMPv2            -- SNMPv2 (network mgmt) 
    OBJECT IDENTIFIER ::= { xcmCOAppletalkSuite 1512 } 
    -- integerTruthValue 
xcmCOAppletalkSNMPv3            -- SNMPv3 (network mgmt) 
    OBJECT IDENTIFIER ::= { xcmCOAppletalkSuite 1513 } 
    -- integerTruthValue 

xcmCOAppletalkAFP               -- AFP (filing) 
    OBJECT IDENTIFIER ::= { xcmCOAppletalkSuite 1601 } 
    -- integerTruthValue 
xcmCOAppletalkPS                -- PostScript (printing) 
    OBJECT IDENTIFIER ::= { xcmCOAppletalkSuite 1602 } 
    -- integerTruthValue 

xcmCOAppletalkPAPHostName       -- PAP Host Name 
    OBJECT IDENTIFIER ::= { xcmCOAppletalkPAP 1 } 
    -- stringLocalization (AppleTalk name is 'Object:Type@Zone') 

XCMI Working Group                File 52conftc                [Page 77]

Xerox Common Management Interface (XCMI) Standard               04/14/23

xcmCOAppletalkPAPHostAddress    -- PAP Host Address 
    OBJECT IDENTIFIER ::= { xcmCOAppletalkPAP 2 } 
    -- stringLocalization (dotted hex format, 'network.node.socket') 
xcmCOAppletalkPAPListenSocket   -- PAP Listen Socket 
    OBJECT IDENTIFIER ::= { xcmCOAppletalkPAP 3 } 
    -- integerNumber (140=default or 3..255) 
xcmCOAppletalkPAPMaxClients     -- PAP Max Clients (concurrently) 
    OBJECT IDENTIFIER ::= { xcmCOAppletalkPAP 4 } 
    -- integerNumber (0..n) 
xcmCOAppletalkPAPMaxPrinters    -- PAP Max Printers (printing) 
    OBJECT IDENTIFIER ::= { xcmCOAppletalkPAP 5 } 
    -- integerNumber (1=default or 1..n) 
xcmCOAppletalkPAPObject         -- PAP Object (printing) 
    OBJECT IDENTIFIER ::= { xcmCOAppletalkPAP 11 } 
    -- stringLocalization 
    -- (restricted to 'AppleASCII' chars, per Apple 'Inside Macintosh') 
xcmCOAppletalkPAPType           -- PAP Type (printing) 
    OBJECT IDENTIFIER ::= { xcmCOAppletalkPAP 12 } 
    -- stringLocalization ('LaserWriter'=default) 
    -- (restricted to 'AppleASCII' chars, per Apple 'Inside Macintosh') 
xcmCOAppletalkPAPZone           -- PAP Zone (printing) 
    OBJECT IDENTIFIER ::= { xcmCOAppletalkPAP 13 } 
    -- stringLocalization 
    -- (restricted to 'AppleASCII' chars, per Apple 'Inside Macintosh') 
xcmCOAppletalkPAPNetwork        -- PAP Network (printing) 
    OBJECT IDENTIFIER ::= { xcmCOAppletalkPAP 21 } 
    -- integerNumber (0..65534) 
xcmCOAppletalkPAPNode           -- PAP Node (printing) 
    OBJECT IDENTIFIER ::= { xcmCOAppletalkPAP 22 } 
    -- integerNumber (0..254) 
xcmCOAppletalkPAPSpool          -- PAP Spool (printing) 
    OBJECT IDENTIFIER ::= { xcmCOAppletalkPAP 31 } 
    -- integerEnum (1=none, 2=other, 3=disk, 4=ram) 
xcmCOAppletalkPAPMaxSpool       -- PAP Max Spool (printing) 
    OBJECT IDENTIFIER ::= { xcmCOAppletalkPAP 32 } 
    -- integerNumber (spool area size in bytes, 0..n) 
xcmCOAppletalkPAPJobTimeout     -- PAP Job Timeout (printing) 
    OBJECT IDENTIFIER ::= { xcmCOAppletalkPAP 40 } 
    -- integerNumber (seconds, 0=infinite or 1..n) 
xcmCOAppletalkPAPAutoSwitch     -- PAP Auto Switch (printing) 
    OBJECT IDENTIFIER ::= { xcmCOAppletalkPAP 41 } 
    -- integerEnum (see 'xcmCODirectPrintProtocol' below) 
xcmCOAppletalkPAPBinaryPS       -- PAP Binary PS (printing) 
    OBJECT IDENTIFIER ::= { xcmCOAppletalkPAP 42 } 
    -- integerTruthValue (true=enableBinaryPS, false=disableBinaryPS) 
    -- (interpret all PostScript jobs as binary - ignore control chars) 
    -- (PostScript per job submission protocol or 'xxxDefaultPDL' below)
xcmCOAppletalkPAPDefaultPDL     -- PAP Default PDL (printing) 
    OBJECT IDENTIFIER ::= { xcmCOAppletalkPAP 43 } 
    -- integerEnum ('XcmPrtInterpreterLangFamily' in XCMI Prt Ext TC) 
    -- (fixed PDL if 'xxxAutoSwitch' is 'none' or 'other') 
    -- (default PDL if 'xxxAutoSwitch' is 'autoSwitch') 
    -- (ignored if 'xxxAutoSwitch' is 'ps...' or 'hp...') 
    -- See: 'prtInterpreterLangFamily' in IETF Printer MIB (RFC 1759) 

XCMI Working Group                File 52conftc                [Page 78]

Xerox Common Management Interface (XCMI) Standard               04/14/23

    -- See: 'prtChannelDefaultPageDescLangIndex' (default PDL via value 
    --      of 'prtInterpreterIndex') in IETF Printer MIB (RFC 1759) 

-- 
--          NetWare Protocol Suite 
-- 

xcmCONetwareSuite 
    OBJECT IDENTIFIER ::= { xcmCommsConfigTC 19 } 
    -- integerTruthValue 

xcmCONetwareDatalinks 
    OBJECT IDENTIFIER ::= { xcmCONetwareSuite 1200 } 
    -- integerTruthValue (w/ chain of 'xcmCOOsilan...') 
    -- (obsoletes 'xcmCONetwareIPXDatalinks') 

xcmCONetwareTransports 
    OBJECT IDENTIFIER ::= { xcmCONetwareSuite 1400 } 
    -- integerTruthValue 
xcmCONetwareIPX                 -- IPX (CL network) 
    OBJECT IDENTIFIER ::= { xcmCONetwareSuite 1301 } 
    -- integerTruthValue 
xcmCONetwareIP                -- IP Network Layer. 
OBJECT IDENTIFIER  ::= {xcmCONetwareSuite 1302}     
    -- integerTruthValue (true=Netware communicating via IP,  
    -- false=Netware not communicating via IP) 
xcmCONetwareSPX                 -- SPX (CO transport) 
    OBJECT IDENTIFIER ::= { xcmCONetwareSuite 1402 } 
    -- integerTruthValue 
xcmCONetwareRIP                 -- RIP (routing) 
    OBJECT IDENTIFIER ::= { xcmCONetwareSuite 1403 } 
    -- integerTruthValue 
xcmCONetwareEcho                -- Echo (echo) 
    OBJECT IDENTIFIER ::= { xcmCONetwareSuite 1404 } 
    -- integerTruthValue 

xcmCONetwareIPXAddress          -- IPX Node Address 
    OBJECT IDENTIFIER ::= { xcmCONetwareIPX 1 } 
    -- stringLocalization (dotted hex format, 'network.node') 
    -- ('network' [8 octets] - unique network ID, '0' means 'local net')
    -- ('node'    [12 octets] - ASCII hex of IEEE 802.x MAC address) 
xcmCONetwareIPXSocketAddress    -- IPX Socket Address 
    OBJECT IDENTIFIER ::= { xcmCONetwareIPXAddress 1 } 
    -- stringLocalization (dotted hex format, 'network.node.socket') 
    -- ('network' [8 octets] - unique network ID, '0' means 'local net')
    -- ('node'    [12 octets] - ASCII hex of IEEE 802.x MAC address) 
    -- ('socket'  [4 octets] - ASCII hex of 2-octet NetWare socket) 
xcmCONetwareIPXDatalinks        -- IPX Datalinks 
    OBJECT IDENTIFIER ::= { xcmCONetwareIPX 12 } 
    -- integerTruthValue (w/ chain of 'xcmCOOsilan...') 
    -- (obsoleted by 'xcmCONetwareDatalinks') 

xcmCONetwareApplications 
    OBJECT IDENTIFIER ::= { xcmCONetwareSuite 1700 } 

XCMI Working Group                File 52conftc                [Page 79]

Xerox Common Management Interface (XCMI) Standard               04/14/23

    -- integerTruthValue 
xcmCONetwareNCP                 -- NCP (core protocols) 
    OBJECT IDENTIFIER ::= { xcmCONetwareSuite 1501 } 
    -- integerTruthValue 
xcmCONetwareNetbios             -- NetBIOS Emulation 
    OBJECT IDENTIFIER ::= { xcmCONetwareSuite 1502 } 
    -- integerTruthValue 
xcmCONetwarePServer             -- PServer (printing) 
    OBJECT IDENTIFIER ::= { xcmCONetwareSuite 1503 } 
    -- integerTruthValue 
xcmCONetwareFServer             -- FServer (filing) 
    OBJECT IDENTIFIER ::= { xcmCONetwareSuite 1504 } 
    -- integerTruthValue 
xcmCONetwareMHS                 -- MHS (email) 
    OBJECT IDENTIFIER ::= { xcmCONetwareSuite 1505 } 
    -- integerTruthValue 
xcmCONetwareBindery             -- Bindery (directory) 
    OBJECT IDENTIFIER ::= { xcmCONetwareSuite 1507 } 
    -- integerTruthValue 
xcmCONetwareNDS                 -- NDS (directory) 
    OBJECT IDENTIFIER ::= { xcmCONetwareSuite 1508 } 
    -- integerTruthValue 
xcmCONetwareRPrinter            -- RPrinter (printing) 
    OBJECT IDENTIFIER ::= { xcmCONetwareSuite 1509 } 
    -- integerTruthValue 

xcmCONetwareSNMP                -- SNMP (network mgmt) 
    OBJECT IDENTIFIER ::= { xcmCONetwareSuite 1510 } 
    -- integerTruthValue 
xcmCONetwareSNMPv1              -- SNMPv1 (network mgmt) 
    OBJECT IDENTIFIER ::= { xcmCONetwareSuite 1511 } 
    -- integerTruthValue 
xcmCONetwareSNMPv2              -- SNMPv2 (network mgmt) 
    OBJECT IDENTIFIER ::= { xcmCONetwareSuite 1512 } 
    -- integerTruthValue 
xcmCONetwareSNMPv3              -- SNMPv3 (network mgmt) 
    OBJECT IDENTIFIER ::= { xcmCONetwareSuite 1513 } 
    -- integerTruthValue 

xcmCONetwareSAP                 -- SAP (discovery) 
    OBJECT IDENTIFIER ::= { xcmCONetwareSuite 1591 } 
    -- integerTruthValue 

xcmCONetwareNDSIP                 -- Netware over IP 
    OBJECT IDENTIFIER ::= { xcmCONetwareSuite 1600 } 
    -- integerTruthValue 
    -- (true = enabled; false= disabled ) 

xcmCONetwareNDSIPHostname         
    -- Novell server hostname used to find tree & context for filing 
    OBJECT IDENTIFIER ::= { xcmCONetwareNDSIP 1 } 
    -- stringLocalization 

xcmCONetwareNDSIPAddress                 

XCMI Working Group                File 52conftc                [Page 80]

Xerox Common Management Interface (XCMI) Standard               04/14/23

    -- Novell server IP address used to find tree & context for filing 
    OBJECT IDENTIFIER ::= { xcmCONetwareNDSIP 2 } 
    -- stringLocalization (IPv4 - dotted decimal 'a.b.c.d') 
    -- <or> 
    -- stringLocalization (IPv6 - hex w/ colons '[x1:...:x8]') 
    -- (IPv4 - decimal values [1-3 octets] of four 8-bit components) 
    -- (eg, '13.226.19.10') 
    -- (IPv6 - eight hex values [0-4 octets] of 16-bit components) 

xcmCONetwareNDSIPUseHostname          -- to choose Hostname or IPAddress
    OBJECT IDENTIFIER ::= { xcmCONetwareNDSIP 3 } 
    -- integerTruthValue 
    -- (true = Hostname; false= IPAddress ) 

xcmCONetwarePServerName         -- PServer Name (printing) 
    OBJECT IDENTIFIER ::= { xcmCONetwarePServer 1 } 
    -- stringLocalization 
    -- (compare with 'xcmCONetware[RPrinter|SAPUnit]Name') 
xcmCONetwarePServerPassword     -- PServer Password (printing) 
    OBJECT IDENTIFIER ::= { xcmCONetwarePServer 2 } 
    -- stringLocalization (SHALL be encrypted) 
xcmCONetwarePServerQueueName    -- PServer Queue Name (printing) 
    OBJECT IDENTIFIER ::= { xcmCONetwarePServer 3 } 
    -- stringLocalization 
xcmCONetwarePServerPollInterval -- PServer Poll Interval (printing) 
    OBJECT IDENTIFIER ::= { xcmCONetwarePServer 4 } 
    -- integerNumber (seconds, 0=immediate or 1..n) 
    -- (0=immediate - poll as frequently as application wishes) 
    -- (1..n=interval in seconds - SHOULD NOT be less than 3 seconds) 
    -- (max_int=poll once every 68 years - ie, disable polling) 
xcmCONetwarePServerFindFServer  -- PServer Find FServer (printing) 
    OBJECT IDENTIFIER ::= { xcmCONetwarePServer 5 } 
    -- integerTruthValue (true=enableFind, false=disableFind) 
xcmCONetwarePServerMaxFServers  -- PServer Max FServers (printing) 
    OBJECT IDENTIFIER ::= { xcmCONetwarePServer 6 } 
    -- integerNumber (1..n) 
xcmCONetwarePServerNotify       -- PServer Notify (printing) 
    OBJECT IDENTIFIER ::= { xcmCONetwarePServer 7 } 
    -- integerTruthValue (true=enableNotify, false=disableNotify) 
xcmCONetwarePServerNotifyLocale -- PServer Notify Locale (printing) 
    OBJECT IDENTIFIER ::= { xcmCONetwarePServerNotify 1 } 
    -- integerNumber (0=default, or 'xcmGenLocalizationIndex' of locale)
    -- (used to override 'xcmGenFixedLocalizationIndex' for this CPU) 
xcmCONetwarePServerMaxPrinters  -- PServer Max Printers (printing) 
    OBJECT IDENTIFIER ::= { xcmCONetwarePServer 8 } 
    -- integerNumber (1=default or 1..n) 
xcmCONetwarePServerSuspendPoll 
-- Enable/Disable of a different job polling interval when  
--   EnergyStarSuspend Mode is Enabled. 
OBJECT IDENTIFIER ::= { xcmCONetwarePServer 9 } 
-- integerTruthValue (true=enabled, false=disabled) 
xcmCONetwarePServerSuspendPollInterval 
-- Pserver Poll Interval when EnergyStarSuspend Mode AND  
--   xcmCONetwarePServerSuspendPoll arexe Enabled. Ignore if  

XCMI Working Group                File 52conftc                [Page 81]

Xerox Common Management Interface (XCMI) Standard               04/14/23

--   EnergyStarSuspend Mode OR xcmCONetwarePServerSuspendPoll 
--   are Disabled. 
OBJECT IDENTIFIER ::= { xcmCONetwarePServer 10 } 
-- integerNumber 

xcmCONetwarePServerSpool        -- PServer Spool (printing) 
    OBJECT IDENTIFIER ::= { xcmCONetwarePServer 31 } 
    -- integerEnum (1=none, 2=other, 3=disk, 4=ram) 
xcmCONetwarePServerMaxSpool     -- PServer Max Spool (printing) 
    OBJECT IDENTIFIER ::= { xcmCONetwarePServer 32 } 
    -- integerNumber (spool area size in bytes, 0..n) 
xcmCONetwarePServerJobTimeout   -- PServer Job Timeout (printing) 
    OBJECT IDENTIFIER ::= { xcmCONetwarePServer 40 } 
    -- integerNumber (seconds, 0=infinite or 1..n) 
xcmCONetwarePServerAutoSwitch   -- PServer Auto Switch (printing) 
    OBJECT IDENTIFIER ::= { xcmCONetwarePServer 41 } 
    -- integerEnum (see 'xcmCODirectPrintProtocol' below) 
xcmCONetwarePServerBinaryPS     -- PServer Binary PS (printing) 
    OBJECT IDENTIFIER ::= { xcmCONetwarePServer 42 } 
    -- integerTruthValue (true=enableBinaryPS, false=disableBinaryPS) 
    -- (interpret all PostScript jobs as binary - ignore control chars) 
    -- (PostScript per job submission protocol or 'xxxDefaultPDL' below)
xcmCONetwarePServerDefaultPDL   -- PServer Default PDL (printing) 
    OBJECT IDENTIFIER ::= { xcmCONetwarePServer 43 } 
    -- integerEnum ('XcmPrtInterpreterLangFamily' in XCMI Prt Ext TC) 
    -- (fixed PDL if 'xxxAutoSwitch' is 'none' or 'other') 
    -- (default PDL if 'xxxAutoSwitch' is 'autoSwitch') 
    -- (ignored if 'xxxAutoSwitch' is 'ps...' or 'hp...') 
    -- See: 'prtInterpreterLangFamily' in IETF Printer MIB (RFC 1759) 
    -- See: 'prtChannelDefaultPageDescLangIndex' (default PDL via value 
    --      of 'prtInterpreterIndex') in IETF Printer MIB (RFC 1759) 
xcmCONetwarePServerConfigTimeout -- PServer Configuration Timeout 
    OBJECT IDENTIFIER ::= { xcmCONetwarePServer 50 } 
    -- integerNumber (seconds, 0=infinite or 1..n) 
    -- The amount of timeout automatic Print Server configuration 
    -- is allowed to run before timing out. 

xcmCONetwareRPrinterName        -- RPrinter PServer Name (printing) 
    OBJECT IDENTIFIER ::= { xcmCONetwareRPrinter 1 } 
    -- stringLocalization 
    -- (compare with 'xcmCONetware[PServer|SAPUnit]Name') 
xcmCONetwareRPrinterNumber      -- RPrinter Printer Number (printing) 
    OBJECT IDENTIFIER ::= { xcmCONetwareRPrinter 2 } 
    -- integerNumber (1..n) 
xcmCONetwareRPrinterPollInterval -- RPrinter Poll Interval (printing) 
    OBJECT IDENTIFIER ::= { xcmCONetwareRPrinter 3 } 
    -- integerNumber (seconds, 0=immediate or 1..n) 
    -- (0=immediate - poll as frequently as application wishes) 
    -- (1..n=interval in seconds - SHOULD NOT be less than 3 seconds) 
    -- (max_int=poll once every 68 years - ie, disable polling) 
xcmCONetwareRPrinterJobTimeout  -- RPrinter Job Timeout (printing) 
    OBJECT IDENTIFIER ::= { xcmCONetwareRPrinter 40 } 
    -- integerNumber (seconds, 0=infinite or 1..n) 
xcmCONetwareRPrinterAutoSwitch  -- RPrinter Auto Switch (printing) 

XCMI Working Group                File 52conftc                [Page 82]

Xerox Common Management Interface (XCMI) Standard               04/14/23

    OBJECT IDENTIFIER ::= { xcmCONetwareRPrinter 41 } 
    -- integerEnum (see 'xcmCODirectPrintProtocol' below) 
xcmCONetwareRPrinterBinaryPS    -- RPrinter Binary PS (printing) 
    OBJECT IDENTIFIER ::= { xcmCONetwareRPrinter 42 } 
    -- integerTruthValue (true=enableBinaryPS, false=disableBinaryPS) 
    -- (interpret all PostScript jobs as binary - ignore control chars) 
    -- (PostScript per job submission protocol or 'xxxDefaultPDL' below)
xcmCONetwareRPrinterDefaultPDL  -- RPrinter Default PDL (printing) 
    OBJECT IDENTIFIER ::= { xcmCONetwareRPrinter 43 } 
    -- integerEnum ('XcmPrtInterpreterLangFamily' in XCMI Prt Ext TC) 
    -- (fixed PDL if 'xxxAutoSwitch' is 'none' or 'other') 
    -- (default PDL if 'xxxAutoSwitch' is 'autoSwitch') 
    -- (ignored if 'xxxAutoSwitch' is 'ps...' or 'hp...') 
    -- See: 'prtInterpreterLangFamily' in IETF Printer MIB (RFC 1759) 
    -- See: 'prtChannelDefaultPageDescLangIndex' (default PDL via value 
    --      of 'prtInterpreterIndex') in IETF Printer MIB (RFC 1759) 

xcmCONetwareFServerName         -- FServer Name (filing) 
    OBJECT IDENTIFIER ::= { xcmCONetwareFServer 1 } 
    -- stringLocalization 
xcmCONetwareFServerPassword     -- FServer Password (filing) 
    OBJECT IDENTIFIER ::= { xcmCONetwareFServer 2 } 
    -- stringLocalization (SHALL be encrypted) 
xcmCONetwareFServerAddress      -- FServer Address (filing) 
    OBJECT IDENTIFIER ::= { xcmCONetwareFServer 3 } 
    -- stringLocalization (dotted hex format, 'network.node') 

xcmCONetwareBinderyLanguage     -- Bindery Language (directory) 
    OBJECT IDENTIFIER ::= { xcmCONetwareBindery 3 } 
    -- stringLocalization (language tag, per RFC 2277) 
    -- (default is unknown language, per RFC 2277) 
xcmCONetwareBinderyCharset      -- Bindery Charset (directory) 
    OBJECT IDENTIFIER ::= { xcmCONetwareBindery 4 } 
    -- integerEnum (see 'CodedCharSet' in IETF Printer MIB) 
    -- (default '106' UTF-8, per NetWare Bindery, RFC 2277, RFC 2279) 

xcmCONetwareNDSTreeName         -- NDS Tree Name (directory) 
    OBJECT IDENTIFIER ::= { xcmCONetwareNDS 1 } 
    -- stringLocalization 
xcmCONetwareNDSContext          -- NDS Context (directory) 
    OBJECT IDENTIFIER ::= { xcmCONetwareNDS 2 } 
    -- stringLocalization 
xcmCONetwareNDSLanguage         -- NDS Language (directory) 
    OBJECT IDENTIFIER ::= { xcmCONetwareNDS 3 } 
    -- stringLocalization (language tag, per RFC 2277) 
    -- (default is unknown language, per RFC 2277) 
xcmCONetwareNDSCharset          -- NDS Charset (directory) 
    OBJECT IDENTIFIER ::= { xcmCONetwareNDS 4 } 
    -- integerEnum (see 'CodedCharSet' in IETF Printer MIB) 
    -- (default '106' UTF-8, per NetWare NDS, RFC 2277, RFC 2279) 

xcmCONetwareSAPInterval         -- SAP Interval (discovery) 
    OBJECT IDENTIFIER ::= { xcmCONetwareSAP 1 } 
    -- integerNumber (seconds, 0=none, or 1..n) 

XCMI Working Group                File 52conftc                [Page 83]

Xerox Common Management Interface (XCMI) Standard               04/14/23

xcmCONetwareSAPNumber           -- SAP Number (discovery) 
    OBJECT IDENTIFIER ::= { xcmCONetwareSAP 2 } 
    -- integerNumber (CAUTION - Novell assigned - 0=none, or 1..n) 
    -- (used with any format, including legacy ones) 
xcmCONetwareSAPValueString      -- SAP Value String (discovery) 
    OBJECT IDENTIFIER ::= { xcmCONetwareSAP 3 } 
    -- stringLocalization 
    -- (used with any format, including legacy ones) 
xcmCONetwareSAPUnitName         -- SAP Unit Name (discovery) 
    OBJECT IDENTIFIER ::= { xcmCONetwareSAP 4 } 
    -- stringLocalization 
    -- (used with any format, including legacy ones) 
    -- (compare with 'xcmCONetware[PServer|RPrinter]Name') 
xcmCONetwareSAPFormatID         -- SAP Format ID (discovery) 
    OBJECT IDENTIFIER ::= { xcmCONetwareSAP 5 } 
    -- stringLocalization 
    -- (used ONLY with XC and FX XCMI/FXCMI standard formats) 
xcmCONetwareSAPSuspend 
-- Enable/Disable of a different SAP interval when  
-- EnergyStarSuspend Mode is Enabled. 
OBJECT IDENTIFIER ::= { xcmCONetwareSAP 6 } 
-- integerTruthValue (true=enabled, false=disabled) 
xcmCONetwareSAPSuspendInterval 
-- SAP Interval when EnergyStarSuspend Mode AND xcmCONetwareSAPSuspend 
-- are Enabled. Ignore if EnergyStarSuspend Mode OR  
-- xcmCONetwareSAPSuspend are Disabled. 
OBJECT IDENTIFIER ::= { xcmCONetwareSAP 7 } 
-- integerNumber  

-- 
--          Vines Protocol Suite 
-- 

xcmCOVinesSuite 
    OBJECT IDENTIFIER ::= { xcmCommsConfigTC 20 } 
    -- integerTruthValue 

xcmCOVinesDatalinks 
    OBJECT IDENTIFIER ::= { xcmCOVinesSuite 1200 } 
    -- integerTruthValue (w/ chain of 'xcmCOOsilan...') 

xcmCOVinesTransports 
    OBJECT IDENTIFIER ::= { xcmCOVinesSuite 1400 } 
    -- integerTruthValue 
xcmCOVinesVIP                   -- VIP (CL network) 
    OBJECT IDENTIFIER ::= { xcmCOVinesSuite 1301 } 
    -- integerTruthValue 
xcmCOVinesVICP                  -- VICP (layer management - network) 
    OBJECT IDENTIFIER ::= { xcmCOVinesSuite 1302 } 
    -- integerTruthValue 
xcmCOVinesVARP                  -- VARP (routing) 
    OBJECT IDENTIFIER ::= { xcmCOVinesSuite 1303 } 
    -- integerTruthValue 
xcmCOVinesIP                    -- IP (CL network) 

XCMI Working Group                File 52conftc                [Page 84]

Xerox Common Management Interface (XCMI) Standard               04/14/23

    OBJECT IDENTIFIER ::= { xcmCOVinesSuite 1311 } 
    -- integerTruthValue 
xcmCOVinesICMP                  -- ICMP (layer management - network) 
    OBJECT IDENTIFIER ::= { xcmCOVinesSuite 1312 } 
    -- integerTruthValue 
xcmCOVinesARP                   -- ARP (routing) 
    OBJECT IDENTIFIER ::= { xcmCOVinesSuite 1313 } 
    -- integerTruthValue 
xcmCOVinesVRTP                  -- VRTP (routing) 
    OBJECT IDENTIFIER ::= { xcmCOVinesSuite 1314 } 
    -- integerTruthValue 
xcmCOVinesVIPC                  -- VIPC (CL transport) 
    OBJECT IDENTIFIER ::= { xcmCOVinesSuite 1401 } 
    -- integerTruthValue 
xcmCOVinesVSPP                  -- VSPP (CO transport) 
    OBJECT IDENTIFIER ::= { xcmCOVinesSuite 1402 } 
    -- integerTruthValue 
xcmCOVinesUDP                   -- UDP (CL transport) 
    OBJECT IDENTIFIER ::= { xcmCOVinesSuite 1411 } 
    -- integerTruthValue 
xcmCOVinesTCP                   -- TCP (CO transport) 
    OBJECT IDENTIFIER ::= { xcmCOVinesSuite 1412 } 
    -- integerTruthValue 

xcmCOVinesApplications 
    OBJECT IDENTIFIER ::= { xcmCOVinesSuite 1700 } 
    -- integerTruthValue 
xcmCOVinesNetRPC                -- NetRPC (transactions) 
    OBJECT IDENTIFIER ::= { xcmCOVinesSuite 1501 } 
    -- integerTruthValue 
xcmCOVinesSocket                -- Socket (CL/CO session) 
    OBJECT IDENTIFIER ::= { xcmCOVinesSuite 1502 } 
    -- integerTruthValue 
xcmCOVinesNetbios               -- NetBIOS (emulation) 
    OBJECT IDENTIFIER ::= { xcmCOVinesSuite 1503 } 
    -- integerTruthValue 
xcmCOVinesPrint                 -- Print (printing) 
    OBJECT IDENTIFIER ::= { xcmCOVinesSuite 1701 } 
    -- integerTruthValue 
xcmCOVinesFiling                -- Filing (filing) 
    OBJECT IDENTIFIER ::= { xcmCOVinesSuite 1702 } 
    -- integerTruthValue 
xcmCOVinesMail                  -- Mail (email) 
    OBJECT IDENTIFIER ::= { xcmCOVinesSuite 1703 } 
    -- integerTruthValue 
xcmCOVinesStreetTalk            -- StreetTalk (directory) 
    OBJECT IDENTIFIER ::= { xcmCOVinesSuite 1704 } 
    -- integerTruthValue 

xcmCOVinesPrintName             -- Print Name to Server (printing) 
    OBJECT IDENTIFIER ::= { xcmCOVinesPrint 1 } 
    -- stringLocalization 
xcmCOVinesPrintPassword         -- Print Password to Server (printing) 
    OBJECT IDENTIFIER ::= { xcmCOVinesPrint 2 } 

XCMI Working Group                File 52conftc                [Page 85]

Xerox Common Management Interface (XCMI) Standard               04/14/23

    -- stringLocalization (SHALL be encrypted) 
xcmCOVinesPrintPollInterval     -- Print Poll Interval (printing) 
    OBJECT IDENTIFIER ::= { xcmCOVinesPrint 4 } 
    -- integerNumber (seconds, 0=immediate or 1..n) 
    -- (0=immediate - poll as frequently as application wishes) 
    -- (1..n=interval in seconds - SHOULD NOT be less than 3 seconds) 
    -- (max_int=poll once every 68 years - ie, disable polling) 
xcmCOVinesPrintMaxServers       -- Print Max Servers (printing) 
    OBJECT IDENTIFIER ::= { xcmCOVinesPrint 5 } 
    -- integerNumber (0=infinite, or 1..n) 
xcmCOVinesPrintServerName       -- Print Server Name (printing) 
    OBJECT IDENTIFIER ::= { xcmCOVinesPrint 6 } 
    -- stringLocalization 
xcmCOVinesPrintSpool            -- Print Spool (printing) 
    OBJECT IDENTIFIER ::= { xcmCOVinesPrint 31 } 
    -- integerEnum (1=none, 2=other, 3=disk, 4=ram) 
xcmCOVinesPrintMaxSpool         -- Print Max Spool (printing) 
    OBJECT IDENTIFIER ::= { xcmCOVinesPrint 32 } 
    -- integerNumber (spool area size in bytes, 0..n) 
xcmCOVinesPrintJobTimeout       -- Print Job Timeout (printing) 
    OBJECT IDENTIFIER ::= { xcmCOVinesPrint 40 } 
    -- integerNumber (seconds, 0=infinite or 1..n) 
xcmCOVinesPrintAutoSwitch       -- Print Auto Switch (printing) 
    OBJECT IDENTIFIER ::= { xcmCOVinesPrint 41 } 
    -- integerEnum (see 'xcmCODirectPrintProtocol' below) 
xcmCOVinesPrintBinaryPS         -- Print Binary PS (printing) 
    OBJECT IDENTIFIER ::= { xcmCOVinesPrint 42 } 
    -- integerTruthValue (true=enableBinaryPS, false=disableBinaryPS) 
    -- (interpret all PostScript jobs as binary - ignore control chars) 
    -- (PostScript per job submission protocol or 'xxxDefaultPDL' below)
xcmCOVinesPrintDefaultPDL       -- Print Default PDL (printing) 
    OBJECT IDENTIFIER ::= { xcmCOVinesPrint 43 } 
    -- integerEnum ('XcmPrtInterpreterLangFamily' in XCMI Prt Ext TC) 
    -- (fixed PDL if 'xxxAutoSwitch' is 'none' or 'other') 
    -- (default PDL if 'xxxAutoSwitch' is 'autoSwitch') 
    -- (ignored if 'xxxAutoSwitch' is 'ps...' or 'hp...') 
    -- See: 'prtInterpreterLangFamily' in IETF Printer MIB (RFC 1759) 
    -- See: 'prtChannelDefaultPageDescLangIndex' (default PDL via value 
    --      of 'prtInterpreterIndex') in IETF Printer MIB (RFC 1759) 

xcmCOVinesStreetTalkLanguage    -- StreetTalk Language (directory) 
    OBJECT IDENTIFIER ::= { xcmCOVinesStreetTalk 3 } 
    -- stringLocalization (language tag, per RFC 2277) 
    -- (default is unknown language, per RFC 2277) 
xcmCOVinesStreetTalkCharset     -- StreetTalk Charset (directory) 
    OBJECT IDENTIFIER ::= { xcmCOVinesStreetTalk 4 } 
    -- integerEnum (see 'CodedCharSet' in IETF Printer MIB) 
    -- (default '106' UTF-8, per Vines StreetTalk, RFC 2277, RFC 2279) 







XCMI Working Group                File 52conftc                [Page 86]

Xerox Common Management Interface (XCMI) Standard               04/14/23

-- 
--          NetBIOS Protocol Suite 
-- 

xcmCONetbiosSuite 
    OBJECT IDENTIFIER ::= { xcmCommsConfigTC 25 } 
    -- integerTruthValue 

xcmCONetbiosDatalinks 
    OBJECT IDENTIFIER ::= { xcmCONetbiosSuite 1200 } 
    -- integerTruthValue (w/ chain of 'xcmCOOsilan...') 

xcmCONetbiosTransports 
    OBJECT IDENTIFIER ::= { xcmCONetbiosSuite 1400 } 
    -- integerTruthValue 

xcmCONetbiosNBP                 -- NBP (NetBIOS Protocol) 
    OBJECT IDENTIFIER ::= { xcmCONetbiosSuite 1501 } 
    -- integerTruthValue 


xcmCONetbiosSNMP                -- SNMP (network mgmt) 
    OBJECT IDENTIFIER ::= { xcmCONetbiosSuite 1510 } 
    -- integerTruthValue 
xcmCONetbiosSNMPv1              -- SNMPv1 (network mgmt) 
    OBJECT IDENTIFIER ::= { xcmCONetbiosSuite 1511 } 
    -- integerTruthValue 
xcmCONetbiosSNMPv2              -- SNMPv2 (network mgmt) 
    OBJECT IDENTIFIER ::= { xcmCONetbiosSuite 1512 } 
    -- integerTruthValue 
xcmCONetbiosSNMPv3              -- SNMPv3 (network mgmt) 
    OBJECT IDENTIFIER ::= { xcmCONetbiosSuite 1513 } 
    -- integerTruthValue 

xcmCONetbiosIntEndNode           -- NetBIOS over TCP End Node 
    OBJECT IDENTIFIER ::= { xcmCONetbiosSuite 1520 } 
    -- integerTruthValue 
    -- See: RFC 1001/1002 (NetBIOS over TCP) and RFC 2132 (DHCP Options)
xcmCONetbiosIntNameServer        -- NetBIOS over TCP Name Server 
    OBJECT IDENTIFIER ::= { xcmCONetbiosSuite 1521 } 
    -- integerTruthValue 
    -- See: RFC 1001/1002 (NetBIOS over TCP) and RFC 2132 (DHCP Options)
xcmCONetbiosIntDistServer        -- NetBIOS over TCP Dist Server 
    OBJECT IDENTIFIER ::= { xcmCONetbiosSuite 1522 } 
    -- integerTruthValue 
    -- See: RFC 1001/1002 (NetBIOS over TCP) and RFC 2132 (DHCP Options)

xcmCONetbiosSAP                 -- SAP (discovery) 
    OBJECT IDENTIFIER ::= { xcmCONetbiosSuite 1591 } 
    -- integerTruthValue 

xcmCONetbiosApplications 
    OBJECT IDENTIFIER ::= { xcmCONetbiosSuite 1700 } 
    -- integerTruthValue 

XCMI Working Group                File 52conftc                [Page 87]

Xerox Common Management Interface (XCMI) Standard               04/14/23

xcmCONetbiosSMB                 -- SMB (Server Message Block) 
    OBJECT IDENTIFIER ::= { xcmCONetbiosSuite 1701 } 
    -- integerTruthValue 
xcmCONetbiosSMBPClient          -- SMB Printing Client 
    OBJECT IDENTIFIER ::= { xcmCONetbiosSuite 1702 } 
    -- integerTruthValue 
xcmCONetbiosSMBPServer          -- SMB Printing Server 
    OBJECT IDENTIFIER ::= { xcmCONetbiosSuite 1703 } 
    -- integerTruthValue 
xcmCONetbiosSMBFClient          -- SMB Filing Client 
    OBJECT IDENTIFIER ::= { xcmCONetbiosSuite 1704 } 
    -- integerTruthValue 
xcmCONetbiosSMBFServer          -- SMB Filing Server 
    OBJECT IDENTIFIER ::= { xcmCONetbiosSuite 1705 } 
    -- integerTruthValue 
xcmCONetbiosSMBDomain          -- SMB Domain 
    OBJECT IDENTIFIER ::= { xcmCONetbiosSuite 1706 } 
xcmCONetbiosSMBv1          -- SMBv1 Enable/Disable 
    OBJECT IDENTIFIER ::= { xcmCONetbiosSuite 1707 } 
    -- integerTruthValue 
xcmCONetbiosSMBv2          -- SMBv2 Enable/Disable 
    OBJECT IDENTIFIER ::= { xcmCONetbiosSuite 1708 } 
    -- integerTruthValue 
xcmCONetbiosSMBv3          -- SMBv3 Enable/Disable 
    OBJECT IDENTIFIER ::= { xcmCONetbiosSuite 1709 } 
    -- integerTruthValue 
xcmCONetbiosSMBv3Dialect   -- SMBv3 Dialect 
    OBJECT IDENTIFIER ::= { xcmCONetbiosSMBv3 1 } 
    -- integerEnum (1-SMBv3 dialect v3.00,  
 -- 2-SMBv3 maximum dialect v3.02, 
 -- 3-SMBv3 maximum dialect v3.11) 

xcmCONetbiosNBPName             -- NBP Name (directory) 
    OBJECT IDENTIFIER ::= { xcmCONetbiosNBP 1 } 
    -- often used for 'SMB Host Name' value 
    -- stringLocalization (hostname) 
xcmCONetbiosNBPGroupName        -- NBP Group Name (directory) 
    OBJECT IDENTIFIER ::= { xcmCONetbiosNBP 2 } 
    -- often used for 'Workgroup' value 
    -- stringLocalization (groupname) 
xcmCONetbiosNBPPassword         -- NBP Password (directory) 
    OBJECT IDENTIFIER ::= { xcmCONetbiosNBP 3 } 
    -- stringLocalization (SHALL be encrypted) 
xcmCONetbiosNBPService          -- NBP Service (directory) 
    OBJECT IDENTIFIER ::= { xcmCONetbiosNBP 4 } 
    -- often used for 'Share Name' value 
    -- stringLocalization (servicename) 
xcmCONetbiosNBPRemark           -- NBP Node Remark (directory) 
    OBJECT IDENTIFIER ::= { xcmCONetbiosNBP 5 } 
    -- often used for 'SMB Host Name Comment' value 
    -- stringLocalization (hostname comment) 
xcmCONetbiosNBPServiceRemark    -- NBP Service Remark (directory) 
    OBJECT IDENTIFIER ::= { xcmCONetbiosNBP 6 } 
    -- often used for 'Share Name Comment' value 

XCMI Working Group                File 52conftc                [Page 88]

Xerox Common Management Interface (XCMI) Standard               04/14/23

    -- stringLocalization (sharename comment) 
xcmCONetbiosNBPIPCRemark        -- NBP IPC Remark (directory) 
    OBJECT IDENTIFIER ::= { xcmCONetbiosNBP 7 } 
    -- stringLocalization (IPC$ comment - transport, address, type) 
xcmCONetbiosNBPLanguage         -- NetBIOS Language (directory) 
    OBJECT IDENTIFIER ::= { xcmCONetbiosNBP 8 } 
    -- stringLocalization (language tag, per RFC 2277) 
    -- (default is unknown language, per RFC 2277) 
xcmCONetbiosNBPCharset          -- NetBIOS Charset (directory) 
    OBJECT IDENTIFIER ::= { xcmCONetbiosNBP 9 } 
    -- integerEnum (see 'CodedCharSet' in IETF Printer MIB) 
    -- (default '106' UTF-8, per RFC 2277, RFC 2279) 
xcmCONetbiosNBPOverNetbeui      -- NetBIOS over NetBEUI (native) 
    OBJECT IDENTIFIER ::= { xcmCONetbiosNBP 11 } 
    -- integerTruthValue 
xcmCONetbiosNBPOverInternet     -- NetBIOS over TCP (RFC 1001/1002) 
    OBJECT IDENTIFIER ::= { xcmCONetbiosNBP 12 } 
    -- integerTruthValue 
xcmCONetbiosNBPOverNetware      -- NetBIOS over IPX (Netware) 
    OBJECT IDENTIFIER ::= { xcmCONetbiosNBP 13 } 
    -- integerTruthValue 

xcmCONetbiosIntEndNodeAddress    -- NetBIOS over TCP End Node Address 
    OBJECT IDENTIFIER ::= { xcmCONetbiosIntEndNode 1 } 
    -- stringLocalization (dotted decimal format, 'a.b.c.d') 
    -- ('a' to 'd' [1-3 octets] - ASCII decimal of 1-octet components) 
    -- See: RFC 1001/1002 (NetBIOS over TCP) and RFC 2132 (DHCP Options)
xcmCONetbiosIntEndNodeSource     -- NetBIOS over TCP End Node Source 
    OBJECT IDENTIFIER ::= { xcmCONetbiosIntEndNode 2 } 
    -- integerEnum (1=none, 2=other, 
    -- 3=static, 4=reserved, 5=viaBOOTP, 6=viaDHCP) 

xcmCONetbiosIntNodeType         -- NetBIOS over TCP Node Type 
    OBJECT IDENTIFIER ::= { xcmCONetbiosIntEndNode 3 } 
    -- integerEnum (1=none, 2=other, 
    -- 3=broadcast, 4=pointToPoint, 5=mixedMode) 
    -- See: RFC 1001/1002 (NetBIOS over TCP) and RFC 2132 (DHCP Options)
xcmCONetbiosIntNodeTypeSource   -- NetBIOS over TCP Node Type Source 
    OBJECT IDENTIFIER ::= { xcmCONetbiosIntEndNode 4 } 
    -- integerEnum (1=none, 2=other, 
    -- 3=static, 4=reserved, 5=viaBOOTP, 6=viaDHCP) 

xcmCONetbiosIntNodeScope         -- NetBIOS over TCP Node Scope 
    OBJECT IDENTIFIER ::= { xcmCONetbiosIntEndNode 5 } 
    -- stringLocalization (must be valid DNS name) 
    -- See: RFC 1001/1002 (NetBIOS over TCP) and RFC 2132 (DHCP Options)
xcmCONetbiosIntNodeScopeSource   -- NetBIOS over TCP Node Scope Source 
    OBJECT IDENTIFIER ::= { xcmCONetbiosIntEndNode 6 } 
    -- integerEnum (1=none, 2=other, 
    -- 3=static, 4=reserved, 5=viaBOOTP, 6=viaDHCP) 

xcmCONetbiosIntNameServerAddress -- NetBIOS over TCP Name Server Address
    OBJECT IDENTIFIER ::= { xcmCONetbiosIntNameServer 1 } 
    -- stringLocalization (dotted decimal format, 'a.b.c.d') 

XCMI Working Group                File 52conftc                [Page 89]

Xerox Common Management Interface (XCMI) Standard               04/14/23

    -- ('a' to 'd' [1-3 octets] - ASCII decimal of 1-octet components) 
    -- See: RFC 1001/1002 (NetBIOS over TCP) and RFC 2132 (DHCP Options)
xcmCONetbiosIntNameServerSource  -- NetBIOS over TCP Name Server Source 
    OBJECT IDENTIFIER ::= { xcmCONetbiosIntNameServer 2 } 
    -- integerEnum (1=none, 2=other, 
    -- 3=static, 4=reserved, 5=viaBOOTP, 6=viaDHCP) 

xcmCONetbiosIntDistServerAddress -- NetBIOS over TCP Dist Server Address
    OBJECT IDENTIFIER ::= { xcmCONetbiosIntDistServer 1 } 
    -- stringLocalization (dotted decimal format, 'a.b.c.d') 
    -- ('a' to 'd' [1-3 octets] - ASCII decimal of 1-octet components) 
    -- See: RFC 1001/1002 (NetBIOS over TCP) and RFC 2132 (DHCP Options)
xcmCONetbiosIntDistServerSource  -- NetBIOS over TCP Dist Server Source 
    OBJECT IDENTIFIER ::= { xcmCONetbiosIntDistServer 2 } 
    -- integerEnum (1=none, 2=other, 
    -- 3=static, 4=reserved, 5=viaBOOTP, 6=viaDHCP) 

xcmCONetbiosSAPInterval         -- SAP Interval (discovery) 
    OBJECT IDENTIFIER ::= { xcmCONetbiosSAP 1 } 
    -- integerNumber (seconds, 0=none, or 1..n) 

xcmCONetbiosSMBPClientMaxConns  -- Print Client Max Conns (concurrently)
    OBJECT IDENTIFIER ::= { xcmCONetbiosSMBPClient 4 } 
    -- integerNumber (0..n) 
xcmCONetbiosSMBPClientSpool     -- Print Client Spool (printing) 
    OBJECT IDENTIFIER ::= { xcmCONetbiosSMBPClient 31 } 
    -- integerEnum (1=none, 2=other, 3=disk, 4=ram) 
xcmCONetbiosSMBPClientMaxSpool  -- Print Client Max Spool (printing) 
    OBJECT IDENTIFIER ::= { xcmCONetbiosSMBPClient 32 } 
    -- integerNumber (spool area size in bytes, 0..n) 
xcmCONetbiosSMBPClientJobTimeout -- Print Client Job Timeout (printing) 
    OBJECT IDENTIFIER ::= { xcmCONetbiosSMBPClient 40 } 
    -- integerNumber (seconds, 0=infinite or 1..n) 
xcmCONetbiosSMBPClientAutoSwitch -- Print Client Auto Switch (printing) 
    OBJECT IDENTIFIER ::= { xcmCONetbiosSMBPClient 41 } 
    -- integerEnum (see 'xcmCODirectPrintProtocol' below) 
xcmCONetbiosSMBPClientBinaryPS   -- Print Client Binary PS (printing) 
    OBJECT IDENTIFIER ::= { xcmCONetbiosSMBPClient 42 } 
    -- integerTruthValue (true=enableBinaryPS, false=disableBinaryPS) 
    -- (interpret all PostScript jobs as binary - ignore control chars) 
    -- (PostScript per job submission protocol or 'xxxDefaultPDL' below)
xcmCONetbiosSMBPClientDefaultPDL -- Print Client Default PDL (printing) 
    OBJECT IDENTIFIER ::= { xcmCONetbiosSMBPClient 43 } 
    -- integerEnum ('XcmPrtInterpreterLangFamily' in XCMI Prt Ext TC) 
    -- (fixed PDL if 'xxxAutoSwitch' is 'none' or 'other') 
    -- (default PDL if 'xxxAutoSwitch' is 'autoSwitch') 
    -- (ignored if 'xxxAutoSwitch' is 'ps...' or 'hp...') 
    -- See: 'prtInterpreterLangFamily' in IETF Printer MIB (RFC 1759) 
    -- See: 'prtChannelDefaultPageDescLangIndex' (default PDL via value 
    --      of 'prtInterpreterIndex') in IETF Printer MIB (RFC 1759) 

xcmCONetbiosSMBPServerMaxConns  -- Print Server Max Conns (concurrently)
    OBJECT IDENTIFIER ::= { xcmCONetbiosSMBPServer 4 } 
    -- integerNumber (0..n) 

XCMI Working Group                File 52conftc                [Page 90]

Xerox Common Management Interface (XCMI) Standard               04/14/23

xcmCONetbiosSMBPServerSpool     -- Print Server Spool (printing) 
    OBJECT IDENTIFIER ::= { xcmCONetbiosSMBPServer 31 } 
    -- integerEnum (1=none, 2=other, 3=disk, 4=ram) 
xcmCONetbiosSMBPServerMaxSpool  -- Print Server Max Spool (printing) 
    OBJECT IDENTIFIER ::= { xcmCONetbiosSMBPServer 32 } 
    -- integerNumber (spool area size in bytes, 0..n) 
xcmCONetbiosSMBPServerJobTimeout -- Print Server Job Timeout (printing) 
    OBJECT IDENTIFIER ::= { xcmCONetbiosSMBPServer 40 } 
    -- integerNumber (seconds, 0=infinite or 1..n) 
xcmCONetbiosSMBPServerAutoSwitch -- Print Server Auto Switch (printing) 
    OBJECT IDENTIFIER ::= { xcmCONetbiosSMBPServer 41 } 
    -- integerEnum (see 'xcmCODirectPrintProtocol' below) 
xcmCONetbiosSMBPServerBinaryPS   -- Print Server Binary PS (printing) 
    OBJECT IDENTIFIER ::= { xcmCONetbiosSMBPServer 42 } 
    -- integerTruthValue (true=enableBinaryPS, false=disableBinaryPS) 
    -- (interpret all PostScript jobs as binary - ignore control chars) 
    -- (PostScript per job submission protocol or 'xxxDefaultPDL' below)
xcmCONetbiosSMBPServerDefaultPDL -- Print Server Default PDL (printing) 
    OBJECT IDENTIFIER ::= { xcmCONetbiosSMBPServer 43 } 
    -- integerEnum ('XcmPrtInterpreterLangFamily' in XCMI Prt Ext TC) 
    -- (fixed PDL if 'xxxAutoSwitch' is 'none' or 'other') 
    -- (default PDL if 'xxxAutoSwitch' is 'autoSwitch') 
    -- (ignored if 'xxxAutoSwitch' is 'ps...' or 'hp...') 
    -- See: 'prtInterpreterLangFamily' in IETF Printer MIB (RFC 1759) 
    -- See: 'prtChannelDefaultPageDescLangIndex' (default PDL via value 
    --      of 'prtInterpreterIndex') in IETF Printer MIB (RFC 1759) 

xcmCONetbiosSMBFServerName      -- SMB Filing Server Name 
    OBJECT IDENTIFIER ::= { xcmCONetbiosSMBFServer 1 } 
    -- stringLocalization 

-- 
--          NetBEUI Protocol Suite 
-- 

xcmCONetbeuiSuite 
    OBJECT IDENTIFIER ::= { xcmCommsConfigTC 26 } 
    -- integerTruthValue 

xcmCONetbeuiDatalinks 
    OBJECT IDENTIFIER ::= { xcmCONetbeuiSuite 1200 } 
    -- integerTruthValue (w/ chain of 'xcmCOOsilan...') 
xcmCONetbeuiLLC                 -- NetBEUI LLC (ISO/IEEE 802.2) 
    OBJECT IDENTIFIER ::= { xcmCONetbeuiSuite 1201 } 
    -- integerTruthValue 
xcmCONetbeuiDLC                 -- NetBEUI DLC (IBM SNA DLC) 
    OBJECT IDENTIFIER ::= { xcmCONetbeuiSuite 1202 } 
    -- integerTruthValue 







XCMI Working Group                File 52conftc                [Page 91]

Xerox Common Management Interface (XCMI) Standard               04/14/23

-- 
--          Serial Protocol Suite 
-- 

xcmCOSerialSuite 
    OBJECT IDENTIFIER ::= { xcmCommsConfigTC 27 } 
    -- integerTruthValue 

xcmCOSerialPhysical 
    OBJECT IDENTIFIER ::= { xcmCOSerialSuite 1100 } 
    -- integerTruthValue 
xcmCOSerialSignalType 
    OBJECT IDENTIFIER ::= { xcmCOSerialSuite 1101 } 
    -- integerEnum (1=none, 2=other, 3=rs232, 4=rs422, 5=v35) 
xcmCOSerialSignalOverride       -- Serial Signal Type Override 
    OBJECT IDENTIFIER ::= { xcmCOSerialSignalType 1 } 
    -- integerEnum (see 'xcmCOSerialSignalType' above) 
xcmCOSerialSignalDetected       -- Serial Signal Type Detected 
    OBJECT IDENTIFIER ::= { xcmCOSerialSignalType 2 } 
    -- integerEnum (see 'xcmCOSerialSignalType' above) 
xcmCOSerialSignalAdaptive       -- Serial Signal Type Adaptive 
    OBJECT IDENTIFIER ::= { xcmCOSerialSignalType 3 } 
    -- integerTruthValue 
xcmCOSerialSignalSupport        -- OSI LAN Signal Type Support 
    OBJECT IDENTIFIER ::= { xcmCOSerialSignalType 4 } 
    -- integerEnum (list of 'xcmCOSerialSignalType' above) 
xcmCOSerialDevice 
    OBJECT IDENTIFIER ::= { xcmCOSerialSuite 1102 } 
    -- integerNumber ('hrDeviceIndex' in IETF HR MIB, or 0=unknown) 
xcmCOSerialDeviceName 
    OBJECT IDENTIFIER ::= { xcmCOSerialDevice 1 } 
    -- stringLocalization ('xcmHrDevInfoName' in HRX, eg, '/dev/com1') 
xcmCOSerialSpeed 
    OBJECT IDENTIFIER ::= { xcmCOSerialSuite 1103 } 
    -- integerNumber (as in 'ifSpeed' in IETF MIB-II) 
xcmCOSerialSpeedOverride 
    OBJECT IDENTIFIER ::= { xcmCOSerialSpeed 1 } 
    -- integerNumber (see 'xcmCOSerialSpeed' above) 
xcmCOSerialSpeedDetected 
    OBJECT IDENTIFIER ::= { xcmCOSerialSpeed 2 } 
    -- integerNumber (see 'xcmCOSerialSpeed' above) 
xcmCOSerialSpeedAdaptive 
    OBJECT IDENTIFIER ::= { xcmCOSerialSpeed 3 } 
    -- integerTruthValue 
xcmCOSerialSpeedSupport 
    OBJECT IDENTIFIER ::= { xcmCOSerialSpeed 4 } 
    -- integerNumber (as in 'ifSpeed' in IETF MIB-II, list of speeds) 
xcmCOSerialMinSpeed 
    OBJECT IDENTIFIER ::= { xcmCOSerialSpeed 5 } 
    -- integerNumber (as in 'ifSpeed' in IETF MIB-II) 
xcmCOSerialMaxSpeed 
    OBJECT IDENTIFIER ::= { xcmCOSerialSpeed 6 } 
    -- integerNumber (as in 'ifSpeed' in IETF MIB-II) 
xcmCOSerialBidirectional 

XCMI Working Group                File 52conftc                [Page 92]

Xerox Common Management Interface (XCMI) Standard               04/14/23

    OBJECT IDENTIFIER ::= { xcmCOSerialSuite 1104 } 
    -- integerTruthValue 
xcmCOSerialInputTimeout         -- POSIX.1 'VTIME' * 10 (in 'termios.h')
    OBJECT IDENTIFIER ::= { xcmCOSerialSuite 1105 } 
    -- integerNumber (seconds, 0=infinite or 1..n) 
xcmCOSerialOutputTimeout 
    OBJECT IDENTIFIER ::= { xcmCOSerialSuite 1106 } 
    -- integerNumber (seconds, 0=infinite or 1..n) 
xcmCOSerialConnectorType 
    OBJECT IDENTIFIER ::= { xcmCOSerialSuite 1107 } 
    -- integerEnum (1=none, 2=other, 3=db9, 4=db25, 5=v35, 6=rj11) 
xcmCOSerialConnectorOverride    -- Serial Connector Type Override 
    OBJECT IDENTIFIER ::= { xcmCOSerialConnectorType 1 } 
    -- integerEnum (see 'xcmCOSerialConnectorType' above) 
xcmCOSerialConnectorDetected    -- Serial Connector Type Detected 
    OBJECT IDENTIFIER ::= { xcmCOSerialConnectorType 2 } 
    -- integerEnum (see 'xcmCOSerialConnectorType' above) 
xcmCOSerialConnectorAdaptive    -- Serial Connector Type Adaptive 
    OBJECT IDENTIFIER ::= { xcmCOSerialConnectorType 3 } 
    -- integerTruthValue 
xcmCOSerialMinInputChars        -- POSIX.1 'VMIN' (in 'termios.h') 
    OBJECT IDENTIFIER ::= { xcmCOSerialSuite 1108 } 
    -- integerNumber (0=infinite or 1..n) 
xcmCOSerialMaxInputChars        -- POSIX.1 'nbyte' (in 'read()') 
    OBJECT IDENTIFIER ::= { xcmCOSerialSuite 1109 } 
    -- integerNumber (0=infinite or 1..n) 
xcmCOSerialParity 
    OBJECT IDENTIFIER ::= { xcmCOSerialSuite 1111 } 
    -- integerEnum (1=none, 2=odd, 3=even, 4=mark, 5=space) 
xcmCOSerialDataBits 
    OBJECT IDENTIFIER ::= { xcmCOSerialSuite 1112 } 
    -- integerNumber (0=default or 5..8) 
xcmCOSerialFlowControl 
    OBJECT IDENTIFIER ::= { xcmCOSerialSuite 1113 } 
    -- integerEnum (1=none, 2=xonXoff, 3=rtsCts, 4=dtrDsr, 
    -- 5=robustXonXoff) 
xcmCOSerialStartBits 
    OBJECT IDENTIFIER ::= { xcmCOSerialSuite 1114 } 
    -- integerEnum (0=default or 1=1 bit, 2=1.5 bits) 
xcmCOSerialStopBits 
    OBJECT IDENTIFIER ::= { xcmCOSerialSuite 1115 } 
    -- integerEnum (0=default or 1=1 bit, 2=2 bits, 3=1.5 bits) 
xcmCOSerialInputPrime 
    OBJECT IDENTIFIER ::= { xcmCOSerialSuite 1116 } 
    -- integerTruthValue 
xcmCOSerialDTR                  -- Data Terminal Ready 
    OBJECT IDENTIFIER ::= { xcmCOSerialSuite 1121 } 
    -- integerEnum (1=fixedHigh, 2=fixedLow, 3=activeHigh, 4=activeLow) 
xcmCOSerialDSR                  -- Data Set Ready 
    OBJECT IDENTIFIER ::= { xcmCOSerialSuite 1122 } 
    -- integerEnum (1=fixedHigh, 2=fixedLow, 3=activeHigh, 4=activeLow) 
xcmCOSerialCTS                  -- Clear To Send 
    OBJECT IDENTIFIER ::= { xcmCOSerialSuite 1123 } 
    -- integerEnum (1=fixedHigh, 2=fixedLow, 3=activeHigh, 4=activeLow) 

XCMI Working Group                File 52conftc                [Page 93]

Xerox Common Management Interface (XCMI) Standard               04/14/23

xcmCOSerialRTS                  -- Request To Send 
    OBJECT IDENTIFIER ::= { xcmCOSerialSuite 1124 } 
    -- integerEnum (1=fixedHigh, 2=fixedLow, 3=activeHigh, 4=activeLow) 

xcmCOSerialDatalinks 
    OBJECT IDENTIFIER ::= { xcmCOSerialSuite 1200 } 
    -- integerTruthValue 

xcmCOSerialProtocol 
    OBJECT IDENTIFIER ::= { xcmCOSerialDatalinks 1 } 
    -- integerEnum (see 'xcmCODirectPrintProtocol' below) 

-- 
--          Parallel Protocol Suite 
-- 

xcmCOParallelSuite 
    OBJECT IDENTIFIER ::= { xcmCommsConfigTC 28 } 
    -- integerTruthValue 

xcmCOParallelPhysical 
    OBJECT IDENTIFIER ::= { xcmCOParallelSuite 1100 } 
    -- integerTruthValue 
xcmCOParallelSignalType 
    OBJECT IDENTIFIER ::= { xcmCOParallelSuite 1101 } 
    -- integerEnum (1=none, 2=other, 3=centronics, 4=ecp, 5=epp) 
xcmCOParallelSignalOverride     -- Parallel Signal Type Override 
    OBJECT IDENTIFIER ::= { xcmCOParallelSignalType 1 } 
    -- integerEnum (see 'xcmCOParallelSignalType' above) 
xcmCOParallelSignalDetected     -- Parallel Signal Type Detected 
    OBJECT IDENTIFIER ::= { xcmCOParallelSignalType 2 } 
    -- integerEnum (see 'xcmCOParallelSignalType' above) 
xcmCOParallelSignalAdaptive     -- Parallel Signal Type Adaptive 
    OBJECT IDENTIFIER ::= { xcmCOParallelSignalType 3 } 
    -- integerTruthValue 
xcmCOParallelSignalSupport      -- OSI LAN Signal Type Support 
    OBJECT IDENTIFIER ::= { xcmCOParallelSignalType 4 } 
    -- integerEnum (list of 'xcmCOParallelSignalType' above) 
xcmCOParallelDevice 
    OBJECT IDENTIFIER ::= { xcmCOParallelSuite 1102 } 
    -- integerNumber ('hrDeviceIndex' in IETF HR MIB, or 0=unknown) 
xcmCOParallelDeviceName 
    OBJECT IDENTIFIER ::= { xcmCOParallelDevice 1 } 
    -- stringLocalization ('xcmHrDevInfoName' in HRX, eg, '/dev/lpr1') 
xcmCOParallelDeviceID           -- IEEE 1284 Device Identifier 
    OBJECT IDENTIFIER ::= { xcmCOParallelDevice 2 } 
    -- stringLocalization (set of capabilities as 'key:value(,value)') 
    -- (keys and values MUST be US-ASCII) 
    -- (spaces, tabs, formfeeds and line breaks are allowed and ignored)
    -- (values are delimited by a comma) 
    -- (capabilites are delimited by a semicolon) 
    -- (REQUIRED capabilities for all systems are: 
    -- - MANUFACTURER (or abbreviation MFG) 
    -- - COMMAND SET (or abbreviation CMD) 

XCMI Working Group                File 52conftc                [Page 94]

Xerox Common Management Interface (XCMI) Standard               04/14/23

    -- - MODEL (or abbreviation MDL) 
    -- (OPTIONAL capabilities for all systems include: 
    -- - COMMENT 
    -- - ACTIVE COMMAND SET 
    -- (eg, 'MANUFACTURER: Xerox; COMMAND SET:PCL, PJL, PS; MODEL: ...')
    -- (see section 7.6 of IEEE 1284-2000) 
xcmCOParallelSpeed 
    OBJECT IDENTIFIER ::= { xcmCOParallelSuite 1103 } 
    -- integerNumber (as in 'ifSpeed' in IETF MIB-II) 
xcmCOParallelSpeedOverride 
    OBJECT IDENTIFIER ::= { xcmCOParallelSpeed 1 } 
    -- integerNumber (see 'xcmCOParallelSpeed' above) 
xcmCOParallelSpeedDetected 
    OBJECT IDENTIFIER ::= { xcmCOParallelSpeed 2 } 
    -- integerNumber (see 'xcmCOParallelSpeed' above) 
xcmCOParallelSpeedAdaptive 
    OBJECT IDENTIFIER ::= { xcmCOParallelSpeed 3 } 
    -- integerTruthValue 
xcmCOParallelSpeedSupport 
    OBJECT IDENTIFIER ::= { xcmCOParallelSpeed 4 } 
    -- integerNumber (as in 'ifSpeed' in IETF MIB-II, list of speeds) 
xcmCOParallelMinSpeed 
    OBJECT IDENTIFIER ::= { xcmCOParallelSpeed 5 } 
    -- integerNumber (as in 'ifSpeed' in IETF MIB-II) 
xcmCOParallelMaxSpeed 
    OBJECT IDENTIFIER ::= { xcmCOParallelSpeed 6 } 
    -- integerNumber (as in 'ifSpeed' in IETF MIB-II) 
xcmCOParallelBidirectional 
    OBJECT IDENTIFIER ::= { xcmCOParallelSuite 1104 } 
    -- integerTruthValue 
xcmCOParallelInputTimeout       -- POSIX.1 'VTIME' * 10 (in 'termios.h')
    OBJECT IDENTIFIER ::= { xcmCOParallelSuite 1105 } 
    -- integerNumber (seconds, 0=infinite or 1..n) 
xcmCOParallelOutputTimeout 
    OBJECT IDENTIFIER ::= { xcmCOParallelSuite 1106 } 
    -- integerNumber (seconds, 0=infinite or 1..n) 
xcmCOParallelConnectorType 
    OBJECT IDENTIFIER ::= { xcmCOParallelSuite 1107 } 
    -- integerEnum (1=none, 2=other, 3=centronics, 4=db25) 
xcmCOParallelConnectorOverride  -- Parallel Connector Type Override 
    OBJECT IDENTIFIER ::= { xcmCOParallelConnectorType 1 } 
    -- integerEnum (see 'xcmCOParallelConnectorType' above) 
xcmCOParallelConnectorDetected  -- Parallel Connector Type Detected 
    OBJECT IDENTIFIER ::= { xcmCOParallelConnectorType 2 } 
    -- integerEnum (see 'xcmCOParallelConnectorType' above) 
xcmCOParallelConnectorAdaptive  -- Parallel Connector Type Adaptive 
    OBJECT IDENTIFIER ::= { xcmCOParallelConnectorType 3 } 
    -- integerTruthValue 
xcmCOParallelMinInputChars      -- POSIX.1 'VMIN' (in 'termios.h') 
    OBJECT IDENTIFIER ::= { xcmCOParallelSuite 1108 } 
    -- integerNumber (0=infinite or 1..n) 
xcmCOParallelMaxInputChars      -- POSIX.1 'nbyte' (in 'read()') 
    OBJECT IDENTIFIER ::= { xcmCOParallelSuite 1109 } 
    -- integerNumber (0=infinite or 1..n) 

XCMI Working Group                File 52conftc                [Page 95]

Xerox Common Management Interface (XCMI) Standard               04/14/23

xcmCOParallelParity 
    OBJECT IDENTIFIER ::= { xcmCOParallelSuite 1111 } 
    -- integerEnum (1=none, 2=odd, 3=even, 4=mark, 5=space) 
xcmCOParallelDataBits 
    OBJECT IDENTIFIER ::= { xcmCOParallelSuite 1112 } 
    -- integerNumber (0=default or 7..8) 
xcmCOParallelFlowControl 
    OBJECT IDENTIFIER ::= { xcmCOParallelSuite 1113 } 
    -- integerEnum (1=none, 2=xonXoff) 
xcmCOParallelInputPrime 
    OBJECT IDENTIFIER ::= { xcmCOParallelSuite 1116 } 
    -- integerTruthValue 
xcmCOParallelHandshake 
    OBJECT IDENTIFIER ::= { xcmCOParallelSuite 1117 } 
    -- integerEnum (1=none, 2=ackBusy, 3=ackBusyAck, 4=busyAck) 
xcmCOParallelDataStrobe 
    OBJECT IDENTIFIER ::= { xcmCOParallelSuite 1118 } 
    -- integerNumber (microseconds, 0=none, or 1..n) 

xcmCOParallelDatalinks 
    OBJECT IDENTIFIER ::= { xcmCOParallelSuite 1200 } 
    -- integerTruthValue 

xcmCOParallelProtocol 
    OBJECT IDENTIFIER ::= { xcmCOParallelDatalinks 1 } 
    -- integerEnum (see 'xcmCODirectPrintProtocol' below) 

-- 
--          Direct Print Protocol Suite (Serial/Parallel) 
-- 

xcmCODirectPrintSuite 
    OBJECT IDENTIFIER ::= { xcmCommsConfigTC 29 } 
    -- integerTruthValue 

xcmCODirectPrintPhysical 
    OBJECT IDENTIFIER ::= { xcmCODirectPrintSuite 1100 } 
    -- integerTruthValue 

xcmCODirectPrintDatalinks 
    OBJECT IDENTIFIER ::= { xcmCODirectPrintSuite 1200 } 
    -- integerTruthValue 

xcmCODirectPrintProtocol 
    OBJECT IDENTIFIER ::= { xcmCODirectPrintDatalinks 1 } 
    -- integerEnum 
    -- Generic datastream encoding and interpreter modes 
    -- See: Vendor datastream encoding and interpreter language specs 
    -- (1=none,                 - no sense - binary datastream 
    --  2=other,                - other sensing mode or fixed encoding 
    --  3=autoSwitch,           - sense both encoding and interpreter 
    -- Adobe datastream modes (default to PostScript languages) 
    -- See: Adobe "Serial and Parallel Binary Communications Protocols" 
    -- See: Adobe PostScript and PDF interpreter language specs 

XCMI Working Group                File 52conftc                [Page 96]

Xerox Common Management Interface (XCMI) Standard               04/14/23

    -- 11=psAutoSwitch,         - sense encoding, PS languages default 
    -- 12=psRaw,                - fixed Raw encoding, PS default 
    -- 13=psStandard,           - fixed Standard encoding, PS default 
    -- 14=psBCP,                - fixed BCP encoding, PS default 
    -- 15=psTBCP,               - fixed TBCP encoding, PS default 
    -- 16=psAutoSwitchBCP,      - sense PS, default to BCP encoding 
    -- 17=psAutoSwitchTBCP,     - sense PS, default to TBCP encoding 
    -- 18=psAutoSwitchRaw,      - sense PS, default to Raw encoding 
    -- 19=psAutoSwitchStandard  - sense PS, default to Standard encoding
    -- HP datastream modes (default to HP languages) 
    -- See: HP PCL, PJL, and GL interpreter language specs 
    -- 21=hpAutoSwitch,         - sense encoding, HP languages default 
    -- 22=hpText,               - fixed Text encoding, HP default 
    -- 23=hpPCL,                - fixed PCL encoding, HP default 
    -- 24=hpPJL,                - fixed PJL encoding, HP default 
    -- 25=hpGL,                 - fixed GL encoding, HP default 
    -- 26=hpAutoSwitchText,     - sense HP, default to Text encoding 
    -- 27=hpAutoSwitchPCL,      - sense HP, default to PCL encoding 
    -- 28=hpAutoSwitchPJL,      - sense HP, default to PJL encoding 
    -- 29=hpAutoSwitchGL)       - sense HP, default to GL encoding 

-- 
--          USB Protocol Suite 
-- 

xcmCOUsbSuite 
    OBJECT IDENTIFIER ::= { xcmCommsConfigTC 30 } 
    -- integerTruthValue 

xcmCOUsbPhysical 
    OBJECT IDENTIFIER ::= { xcmCOUsbSuite 1100 } 
xcmCOUsbDevice 
    OBJECT IDENTIFIER ::= { xcmCOUsbSuite 1102 } 
    -- integerNumber ('hrDeviceIndex' in IETF HR MIB, or 0=unknown) 
xcmCOUsbDeviceName 
    OBJECT IDENTIFIER ::= { xcmCOUsbDevice 1 } 
    -- stringLocalization ('xcmHrDevInfoName' in HRX, eg, '/dev/com1') 
xcmCOUsbSpeed 
    OBJECT IDENTIFIER ::= { xcmCOUsbSuite 1103 } 
    -- integerNumber (as in 'ifSpeed' in IETF MIB-II) 
xcmCOUsbSpeedOverride 
    OBJECT IDENTIFIER ::= { xcmCOUsbSpeed 1 } 
    -- integerNumber (see 'xcmCOUsbSpeed' above) 
xcmCOUsbSpeedDetected 
    OBJECT IDENTIFIER ::= { xcmCOUsbSpeed 2 } 
    -- integerNumber (see 'xcmCOUsbSpeed' above) 
xcmCOUsbSpeedAdaptive 
    OBJECT IDENTIFIER ::= { xcmCOUsbSpeed 3 } 
    -- integerTruthValue 
xcmCOUsbSpeedSupport 
    OBJECT IDENTIFIER ::= { xcmCOUsbSpeed 4 } 
    -- integerNumber (as in 'ifSpeed' in IETF MIB-II, list of speeds) 
xcmCOUsbMinSpeed 
    OBJECT IDENTIFIER ::= { xcmCOUsbSpeed 5 } 

XCMI Working Group                File 52conftc                [Page 97]

Xerox Common Management Interface (XCMI) Standard               04/14/23

    -- integerNumber (as in 'ifSpeed' in IETF MIB-II) 
xcmCOUsbMaxSpeed 
    OBJECT IDENTIFIER ::= { xcmCOUsbSpeed 6 } 
    -- integerNumber (as in 'ifSpeed' in IETF MIB-II) 
xcmCOUsbBidirectional 
    OBJECT IDENTIFIER ::= { xcmCOUsbSuite 1104 } 
    -- integerTruthValue 
xcmCOUsbInputTimeout            -- POSIX.1 'VTIME' * 10 (in 'termios.h')
    OBJECT IDENTIFIER ::= { xcmCOUsbSuite 1105 } 
    -- integerNumber (seconds, 0=infinite or 1..n) 
xcmCOUsbOutputTimeout 
    OBJECT IDENTIFIER ::= { xcmCOUsbSuite 1106 } 
    -- integerNumber (seconds, 0=infinite or 1..n) 
xcmCOUsbMinInputChars           -- POSIX.1 'VMIN' (in 'termios.h') 
    OBJECT IDENTIFIER ::= { xcmCOUsbSuite 1108 } 
    -- integerNumber (0=infinite or 1..n) 
xcmCOUsbMaxInputChars           -- POSIX.1 'nbyte' (in 'read()') 
    OBJECT IDENTIFIER ::= { xcmCOUsbSuite 1109 } 
    -- integerNumber (0=infinite or 1..n) 


xcmCOUsbConnectionModeTools  
    OBJECT IDENTIFIER ::= { xcmCOUsbSuite 1110 } 
    -- integerTruthValue (1=Direct Printing via Driver) 

xcmCOUsbPortsRearEnabled  
    OBJECT IDENTIFIER ::= { xcmCOUsbSuite 1112 } 
    -- integerTruthValue 

xcmCOUsbPortsRear1Enabled 
    OBJECT IDENTIFIER ::= { xcmCOUsbPortsRearEnabled 1 } 
    -- integerTruthValue 

xcmCOUsbPortsRear2Enabled 
    OBJECT IDENTIFIER ::= { xcmCOUsbPortsRearEnabled 2 } 
    -- integerTruthValue 

xcmCOUsbPortsRearAuxAEnabled 
    OBJECT IDENTIFIER ::= { xcmCOUsbPortsRearEnabled 3 } 
    -- integerEnum   
    -- (0=Hardware does not support this USB Port,  
    --  1=true/enabled/on,   
    --  2=false/disabled/off) 

xcmCOUsbPortsRearLeftAuxAEnabled 
    OBJECT IDENTIFIER ::= { xcmCOUsbPortsRearEnabled 4 } 
    -- integerEnum   
    -- (0=Hardware does not support this USB Port,  
    --  1=true/enabled/on,   
    --  2=false/disabled/off) 

xcmCOUsbPortsRearUpperAuxAEnabled 
    OBJECT IDENTIFIER ::= { xcmCOUsbPortsRearEnabled 5 } 

XCMI Working Group                File 52conftc                [Page 98]

Xerox Common Management Interface (XCMI) Standard               04/14/23

    -- integerEnum   
    -- (0=Hardware does not support this USB Port,  
    --  1=true/enabled/on,   
    --  2=false/disabled/off) 

xcmCOUsbPortsRearRightAuxAEnabled 
    OBJECT IDENTIFIER ::= { xcmCOUsbPortsRearEnabled 6 } 
    -- integerEnum   
    -- (0=Hardware does not support this USB Port,  
    --  1=true/enabled/on,   
    --  2=false/disabled/off) 

xcmCOUsbPortsRearLowerAuxAEnabled 
    OBJECT IDENTIFIER ::= { xcmCOUsbPortsRearEnabled 7 } 
    -- integerEnum   
    -- (0=Hardware does not support this USB Port,  
    --  1=true/enabled/on,   
    --  2=false/disabled/off) 

xcmCOUsbPortsRearBEnabled 
    OBJECT IDENTIFIER ::= { xcmCOUsbPortsRearEnabled 8 } 
    -- integerEnum   
    -- (0=Hardware does not support this USB Port,  
    --  1=true/enabled/on,   
    --  2=false/disabled/off) 

xcmCOUsbPortsFrontEnabled  
    OBJECT IDENTIFIER ::= { xcmCOUsbSuite 1113 } 
    -- integerTruthValue 

xcmCOUsbPortsFrontMainEnabled   
    OBJECT IDENTIFIER ::= { xcmCOUsbPortsFrontEnabled 1 }  
    -- integerTruthValue 

xcmCOUsbPortsFrontAuxiliaryEnabled   
    OBJECT IDENTIFIER ::= { xcmCOUsbPortsFrontEnabled 2 }  
    -- integerTruthValue  

xcmCOUsbPortSleepMode 
    OBJECT IDENTIFIER ::= { xcmCOUsbSuite 1114 } 
    -- integerTruthValue 

xcmCOUsbFeatureEnabled 
    OBJECT IDENTIFIER ::= { xcmCOUsbSuite 1115 } 
    -- integerEnum  
    -- (0=Hardware does not support this USB Port, 
    --  1=true/enabled/on,  
    --  2=false/disabled/off) 


xcmCOWirelessSuite 
    OBJECT IDENTIFIER ::= { xcmCommsConfigTC 31 } 
    -- integerTruthValue 

XCMI Working Group                File 52conftc                [Page 99]

Xerox Common Management Interface (XCMI) Standard               04/14/23


xcmCOWiFiEnabled  
    OBJECT IDENTIFIER ::= { xcmCOWirelessSuite 1100 } 
    -- integerTruthValue 



xcmCOWiFiDirectEnabled  
    OBJECT IDENTIFIER ::= { xcmCOWirelessSuite 1150 } 
    -- integerTruthValue 


xcmCOWiFiDirectIPv4SubnetAddressPrefix  
    OBJECT IDENTIFIER ::= { xcmCOWirelessSuite 1151 } 
    -- stringLocalization (IPv4 - dotted decimal 'a.b.c.d') 
    -- (IPv4 prefix = first three octets defined of the four octet  
    --   string e.g. '13.226.19.0') 


xcmCOWiFiDirectWPSName  
    OBJECT IDENTIFIER ::= { xcmCOWirelessSuite 1152 } 
    -- stringLocalization (range 1-32 characters) 
    -- (format = "XRX <model> (<last 6 digits of MAC address>)") 
    -- (   where <model> is an abbreviation of the following device 
    -- (   models: "WC" for WorkCentre, "CQ" for ColorQube,  
    -- (                  "Ph" for Phaser, and "Dev" for Device) 
    -- (e.g. 'XRX WC 7556 (D45074)') 

xcmCOWiFiSSID  
    OBJECT IDENTIFIER ::= { xcmCOWirelessSuite 1200 } 
    -- stringLocalization (32 character string in UTF-8 format) 

xcmCOWiFiSecurityMode  
    OBJECT IDENTIFIER ::= { xcmCOWirelessSuite 1300 } 
    -- integerEnum (1=None, 2=WEP, 3=WPA/WPA2 Personnel,  
    --              4=WPA2 Personnel, 5=WPA/WPA2 Enterprise,  
    --              6=WPA2 Enterprise),7= WPA3 Personal-Transition 
 --    (WPA2/WPA3 Personal), 8=WPA3 Personal-Only, 
 --    9= WPA3 Enterprise-Transition  
 --    (WPA2/WPA3 Enterprise),10=WPA3 Enterprise-Only 
 --    11= WPA3 Enterprise-192-bit 

xcmCOWiFiSecurityWEPSettings  
    OBJECT IDENTIFIER ::= { xcmCOWirelessSuite 1301 } 
    -- integerEnum (1=WEP-128bits, 2=WEP-64bits) 

xcmCOWiFiSecurityWEPKeyStringType  
    OBJECT IDENTIFIER ::= { xcmCOWirelessSuite 1302 } 
    -- integerEnum (1=ASCII string, 2=HEX string) 

xcmCOWiFiSecurityWEPKeyString  

XCMI Working Group               File 52conftc                [Page 100]

Xerox Common Management Interface (XCMI) Standard               04/14/23

    OBJECT IDENTIFIER ::= { xcmCOWirelessSuite 1303 } 
    -- stringLocalization (13 ASCII character string or  
    --                     26 HEX character string) 

xcmCOWiFiSecurityServerValidation  
    OBJECT IDENTIFIER ::= { xcmCOWirelessSuite 1304 } 
    -- stringLocalization (32 character string in UTF-8 format) 

xcmCOWiFiSecurityDeviceCertificate  
    OBJECT IDENTIFIER ::= { xcmCOWirelessSuite 1305 } 
    -- stringLocalization (255 character string) 

xcmCOWiFiSecurityDeviceName 
    OBJECT IDENTIFIER ::= { xcmCOWirelessSuite 1306 } 
    -- stringLocalization (255 character string) 

xcmCOWiFiSecurityPassword  
    OBJECT IDENTIFIER ::= { xcmCOWirelessSuite 1307 } 
    -- stringLocalization (255 character string) 
    -- NOTE: this is a WRITE-ONLY attribute; all SNMP requests  
    --       to retrieve this attribute shall return a blank value 

xcmCOWiFiEncryptionAlgorithm  
    OBJECT IDENTIFIER ::= { xcmCOWirelessSuite 1400 } 
    -- integerEnum (1=Auto, 2=TKIP, 3=TKIP+CCMP, 4=CCMP) 

xcmCOWiFiAuthenticationMethod  
    OBJECT IDENTIFIER ::= { xcmCOWirelessSuite 1500 } 
    -- integerEnum (1=PEAPv0-MS-CHAPv2, 2=EAP-TLS, 3=EAP-TLLS/PAP,  
    --              4=EAP-TLLS/MSCHAPv2, 5=EAP-TTLS/EAP-TLS) 

xcmCOWiFiAuthenticationOuterIdentity  
    OBJECT IDENTIFIER ::= { xcmCOWirelessSuite 1501 } 
    -- stringLocalization (255 character string) 

xcmCOWiFiFrequencyBands -- Wi-Fi Frequency Band 
    OBJECT IDENTIFIER ::= { xcmCOWirelessSuite 1502 } 
    -- integerEnum (1=Auto, 2=2.4GHz, 3=3.65GHz, 4=4.9GHz, 5=5GHz, 
    --              6=5.9Ghz,7=60GHz, 8=900MHz) 

xcmCOWiFiNetworkType -- Wi-Fi Network Type 
    OBJECT IDENTIFIER ::= { xcmCOWirelessSuite 1503 } 
    -- integerEnum (1=Infrastructure Mode, 2=Ad-hoc Mode) 

xcmCOWiFiNetworkList -- Wi-Fi Network List  
    OBJECT IDENTIFIER::= { xcmCOWirelessSuite 1504 } 
    -- stringLocalization (0-256 characters) 
    -- The list of discovered Wi-Fi networks 

xcmCOWiFiNetworkInUse -- Wi-Fi Network In Use  
    OBJECT IDENTIFIER::= { xcmCOWirelessSuite 1505 } 
    -- stringLocalization (0-256 characters) 
    -- The Wi-Fi network the device is connected to 


XCMI Working Group               File 52conftc                [Page 101]

Xerox Common Management Interface (XCMI) Standard               04/14/23


xcmCOWiFiBSSID -- Base Station ID 
    OBJECT IDENTIFIER::= { xcmCOWirelessSuite 1600 } 
    -- stringLocalization (0-96 characters, 12 octets for BSSID Address)
    -- Base Station ID of the access point of the wi-fi network 

xcmCOWiFiMACAddress -- mac address of wifi adapter 
    OBJECT IDENTIFIER::= { xcmCOWirelessSuite 1700 } 
    -- stringLocalization (0-96 characters, hex format, 12 octets for 
    --                     mac Address) 




xcmCONFCSuite  
    OBJECT IDENTIFIER ::= { xcmCommsConfigTC 32 } 
    -- integerTruthValue (1=true, required hardware is installed in 
    --                    device, 2=false, device is missing hardware) 

xcmCONFCEnabled  
    OBJECT IDENTIFIER ::= { xcmCONFCSuite 1100 } 
    -- integerTruthValue (1=true, feature is enabled,  
    --                    2=false, feature is disabled) 



xcmCOWiredSuite 
    OBJECT IDENTIFIER ::= { xcmCommsConfigTC 33 } 
    -- integerTruthValue 

xcmCOWiredSecurityEnabled 
    OBJECT IDENTIFIER ::= { xcmCOWiredSuite 1100 } 
    -- integerTruthValue 

xcmCOWiredSecurityUsername 
    OBJECT IDENTIFIER ::= { xcmCOWiredSuite 1200 } 
    -- stringLocalization (64 character string in UTF-8 format) 

xcmCOWiredSecurityPassword 
    OBJECT IDENTIFIER ::= { xcmCOWiredSuite 1300 } 
    -- stringLocalization (32 character string in UTF-8 format) 

xcmCOWiredSecurityAuthenticationMethod 
    OBJECT IDENTIFIER ::= { xcmCOWiredSuite 1400} 
    -- integerEnum (1=EAP-MD5, 2=PEAPv0-MS-CHAPv2. 
    --                         3=EAP- MSCHAPv2, 4=EAP-TLS) 

xcmCOWiredSecurityServerValidation 
    OBJECT IDENTIFIER ::= { xcmCOWiredSuite 1500 } 
    -- stringLocalization (64 character string in UTF-8 format) 


XCMI Working Group               File 52conftc                [Page 102]

Xerox Common Management Interface (XCMI) Standard               04/14/23


xcmCOWiredSecurityDeviceCertificate 
    OBJECT IDENTIFIER ::= { xcmCOWiredSuite 1600 } 
    -- stringLocalization (64 character string in UTF-8 format) 



xcmCOBlueToothSuite 
    OBJECT IDENTIFIER ::= { xcmCommsConfigTC 34 } 

xcmCOBlueToothInstalled 
    OBJECT IDENTIFIER ::= { xcmCOBlueToothSuite 1100 } 
    -- integerTruthValue 

xcmCOBluetoothAirPrintiBeaconEnabled  
    OBJECT IDENTIFIER ::= { xcmCOBlueToothSuite 1110 } 
    -- integerTruthValue 

xcmCOBluetoothAirPrintiBeaconUseSystemIpAddress  
    OBJECT IDENTIFIER ::= { xcmCOBlueToothSuite 1111 } 
    -- integerTruthValue 

xcmCOBluetoothAirPrintiBeaconIpAddress 
    OBJECT IDENTIFIER ::= { xcmCOBlueToothSuite 1112 } 
    -- stringLocalization 
    -- (Valid IPv4 address characters are 0123456789 and "." 
    -- Valid IPv6 address characters are 0123456789abcdef and ":" 
    -- ABCDEF are also valid, but not recommended per "A Recommendation 
    -- for IPv6 Address Text Representation" RFC5952 section 4.3) 

xcmCOBluetoothAirPrintBeaconingIpAddres 
    OBJECT IDENTIFIER ::= { xcmCOBlueToothSuite 1113 } 
    -- stringLocalization 
    -- (Valid IPv4 address characters are 0123456789 and "." 
    -- Valid IPv6 address characters are 0123456789abcdef and ":" 
    -- ABCDEF are also valid, but not recommended per "A Recommendation 
    -- for IPv6 Address Text Representation" RFC5952 section 4.3) 

xcmCOBluetoothAirPrintAdminSelectedIpAddress 
    OBJECT IDENTIFIER ::= { xcmCOBlueToothSuite 1114 } 
    -- stringLocalization 
    -- (Valid IPv4 address characters are 0123456789 and "." 
    -- Valid IPv6 address characters are 0123456789abcdef and ":" 
    -- ABCDEF are also valid, but not recommended per "A Recommendation 
    -- for IPv6 Address Text Representation" RFC5952 section 4.3) 

xcmCOBluetoothAirPrintBeaconRoutableIpAddrs 
    OBJECT IDENTIFIER ::= { xcmCOBlueToothSuite 1115 } 
    -- stringLocalization 
    -- (Valid IPv4 address characters are 0123456789 and "." 
    -- Valid IPv6 address characters are 0123456789abcdef and ":" 
    -- ABCDEF are also valid, but not recommended per "A Recommendation 
    -- for IPv6 Address Text Representation" RFC5952 section 4.3) 

XCMI Working Group               File 52conftc                [Page 103]

Xerox Common Management Interface (XCMI) Standard               04/14/23


xcmCOUsbDatalinks 
    OBJECT IDENTIFIER ::= { xcmCOUsbSuite 1200 } 
    -- integerTruthValue 

xcmCOUsbProtocol 
    OBJECT IDENTIFIER ::= { xcmCOUsbDatalinks 1 } 
    -- integerEnum (see 'xcmCODirectPrintProtocol' below) 

-- 
--          The Comms Config TC Dummy Group (DO NOT USE) 
-- 
--          DO NOT USE - Present to suppress compiler warnings ONLY! 
-- 
--          Note:  The following objects have 'odd' use of case in their
--          names (ie, 'xCm...'), in order to make obvious their related
--          textual conventions 

xCmCommsConfigDummy OBJECT IDENTIFIER ::= { xcmCommsConfigTC 999 } 

xCmSnmpNetbiosAddress OBJECT-TYPE 
    SYNTAX      XcmSnmpNetbiosAddress 
    MAX-ACCESS  not-accessible 
    STATUS      current 
    DESCRIPTION "Dummy - DO NOT USE" 
    ::= { xCmCommsConfigDummy 1 } 

xCmCommsConfigGroupSupport OBJECT-TYPE 
    SYNTAX      XcmCommsConfigGroupSupport 
    MAX-ACCESS  not-accessible 
    STATUS      current 
    DESCRIPTION "Dummy - DO NOT USE" 
    ::= { xCmCommsConfigDummy 2 } 

xCmCommsDirRecordType OBJECT-TYPE 
    SYNTAX      XcmCommsDirRecordType 
    MAX-ACCESS  not-accessible 
    STATUS      current 
    DESCRIPTION "Dummy - DO NOT USE" 
    ::= { xCmCommsConfigDummy 3 } 

xCmCommsDirAttributeType OBJECT-TYPE 
    SYNTAX      XcmCommsDirAttributeType 
    MAX-ACCESS  not-accessible 
    STATUS      current 
    DESCRIPTION "Dummy - DO NOT USE" 
    ::= { xCmCommsConfigDummy 4 } 

xCmCommsLDAPAttributeType OBJECT-TYPE 
    SYNTAX      XcmCommsLDAPAttributeType 
    MAX-ACCESS  not-accessible 
    STATUS      current 
    DESCRIPTION "Dummy - DO NOT USE" 
    ::= { xCmCommsConfigDummy 5 } 

XCMI Working Group               File 52conftc                [Page 104]

Xerox Common Management Interface (XCMI) Standard               04/14/23


xCmSnmpIPHostnameAddress OBJECT-TYPE 
    SYNTAX      XcmSnmpIPHostnameAddress  
    MAX-ACCESS  not-accessible 
    STATUS      current 
    DESCRIPTION "Dummy - DO NOT USE" 
    ::= { xCmCommsConfigDummy 6 } 
END 















































XCMI Working Group               File 52conftc                [Page 105]

Xerox Common Management Interface (XCMI) Standard               04/14/23



5.  Acknowledgements

-- 
-- 

































XCMI Working Group               File 52conftc                [Page 125]

Xerox Common Management Interface (XCMI) Standard               04/14/23
                           TABLE OF CONTENTS                            

1.  Introduction ...............................................       2
2.  SNMP Network Management Framework ..........................       2
3.  Managed Object Usage .......................................       3
  3.1.  Overview of Groups in CC MIB ...........................       3
  3.2.  Relationship of CC MIB to other MIBs ...................       4
    3.2.1.  IETF Interfaces Group MIB (RFC 2233) ...............       4
    3.2.2.  IETF Communications MIBs ...........................       4
    3.2.3.  XCMI Communications Engine MIB .....................       4
    3.2.4.  XCMI General MIB for Reconfiguration ...............       4
  3.3.  Comms Option Instance Resolution .......................       5
  3.4.  SNMP Transport Protocols and Domains ...................       6
    3.4.1.  SNMP over Internet UDP .............................       6
    3.4.2.  SNMP over OSI CLNS .................................       6
    3.4.3.  SNMP over OSI CONS .................................       6
    3.4.4.  SNMP over AppleTalk DDP ............................       7
    3.4.5.  SNMP over NetWare IPX ..............................       7
    3.4.6.  SNMP over NetBIOS (session) ........................       7
    3.4.7.  SNMP over NetBEUI (datalink) .......................       7
    3.4.8.  SNMP over Internet TCP (Experimental) ..............       7
    3.4.9.  SNMP over UDP using hostname instead of IP address .       8
4.  Managed Object Definitions .................................       9
  4.1.  Definition of CC Textual Conventions ...................       9
    4.1.1.  xcmSnmpNetbiosDomain ...............................      10
    4.1.2.  XcmSnmpNetbiosAddress ..............................      10
    4.1.3.  xcmSnmpIPHostnameDomain ............................      10
    4.1.4.  XcmSnmpIPHostnameAddress ...........................      10
    4.1.5.  REGISTRY of XCMI Standard NetBIOS Ports ............      11
    4.1.6.  XcmCommsConfigGroupSupport .........................      11
    4.1.7.  XcmCommsDirRecordType ..............................      11
    4.1.8.  XcmCommsDirAttributeType ...........................      12
    4.1.9.  XcmCommsLDAPAttributeType ..........................      20
    4.1.10.  Special Comms Option Types ........................      22
    4.1.11.  OSI LAN Protocol Suite ............................      27
    4.1.12.  OSI WAN Protocol Suite ............................      32
    4.1.13.  Internet Protocol Suite ...........................      37
    4.1.14.  AppleTalk Protocol Suite ..........................      75
    4.1.15.  NetWare Protocol Suite ............................      79
    4.1.16.  Vines Protocol Suite ..............................      84
    4.1.17.  NetBIOS Protocol Suite ............................      87
    4.1.18.  NetBEUI Protocol Suite ............................      91
    4.1.19.  Serial Protocol Suite .............................      92
    4.1.20.  Parallel Protocol Suite ...........................      94
    4.1.21.  Direct Print Protocol Suite (Serial/Parallel) .....      96
    4.1.22.  USB Protocol Suite ................................      97
5.  Acknowledgements ...........................................     106









XCMI Working Group                File 52conftc                 [Page i]
